Руководство по эксплуатации JL Audio Slampak SLPK-CAN-SPYDER1

Краткое содержание страницы № 1

SLPK-CAN-SPYDER1_INSTR_SKU# 011312
Installat Ion

d I F F I C u l t Y :

SlamPak
If you choose to perform the installation yourself, it is absolutely vital that
®
out
the Stealthbox be properly mounted to the vehicle according to these
o F
instructions. Failure to mount the enclosure properly presents two problems:
I n s t a l l a t I o n G u I d e
for the 1) The sub-bass performance will suffer due to the movement of the enclosure
35
caused by the force exerted by the woofer(s).
SL

Краткое содержание страницы № 2

SLPK-CAN-SPYDER1_INSTR_SKU# 011312 s t e P 4 S T E P 8 Looking up from the front right tire, use a 1-1/8” hole- saw Remove the air duct body panels as indicated by the image to cut a hole for the harness to come through as seen in at left. (One on each side of the motorcycle). There may be auxiliary lights installed in this panel, unplug them as the ste P 7. panel is removed. Before drilling, always make sure that you are not going to be drilling into any gas lines, brake lines, If you a

Краткое содержание страницы № 3

SLPK-CAN-SPYDER1_INSTR_SKU# 011312 s t e P 1 2 S T E P 1 6 Looking down and towards the front right corner of the Remove gauge cluster as shown by lifting top panel then storage compartment, position the wax square as shown. depressing two locking tabs on top of the cluster. s t e P 1 3 S T E P 1 7 Thread the 3/8-16 x 1-1/4” Hex Head Bolt all the way into Put a length of masking tape as shown on each side of the the enclosure. Press the enclosure down into the storage top fairing. compartmen

Краткое содержание страницы № 4

SLPK-CAN-SPYDER1_INSTR_SKU# 011312 S T E P 2 4 S T E P 2 0 Set each pod into position, with the “U-Bolt” coming alignment of the front of each pod, once both front and rear through the two upper holes and the wire coming through alignment is achieved, use a marker to make marks on the the bottom hole. Secure the pod to the motorcycle using masking tape shown in ste P 17 through the holes in the the included 1/4 x 1” Fender Washer and 1/4” Nyloc Nut on pods identified in ste P 18. each le

Краткое содержание страницы № 5

SLPK-CAN-SPYDER1_INSTR_SKU# 011312 s t e P 2 7 S T E P 3 1 Run the power cables up the right hand side of the To mount the Remote level control, determine a convenient motorcycle, securing it as described earlier at regular and safe location, drill a 3/8” hole, intervals alongside the frame or other cable runs. Before drilling, always make sure that you are not going to be drilling into any gas lines, brake lines, tires, transmission lines, electrical wiring, exhaust systems or anything el

Краткое содержание страницы № 6

SLPK-CAN-SPYDER1_INSTR_SKU# 011312 I n C l u d e d H a R d W a R e 20) 4-9/16” Nylon Cable tie 1) 10’- 1/2” Flex Loom 8) #6-12 x 3/4” Screw 1) HD-RLC (Remote Level Control) 2) Port Bezel 1) XD-MFB-MAXI 1) XC-MINIRCA-6 2) 1/4-20 U Bolt (for Spyder) 4) Nylon Locknuts 1) 3/8-16 x 1-1/4” Hex Head Bolt 1) 3/8” Split Lock Washer 1) 3/8” x 1-1/4” Fender Washer 1) 3” x 3” Wax Square 4) 1/4 x 1” Fender Washer s P e C I F I C a t I o n s (Subwoofer) Enclosure Type: Acoustic Suspension (se

Краткое содержание страницы № 7

Краткое содержание страницы № 8