Краткое содержание страницы № 1
1022120
4-POINT SUB-FRAME MOUNTING KIT
for Backhoe Models
BH70-X, BH80-X
®
on New Holland Tractors
T1510, T1520 FWA
with Woods Loaders
LS84, LC96, LC102, 1009, 1012
or New Holland 7308, 110TL Loaders
Includes Hydraulic Kit
1013484
Tested. Proven. Unbeatable.
SAVE THIS
MANUAL!
Include it with the
backhoe manual. It
contains safety,
operation, and repair
part information not
found in other
manuals.
MAN0708
(4/11/2008)
INSTALLATION MANUAL
Краткое содержание страницы № 2
TO THE DEALER: ® Assembly and proper installation of this product is the responsibility of the Woods dealer. Read manual instructions and safety rules. Make sure all items on the Dealer’s Pre-Delivery and Delivery Check Lists in the Operator’s Manual are completed before releasing equipment to the owner. The dealer must complete the Product Registration online at the Woods Dealer Website or complete the mail-in form included with the Operator’s Manual. If using the mail-in form, the dealer is to
Краткое содержание страницы № 3
SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Make sure that all operating and service person- ! nel know that if hydraulic fluid penetrates skin, it LEA EL INSTRUCTIVO! must be surgically removed as soon as possible by Si no lee Ingles, pida ayuda a a doctor familiar with this form of injury or gan- alguien que si lo lea para que le grene, serious injury, or death will result. CON- traduzca las medidas de seguridad. TACT A PHYSICIAN IMMEDIATELY IF FLUID ENTERS SKIN OR EYES. D
Краткое содержание страницы № 4
SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! (Safety Rules continued from previous page) Do not allow bystanders in the area when oper- ating, attaching, removing, assembling, or servic- Make sure all hydraulic hoses, fittings, and ing equipment. valves are in good condition and not leaking before Before operating, make sure stabilizer pads are starting power unit or using equipment. Check and lowered firmly to the ground. Stabilizer arms pro- route hoses carefully to preven
Краткое содержание страницы № 5
BACKHOE SUB-FRAME INSTALLATION Tractor Preparation ■ Only use 1022120 4-Point Sub-Frame Mount- ing Kit for mounting Woods BH70-X, BH80-X ® backhoe on New Holland T1510, T1520 tractor equipped with Woods LS84, LC96, LC102, 1009, 1012 loaders or New Holland 7308, 110TL loaders. Any other use or modification of this mounting kit may result in serious injury or death. For installing this sub-frame, references to right, left, DP17 forward and rearward directions are determined from the oper
Краткое содержание страницы № 6
Install Front Mounts With Woods LS84 Loader Mount Attach front mount (10) to the right loader mount using two cap screws (32), four hardened flat wash- ers (29) and two hex nuts (23). 10. 1026846 Front mount (LS84 only) 23. 230 5/8 NC Hex nut 29. 57817 5/8 Hardened flat washer 32. 902 5/8 NC x 2 HHCS GR5 Figure 3. Front Mount Installation With New Holland 7308, 110TL Loader Mounts or Woods LC96, LC102, 1009, 1012 Loader Mounts 1. Remove two bolts connecting right and left loader 24 mount/mid-
Краткое содержание страницы № 7
