Краткое содержание страницы № 1
1028310
4-POINT SUB-FRAME MOUNTING KIT
for BH90-X Backhoe
®
on New Holland Tractors
TT60A, TT75A
includes Hose Kits
1028360, 1029730
and Mount Kit 1029700
SAVE THIS
MANUAL!
Include it with the
backhoe manual. It
contains safety,
operation, and repair
part information not
found in other
manuals.
MAN0715
(Rev. 10/31/2008)
INSTALLATION MANUAL
Краткое содержание страницы № 2
TO THE DEALER: ® Assembly and proper installation of this product is the responsibility of the Woods dealer. Read manual instructions and safety rules. Make sure all items on the Dealer’s Pre-Delivery and Delivery Check Lists in the Operator’s Manual are completed before releasing equipment to the owner. The dealer must complete the Product Registration online at the Woods Dealer Website or complete the mail-in form included with the Operator’s Manual. If using the mail-in form, the dealer is to
Краткое содержание страницы № 3
SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Make sure that all operating and service person- ! nel know that if hydraulic fluid penetrates skin, it LEA EL INSTRUCTIVO! must be surgically removed as soon as possible by Si no lee Ingles, pida ayuda a a doctor familiar with this form of injury or gan- alguien que si lo lea para que le grene, serious injury, or death will result. CON- traduzca las medidas de seguridad. TACT A PHYSICIAN IMMEDIATELY IF FLUID ENTERS SKIN OR EYES. D
Краткое содержание страницы № 4
SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! (Safety Rules continued from previous page) Do not allow bystanders in the area when oper- ating, attaching, removing, assembling, or servic- Make sure all hydraulic hoses, fittings, and ing equipment. valves are in good condition and not leaking before Before operating, make sure stabilizer pads are starting power unit or using equipment. Check and lowered firmly to the ground. Stabilizer arms pro- route hoses carefully to preven
Краткое содержание страницы № 5
BACKHOE SUB-FRAME INSTALLATION Tractor Preparation ■ Only use 1028310 4-Point Sub-Frame Mount- ing Kit for mounting Woods BH90-X backhoe on ® New Holland TT60A or TT75A tractors equipped with Woods LU126 loader. Use mount kit 1029700 and 1028310 Sub-Frame Mounting Kit to mount ® Woods BH90-X backhoe on New Holland TT60A or TT75A tractors equipped with New Holland 620TL Loader. Any other use or modification of this mounting kit may result in serious injury or death. For installing this
Краткое содержание страницы № 6
Install 1029700 Mount Kit For New Holland Loader Mount Only This mount kit is needed to connect sub-frame mount- ing kit 1028310 to the New Holland 620TL loader mount. 1. Remove toolbox and toolbox bracket from the right loader mount if equipped. 2. Attach right backhoe bracket (1) to the inside of New Holland loader mount and toolbox bracket (3) to the outside of loader mount. 3. Secure using two cap screws (4), hardened flat washers (5), one tube support (7) and two flange Figure 3. Right
Краткое содержание страницы № 7
Install Tractor Brackets 1. Place right tractor bracket (1) under right side of tractor. Use a hydraulic floor jack to help raise ROPS and hold tractor bracket in position. Hardware 2. Attach right tractor bracket (1) to right loader mount or right backhoe bracket (New Holland Mount) using one hex flange screw (11) and hex flange nut (18). See Figure 7. 3. Raise tractor bracket up and attach it to the bot- tom of the rear axle using ROPS hardware previ- ously removed. 11 18 4. Secure tractor
Краткое содержание страницы № 8
Attach Backhoe Mounts to Backhoe NOTE: Leave all hardware loose until backhoe has been mounted to the tractor. 1. Attach right backhoe mount (3) and left backhoe mount (4) to backhoe frame. 2. Secure into position using six (three per bracket) cap screws (10), hardened flat washers (13), and hex nuts (17). 3. Secure crossbrace (5) to backhoe brackets using four cap screws (12), hardened flat washers (15), and hex nuts (19). 3. 1014450 Right backhoe mount 4. 1014451 Left backhoe mount 5. 1014
Краткое содержание страницы № 9
1028360 HOSE KIT Install Fittings and Hose 1028360 Hose Kit is used to connect backhoe 1. 1028358 Hose, 60" x 3/8 NPTM x 7/8 JICM hydraulic hoses to the tractor rear hydraulic valve and 4. 1010920 Adapter, M22 x 3/4 JICM the Woods loader control valve. 5. 315036 Adapter, 3/8 NPTM x 3/4 JICF 1. Attach adapter (4), adapter (5) and female quick 6. 64299 Quick coupler, female 3/8 coupler (6) into the opening on the hydraulic valve 7. 64300 Quick coupler, male 3/8 at the rear of the axle. 2. Attach
Краткое содержание страницы № 10
1029730 HOSE KIT Install Fittings 1029730 Hose Kit is used to connect backhoe hydraulic hoses to the tractor hydraulic line and the New Holland loader control valve. 1. Disconnect the loader control valve PBY hose from the hydraulic hard line below the tractor seat. 2. Attach adapter (2), adapter (6) and female quick coupler (4) to the hydraulic hard line (Figure 13). 6 3. Attach adapter (3), adapter (6) and male quick 2 4 coupler (5) to the PBY hose from the loader con- trol valve. DP10 4.
