Руководство по эксплуатации Premier Mounts PWM-503

Краткое содержание страницы № 1

INSTALLATION MANUAL












PLASMA DISPLAY MOUNT MODEL

































For service and parts contact:

Premier Mounts
3130 E. Miraloma Ave
Anaheim, CA USA 92806

Phone: (800) 368-9700 Fax: (800) 832-4888

Visit us at: www.mounts.com

Краткое содержание страницы № 2

Contents o Safety & precautions o Mount diagrams o Parts List o Optional Adapters o Installing the mounting bracket o Installing the mount o Electrical o Securing the mount o Additional security - 2 -

Краткое содержание страницы № 3

Safety & Precautions WARNING: Safety precaution measures must be practiced at all times during the installation of this product. Use proper safety gear and tools for the installations procedure to prevent personal injury or damage to the plasma displays or plasma mounts. The wall or ceiling structure must be capable of supporting at least five (5) times the weight of plasma display. If not, the wall or ceiling must be reinforced. Proper installation procedure by quali

Краткое содержание страницы № 4

Mount Diagrams e 1 9 .771 1 6 . 000 TILT BACK PLATE 1. 25 0 5. 46 0 F 1 . 000 2.8 6 5 A PART#: 1. 125 1.75 0 3.5 00 PSB-TBP MATERIAL: d 12 (GA) CRS COLOR: Black powder coat 8.0 00 A. Lag bolt access slot. B. 5.000 Mounting points (4.5") used on 18. 5 00 4.500 installations other than wall mounting. C. Access hole for power or cables. 8.0 00 D. Mounting points for additional security screws. 3.25 0 4.500 b 5.460 16. 000 c MOU

Краткое содержание страницы № 5

Parts List HARDWARE LIST QTY SIZE DESCRIPTION 6 5/16” Dia Lag bolts 1 Mounting bracket 1 PSB-TBP tilt back plate 2 M6 x 12 (mm) Phillip security Used for additional security on screws tilt mounts, mobile carts, floor stands and ceiling mounts 1 Installations instructions 6 M8 x 20 Phillip screws Mount hardware TOOLS NEEDED o Phillips screwdriver o Drill gun o Soft material or a blanket o Pencil o ¼" drill bit

Краткое содержание страницы № 6

Installing the mounting bracket WARNING : Proper installation procedure by qualified personnel as outlined in the installation instructions must be adhered to. Failure to do so could result in serious personal injury and possible damage to the plasma display. Step 1 CAUTION: The plasma displays are fragile and heavy. At least two (2) qualified personnel are strongly recommended for the installation of this product. Invert the plasma display and set it on a flat and soft mat

Краткое содержание страницы № 7

Installing the mounts Step 3 Select the area where the plasma will be installed and make sure it can support the weight standards (see warning on page 3). Locate the 16" wood stud centers behind the wall using a (commercially available) stud finder and mark the center of the studs when found. Set the mounting bracket to the wall and mark the desired height by marking the center of the tilt back plate. See fig 3 Desired height marking Wall structure

Краткое содержание страницы № 8

To determine the desired viewing height, use the center slot opening in the wall mount as a center reference for the plasma television when mounted. Once the height is determined, use the bubble level t o insure that the bracket is level. Next, using a pencil, mark the six (6) lag bolt slot openings on the mounting bracket. Before continuing, confirm the marks are located on the center of the studs. Drill 1/4" pilot holes on the six (6) markings on the wall. Raise the tilt back pl

Краткое содержание страницы № 9

Securing the mount Step 5 Warning: The plasma display is heavy and 2 people are needed to lift and install it. Failure to do so could result in serious personal injury. Before placing the plasma on the wall recheck all hardware for proper tightness and security. Before installing, become familiar with the way the plasma mount attaches to the wall mount. Align the four (4) tab openings to the four (4) receiving tabs on the tilt back plate. When all four (4) the tabs are aligned slide