Install ROPS Brackets 1. Place ROPS bracket (33) under rear axle and secure to ROPS using two cap screws (30) and hardened flat washers (28). NOTE: Bracket must be orientated with the "short" side towards the outside of the tractor. 2. Repeat for opposite side of tractor. 30. 59036 M12 x 1.75P x 150 mm HHCS 30 28. 57816 1/2 Hardened flat washer 33. 1022125 ROPS bracket, link 33 DP2 Figure 7. ROPS Bracket Installed - Right Side Install Tractor Brackets With Woods LS84 Loader Mount 4. Place ri
Краткое содержание страницы № 8
Install Tractor Brackets With New Holland 7308, 110TL Loader Mount or Woods LC96, LC102, 1009, 1012 Loader Mount 1. Place left tractor bracket (4) under left side of tractor. Use a hydraulic floor jack to help raise and hold tractor bracket in position. 2. Attach left tractor bracket to left front mount (9) using two cap screws (32), four hardened flat washers (29), and two hex nuts (23). NOTE: Tractors equipped with mid-mount mower, place tractor bracket on the inside of front mount as show
Краткое содержание страницы № 9
Install Cross Brace 1. Remove PTO shield. 6. 1013477 Cross brace 2. Attach cross brace (6) to rear of tractor using two 20. 1026373 M16 x 2.0P x 40 mm HFS CL10.9 hex flange screws (20). 21. 1093 1/2 NC Hex nut 3. Attach to right and left tractor brackets using four 26. 3699 1/2 NC x 2 HHCS GR5 (two per side) cap screws (26), eight hardened 28. 57816 1/2 Hardened flat washer flat washers (28), and four hex nuts (21). 4. Install PTO shield. 26 20 28 Figure 12. Cross Brace Installation Figure
Краткое содержание страницы № 10
Torque Mounting Hardware NOTICE ■ Check torque value of mount hardware after 10 hours of operation and again after every 50 hours of operation. TORQUE SPECIFICATIONS Wrench Ref Cap Screw Qty Size Required Torque 20 M16 x 2.0P x 40 mm FHCS CL10.9 2 24 mm 173 lbs-ft (234 N-m) 24 M16 x 2.0P x 55 mm CL8.8 2 24 mm 125 lbs-ft (169 N-m) 25 M16 x 2.0P x 70 mm CL8.8 2 24 mm 125 lbs-ft (169 N-m) 26 1/2 NC x 2 GR5 16 3/4" 85 lbs-ft (115 N-m) 30 M12 x 1.75P x 150 mm CL8.8 4 18 mm 50 lbs-ft (68 N-m) 32 5/8
Краткое содержание страницы № 11
HYDRAULIC INSTALLATION Keep hands and body away from pressurized Make sure all hydraulic hoses, fittings, and lines. Use paper or cardboard, not hands or other valves are in good condition and not leaking before body parts to check for leaks. Wear safety goggles. starting power unit or using equipment. Check and Hydraulic fluid under pressure can easily penetrate route hoses carefully to prevent damage. Hoses skin and will cause serious injury or death. must not be twisted, b
Краткое содержание страницы № 12
Install Hydraulic Block and Fittings 1. Locate the hydraulic manifold block on the right 7. 2472 5/16 Lock washer side of the tractor just under the fender (Figure 8. 307130 M8 x 1.25P x 40 mm Cap screw 19) and remove the block-off cap. 9. 307134 M8 x 1.25P x 100 mm Cap screw 2. Attach hydraulic block (18) to tractor using new 11. 313049 Elbow, 9/16 ORBM x 9/16 JICM 45° O-rings (14), three cap screws (8) and one cap 14. 62726 O-ring .487 x .103 screw (9) plus washers (7). Make sure O-rings 15.