Краткое содержание страницы № 11
Mount Backhoe to Tractor Check Hydraulic System Check all hydraulic fittings and lines to be sure they are tight and free of kinks or twists. Mount Backhoe This mounting kit is designed to provide 1. Remove the backhoe seat assembly. secure mounting and adequate operator clear- ance for most operators when properly installed. 2. Back tractor up to backhoe and center mount Check clearance dimensions shown below to be between the tractor rear tires. Position tractor so sure you have inst
Краткое содержание страницы № 12
Mount Backhoe to Tractor (Continued) 10. Install cap screws (9) and slotted hex nuts (16). Refer to Figure 16. Tighten with 1-1/2 inch open end wrench provided 5. Using the backhoe hydraulics position the back- with kit. Return wrench to storage position (see hoe brackets at a slight angle, approximately 5 to Figure 16). 10 degrees. 11. Secure hex nut into position with klik pin (20). 6. Raise backhoe up by lowering stabilizers and 12. Shut off tractor and remove key. boom section until ba
Краткое содержание страницы № 13
Remove Backhoe from Tractor 7. Use the boom to relieve excess pressure on 1 inch bolts and remove bolts. 8. Tilt backhoe main frame to separate slots on the The only time the backhoe may be operated backhoe brackets from the tractor brackets. from a position other than the operator seat is 9. Raise stabilizers until backhoe brackets slide out during backhoe attachment and removal. Opera- of hooks on the bottom of the tractor brackets. tor must: � Read Mounting Kit Manual instructions
Краткое содержание страницы № 14
STORAGE Connect Hydraulic Hoses Loader PBY Hose NOTICE ■ Failure to connect hoses together will result in damage to tractor hydraulic system. Tractor & Woods Loader: Connect male quick cou- pler on end of hose from loader control valve to female quick coupler in rear hydraulic valve when backhoe is removed from tractor. See Figure 18. Make sure 3-point lift arms do not interfere with hose. Adjust hose as necessary to prevent interference. Tractor & New Holland Loader: Connect male quick couple
Краткое содержание страницы № 15
1028310 4-POINT SUB-FRAME MOUNTING KIT 21 - PN 1006885 WARNING PINCH POINT Keep hands clear. 1006885 MODEL NO. SERIAL NO. Woods Equipment Company Oregon, Illinois, U.S.A. REF PART QTY DESCRIPTION REF PART QTY DESCRIPTION 1 1028308 1 Right tractor bracket 14 57817 8 5/8 Hardened flat washer 2 1028309 1 Left tractor bracket 15 57816 4 1/2 Hardened flat washer 3 1014450 1 Right backhoe bracket 16 1006861 2 1" NC Slotted hex nut 4 1014451 1 Left backhoe bracket 17 1450 * 6 3/4 NC Hex nut 5 1014467
Краткое содержание страницы № 16
1029700 MOUNTING KIT REF PART QTY DESCRIPTION 1 1029702 1 Right backhoe bracket 2 1029703 1 Left backhoe bracket 3 1029704 1 Toolbox bracket 4 300469 * 4 5/8 NC x 6-1/2 HHCS GR5 5 57817 4 5/8 Hardened flat washer 6 19025 * 4 5/8 NC flange lock nut 7 1029774 2 Tube support * Standard hardware, obtain locally 1028360 HOSE KIT REF PART QTY DESCRIPTION 1 1028358 1 Hose, 60" x 3/8 NPTM x 7/8 JICM 2 1013325 2 Hose, 48" x 3/8 NPTM x 3/4 JICF 3 316016 2 Adapter, 3/4 JICM x 7/8 ORBM 4 1010920 1 Adapter,
Краткое содержание страницы № 17
1029730 HOSE KIT REF PART QTY DESCRIPTION 1 1029729 2 Hose, 72" x 3/8 NPTM x 3/4 JICF 2 1002613 1 Adapter, M22 x1.5F x 3/4 JICM 3 1010920 1 Adapter, M22 x 1.5M x 3/4 JICM 4 64299 2 Quick coupler, female 5 64300 2 Quick coupler, male 6 315036 2 Adapter, 3/8 NPTM x 3/4 JICF 7 316016 2 Adapter, 3/4 JICM x 7/8 ORBM MAN0715 (Rev. 10/31/2008) Parts 17
Краткое содержание страницы № 18
BOLT TORQUE CHART Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific application. Fasteners must always be replaced with the same grade as specified in the manual parts list. Always use the proper tool for tightening hardware: SAE for SAE hardware and Metric for metric hardware. Make sure fastener threads are clean and you start thread engagement properly. All torque values are given to specifications used on hardware define
Краткое содержание страницы № 19
BOLT SIZE CHART NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts. SAE Bolt Thread Sizes 5/16 3/8 1/2 5/8 3/4 7/8 IN 1 2 7 34 5 6 MM 25 50 75 100 125 150 175 Metric Bolt Thread Sizes 8MM 10MM 12MM 14MM 16MM 18MM ABBREVIATIONS AG .............................................................. Agriculture MPa.........................................................Mega Pascal ASABE.................... American Society of Agricultural & N...
Краткое содержание страницы № 20
WARRANTY TM TM (All Models Except Mow’n Machine Zero-Turn Mowers and Woods Boundary Utility Vehicles) Please Enter Information Below and Save for Future Reference. Date Purchased: ____________________________ From (Dealer): __________________________________________ Model Number: ____________________________ Serial Number: __________________________________________ Woods Equipment Company (“WOODS”) warrants this product to be free from defect in material and workmanship. Except as otherwise set
