Краткое содержание страницы № 1
8x4 CAT-5 Matrix
for
EXT-HDMI-CAT5-844
User Manual
www.gefen.com www.gefen.com
Краткое содержание страницы № 2
ASKING FOR ASSISTANCE Technical Support: Telephone (818) 772-9100 (800) 545-6900 Fax (818) 772-9120 Technical Support Hours: 8:00 AM to 5:00 PM Monday thru Friday. Write To: Gefen Inc. c/o Customer Service 20600 Nordhoff St Chatsworth, CA 91311 www.gefen.com support@gefen.com Notice Gefen Inc. reserves the right to make changes in the hard ware, packaging and any accompanying doc u men ta tion without prior written notice. 8x4 CAT-5 Matrix for HDMI is a trademark of Gefen Inc. © 2008
Краткое содержание страницы № 3
CONTENTS 1 Introduction 2 Operation Notes 3 Features 4 Sender Panel Layout 5 Sender Panel Descriptions 7 Connecting And Operating The 8x4 CAT-5 Matrix for HDMI 8 Connecting The 8x4 CAT-5 Matrix for HDMI Jumpers 9 RMT-16IR Remote Control Description 10 RMT-16IR Remote Channel Confi guration 11 EDID Management Feature 12 EDID Management Options 13 LED Array Description 14 8x4 CAT-5 Matrix for HDMI RS-232 Serial Communication 15 8x4 CAT-5 Matrix for HDMI RS-232 Commands 16 Receiver Panel Layout 17 R
Краткое содержание страницы № 4
INTRODUCTION Congratulations on your purchase of the 8x4 CAT-5 Matrix for HDMI. Your complete satisfaction is very important to us. Gefen Gefen delivers innovative, progressive computer and electronics add-on solutions that harness integration, extension, distribution and conversion technologies. Gefen’s reliable, plug-and-play products supplement cross-platform computer systems, professional audio/video environments and HDTV systems of all sizes with hard-working solutions that are easy to
Краткое содержание страницы № 5
OPERATION NOTES READ THESE NOTES BEFORE INSTALLING OR OPERATING THE 8X4 CAT-5 MATRIX FOR HDMI • To use the extender functionality of the 8x4 CAT-5 Matrix for HDMI the supplied 1 foot HDMI jumper cables must be used to connect the HDMI output ports to the HDMI extension input ports. Please see page 8 for details. • Use two industry standard CAT-5, CAT-5e or CAT-6 cables to operate each of the HDMI Over CAT5 Receivers. Gefen recommends shielded CAT-6 cabling for maximum performance. • For 108
Краткое содержание страницы № 6
FEATURES Features • Switches any eight HDMI™ sources to 4 Displays • Distributes any of the four switched inputs (total of eight inputs) to any combination of the four HDMI™ output displays • Maintains high resolution video - beautiful, sharp HDTV resolutions up to 1080p, 2k, and computer resolutions up to 1920 x 1200 are easily achieved • Serial RS-232 remote port for switching via control automation • HDMI™ 1.2 Compliant (HDMI 1.3 Compatible); HDCP Compliant • Discrete IR remote (included) •
Краткое содержание страницы № 7
SENDER PANEL LAYOUT Front Panel 1 23 4 Back Panel 579 8 6 13 10 11 12 4
Краткое содержание страницы № 8
SENDER PANEL DESCRIPTIONS 1 HDMI Outputs 1 - 4 The selected source for each HDMI output will be indicated by an active LED. The LED array will behave differently depending on the selected input (A or B). Please see page 13 for more information on the LED array. 2 IR (Infrared) Receiver This receiver will accept command for switching between input HDMI devices using the optional RMT-16IR remote control. Line of sight must be preserved for proper operation. 3 IR (Infrared) Receiver Extension A
Краткое содержание страницы № 9
SENDER PANEL DESCRIPTIONS 12 HDMI Outputs 1 - 4 Each output port can be used in one of either two ways. This output can be connected directly to a local HDMI capable display or, if using the built- in extension functionality, these outputs can be connected to the HDMI extension input ports using the supplied 1 foot HDMI jumper cables. 13 24V DC Power Input Connect the supplied 24V DC Power supply to this input. 6
Краткое содержание страницы № 10
CONNECTING AND OPERATING THE 8X4 CAT-5 MATRIX FOR HDMI How to Connect the 8x4 CAT-5 Matrix for HDMI 1. Connect up to 8 HDMI source devices to the 8x4 CAT-5 Matrix for HDMI using the included HDMI cables. NOTE: Please be aware that each input has two available HDMI ports and that only one will be active at any given time. It is recommended that commonly used HDMI sources be put on separate inputs (i.e. 1A and 2A, not 1A and 1B) so that these devices are always available. 2. If using the exten
Краткое содержание страницы № 11