Краткое содержание страницы № 13
Install Bulkhead Adapter on Backhoe Mount 1. Attach bulkhead adapter (1) to crossmember between backhoe brackets. Secure with nut sup- plied with adapter. 2. Attach elbow (10) and female quick coupler (16) to bulkhead adapter as shown in Figure 23. 3. Position elbow and quick coupler to point upward. 1. 1006144 Adapter, Bulkhead 3/8 NPTM x 3/4 JICM 10. 313017 Elbow, 3/8 NPTM x 3/8 NPTF 90° 16. 64299 Quick coupler, female Figure 23. Bulkhead Adapter Installation - Backhoe Install Hoses to Bac
Краткое содержание страницы № 14
Mount Backhoe to Tractor Check Hydraulic System Check all hydraulic fittings and lines to be sure they are tight and free of kinks or twists. Mount Backhoe This mounting kit is designed to provide 1. Remove the backhoe seat assembly. secure mounting and adequate operator clear- ance for most operators when properly installed. 2. Back tractor up to backhoe and center mount Check clearance dimensions shown below to be between the tractor rear tires. Position tractor so sure you have inst
Краткое содержание страницы № 15
Mount Backhoe to Tractor (Continued) 10. Install cap screws (15) and slotted hex nuts (16). Refer to Figure 26. Tighten with 1-1/2 inch open end wrench provided 5. Using the backhoe hydraulics position the back- with kit. Return wrench to storage position (see hoe brackets at a slight angle, approximately 5 to Figure 26). 10 degrees. 11. Secure hex nut into position with klik pin (17). 6. Raise backhoe up by lowering stabilizers and 12. Shut off tractor and remove key. boom section until b
Краткое содержание страницы № 16
Remove Backhoe from Tractor 7. Use the boom to relieve excess pressure on 1 inch bolts and remove bolts. 8. Tilt backhoe main frame to separate slots on the The only time the backhoe may be operated backhoe brackets from the tractor brackets. from a position other than the operator seat is 9. Raise stabilizers until backhoe brackets slide out during backhoe attachment and removal. Opera- of hooks on the bottom of the tractor brackets. tor must: � Read Mounting Kit Manual instructions
Краткое содержание страницы № 17
STORAGE Connect Hydraulic Hoses TRACTOR: Connect male quick coupler on end of hose to female quick coupler at bulkhead bracket when backhoe is removed from tractor. See Figure 28. NOTICE ■ Failure to connect hoses together will result in damage to tractor hydraulic system. DP21 Figure 28. Hose Connection - Backhoe Removed BACKHOE: Connect IN and OUT quick couplers together to prevent dirt and debris from accumulating in quick couplers. See Figure 29. DP15 Figure 29. Backhoe Hose Connection,
Краткое содержание страницы № 18
1022120 4-POINT SUB-FRAME MOUNTING KIT 18 Parts MAN00708 (4/11/2008) 14 - PN 1006885 WARNING PINCH POINT Keep hands clear. 1006885 Serial Number Plate MODEL NO. SERIAL NO. Woods Equipment Company Oregon, Illinois, U.S.A.
Краткое содержание страницы № 19
1022120 SUB-FRAME MOUNTING PARTS LIST REF PART QTY DESCRIPTION REF PART QTY DESCRIPTION 1 1013464 1 Right backhoe bracket 20 1026373 2 M16 x 2.0P x 40 mm HFS CL10.9 2 1013465 1 Left backhoe bracket 21 1093 * 16 1/2 NC Hex nut 3 1022130 1 Right tractor bracket 22 1450 * 6 3/4 NC Hex nut 4 1022131 1 Left tractor bracket 23 230 * 14 5/8 NC Hex nut 5 1012852 1 Cross brace 24 307429 2 M16 x 2.0P x 55 mm HHCS 6 1013477 1 Crossmember, BH6500 link 25 307430 2 M16 x 2.0P x 70 mm HHCS 7 1022126 2 reinforc
Краткое содержание страницы № 20
1013484 HOSE KIT REF PART QTY DESCRIPTION REF PART QTY DESCRIPTION 1 1006144 1 Adapter, bulkhead 11 313049 1 Elbow, 9/16 ORBM x 9/16 JICM 45° 3/8 NPTM x 3/4 JICM 12 360215 1 Hose, 14" x 9/16 JICF x 9/16 JICF 2 1009493 1 Hose, 40" x 3/8 NPTM x 9/16 JICF 13 38604 1 Elbow, 9/16 JICM x 9/16 JICF 90° 3 1009495 1 Adapter, bulkhead 14 62726 4 O-ring .487 x .103 3/8 NPTM x 9/16 JICM 15 63558 1 Elbow, 9/16 JICM x 9/16 ORBM 4 1010924 1 Hose, 40" x 3/8 NPTM x 3/4 ORBM 16 64299 2 Quick coupler, female 5 101