CONNECTING THE 8X4 CAT-5 MATRIX FOR HDMI JUMPERS The 8x4 CAT-5 Matrix for HDMI uses a jumper cable system to link the matrix and extension portions together. These jumper cables are included. Please us the diagram below to setup extension functionality of the 8x4 CAT-5 Matrix for HDMI. 1 This example shows the jumper connection between HDMI output B port 1 and HDMI extension input port 1 . A B A 2 When all jumpers are connected, extension for each HDMI output is possible. If
Краткое содержание страницы № 12
RMT-16IR* REMOTE CONTROL DESCRIPTION LED Indicator Input Selection Buttons *The RMT-16IR is an optional accessory. The RMT-16IR remote control will allow the user to select which source will be routed to which output. Each of the 4 outputs are assigned a group of 4 buttons that will correspond to the 4 source inputs. Each button on the RMT-16IR remote control will toggle between the “A” and “B” sources for each input. Please use the information below when selecting the desired source for eac
Краткое содержание страницы № 13
RMT-16IR REMOTE CHANNEL CONFIGURATION Why would I need to change the remote channel? In some instances, the 8x4 CAT-5 Matrix for HDMI may use IR codes that confl ict with other IR remote control devices. The unit may switch inputs when another brand IR remote control is used or the RMT-16IR may cause other brand IR controlled devices to behave unexpectedly. I am experiencing the issues listed above. What do I do? In these cases it is recommended to change the IR channel that the RMT-16IR rem
Краткое содержание страницы № 14
EDID MANAGEMENT FEATURE EDID. What is it and what is it used for? Under normal circumstances, a source device (digital and analog) will require information about a connected device/display to assess what resolutions and features are available. The source can then cater its output to send only resolutions and features that are compatible with the attached device/ display. This information is called EDID (Extended Display Information Data) and a source device can only accept and read one EDID
Краткое содержание страницы № 15
EDID MANAGEMENT OPTIONS v. 3019 EDID Modes The diagram below illustrates the 8 DIP switch bank. DIP SWITCH Function 1 EDID Mode 2 EDID Mode 3 IR Channel 4 IR Channel 5 EDID Mode 6 N/A 1 3 5 7 2 4 6 8 7 EDID Mode 8 N/A Use DIP switches 1, 2, 5, and 7 to select the desired EDID management mode. EDID Mode 0 (Switch 1=OFF Switch2=OFF Switch5=ON) • EDID is copied from the device connected to the fi rst active hdmi output port. • All features newer that HDMI 1.2 are cleared. EDID Mode 1 (Switch 1=ON Sw
Краткое содержание страницы № 16
LED ARRAY DESCRIPTION The LED array on the 8x4 CAT-5 Matrix for HDMI is designed to inform the user of the current source to output routes. Each output has a 4 LED array that will indicate which source is currently selected. Each input can accept two sources and therefore the LED array will act differently according to which input, “A” or “B”, is active for each. • An input’s “A” source will be indicated by an single LED (the selected “A” input) that is ON. • An input’s “B” source will be i
Краткое содержание страницы № 17
8X4 CAT-5 MATRIX FOR HDMI RS-232 SERIAL COMMUNICATION What features are available via the RS-232 serial communications port? The 8x4 CAT-5 Matrix for HDMI can accept commands through the RS-232 serial communications port located on the rear panel. The current RS-232 control features are: • Switching/routing of inputs to outputs without the RMT-16IR remote control. • Switch EDID management modes without opening the unit to physically modify DIP switches. • Print matrix routing state. How do I
Краткое содержание страницы № 18
8X4 CAT-5 MATRIX FOR HDMI RS-232 COMMANDS Switching/Routing Binary Table ASCII ASCII Input Output Input Output Command Command A1 or a1 1A 1 C1 or c1 1A 3 A2 or a2 1B 1 C2 or c2 1B 3 A3 or a3 2A 1 C3 or c3 2A 3 A4 or a4 2B 1 C4 or c4 2B 3 A5 or a5 3A 1 C5 or c5 3A 3 A6 or a6 3B 1 C6 or c6 3B 3 A7 or a7 4A 1 C7 or c7 4A 3 A8 or a8 4B 1 C8 or c8 4B 3 B1 or b1 1A 2 D1 or d1 1A 4 B2 or b2 1B 2 D2 or d2 1B 4 B3 or b3 2A 2 D3 or d3 2A 4 B4 or b4 2B 2 D4 or d4 2B 4 B5 or b5 3A 2 D5 or d5 3A 4 B6 or b6
Краткое содержание страницы № 19
RECEIVER PANEL LAYOUT Front Panel 3 124 Back Panel 6 5789 Top Panel 10 16
Краткое содержание страницы № 20
RECEIVER PANEL DESCRIPTIONS 1 IR Relay Receiver This receiver will receive commands from the included IR remote control and from other commercial IR remote controls and relay it back to the optional IR blaster. This is intended for remote control of devices connected to the 8x4 CAT-5 Matrix for HDMI from the extended location. 2 Equalization Trim Pot When the receiver is set to manual equalization (see page 21), this will control the amount of EQ compensation applied to the video signal for
