Краткое содержание страницы № 1
n
120 mm (4-3/4") MODEL UMl2OOD
120 mm (4-314") MODEL UMlZOODW
With Fast Charger
INSTRUCTION MANUAL
SPEC I F I CAT I 0 N S
Model UM1200D
Effective cutting width I No load speed I Dimensions IL x W x H) I Net weight
361 mm x 126 mm x 773 mm
120 mm 14 314 'I 1 13,000 Rimin 1 kg 12 2 lbsl
I14 114" x 5" x 30 318")
1 1
Battery Cartridge 7000 Model DC7100 Fast charger
Charging
Dimensions Net
Voltage
input output
time IL XW x HI weight
A.C. only 145 mm x 80 mm x 61 mm 0.7 kg
"" 1 lHr
Краткое содержание страницы № 2
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFE- TY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PER- SONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. Be aware that this appliance is always in an operating condition, because it does not have to be plugged into an electrical outlet. 2. Avoid Dangerous Environment - Don't use or leave appliances in damp or wet locations. 3. Don't Use I
Краткое содержание страницы № 3
IMPORTANT SAFETY INSTRUCTIONS I. SAVE THESE INSTRUCTIONS - This manual Length of Cord (Feet) 25 50 100 150 AWG Size of Cord 18 18 18 16 9. Do not operate charger with damaged cord or plug - replace them im- mediately. IO. Do not operate charger if it has received a sharp blow, been dropped, or other- wise damaged in any way; take it to a qualified serviceman. 11. Do not disassemble charger or battery cartridge; take it to a qualified serviceman when service or repair is required. Incorr
Краткое содержание страницы № 4
ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C (5OOF) or ABOVE 4OoC (104OF). 2. Do not attempt to use a step-up transformer, an engine generator or DC power receptacle. 3. Do not allow anything to cover or clog the charger vents. 4. Do not short the battery cartridge: (1 1 Do not touch the terminals with any conductive material. (2) Avoid storing battery cartridge in a container with other metal objects such as
Краткое содержание страницы № 5
ASSEMBLY CAUTION : removed before assembling the trimmer. Always be sure that the battery cartridge is I 0 Remove the wing bolt from the motor f I housing. Insert the shaft into the motor housing, align the hole in the shaft with the hole in the motor housing. Replace the wing bolt and tighten it securely. / Wing bolt Fig. 1 .Remove the wing bolt from the grip. Insert the shaft into the grip, align the I I hole in the shaft with the hole in the grip. Replace the wing bolt and tig
Краткое содержание страницы № 6
Installing or removing battery cartridge 0 Always switch off the tool before insertion or removal of the battery cartridge. .To remove the battery cartridge, pull out the set plate on the bottom of the tool and grasp both sides of the cartridge while withdrawing it from the barrel. .To insert the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Snap the set plate back into place. Be sure to close the set plate fully bef
Краткое содержание страницы № 7
Installing or removing blade CAUTION : Always be sure that the battery cartridge is removed before installing or removing blade. 0 Insert the blade into the groove in the blade holder until the blade is held by the two protrusions on the blade holder. Fig. 7 CAUTION : Always be sure that the blade is installed properly before operation. 0 To remove the blade, bend both ends of the blade up until it will slip up and over the protrusions. Then pull the blade out. Fig. 8 CAUTION : Rep
Краткое содержание страницы № 8
Switch action Lock-off lever .To prevent the trigger from being acci- dentally pulled, a lock-off lever is pro- vided as a safety feature. To start the tool, slide the lock-out lever in the direction of the arrow and pull the trigger. Release the trigger to stop. CAUTION : Before inserting the battery cartridge into the tool, always check to see that the trigger switch actuates properly and re- turns to the "OFF" position when re- leased. Fig. 10 Operation .Hold the tool firmly w
Краткое содержание страницы № 9
CAUTION : Forcing the tool may shorten the operating time per battery charge. If the tool is operated continuously until the battery cartridge has discharged, allow the tool to rest for 15 minutes before proceeding with a fresh battery. NOTE : You can expect up to 35 minutes running time on a single charge. MA1 NTENANCE CAUTION : Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection .or maintenance. Cleaning blade and
Краткое содержание страницы № 10
ACCESSORI ES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. 0 Makita Battery cartridge 7000 0 Blade (20 per pkg.) Part No. 632003-2 Part No. 792374-0 0 Fast charger (Model DC7100) 0 Battery holster Holster holds extra battery. Part No. 823033-3C
Краткое содержание страницы № 11
Sep.-12-'85 EN I 120 mm (4-3/4") CORDLESS GRASS TRIMMER @-- Model UM1200D Note: The switch and other part configurations may differ from country to country. 11
Краткое содержание страницы № 12
MODEL UM1200D Sep.- 12-’85 EN ,& DESCRIPTION ,,!& DESCRIPTION 1 1 Compression Spring 3 11 1 Pipe 18 lShaft1 12 1 Motor Housing R 2 1 Lock off Lever 3 1 Grip R 13 1 Motor 4 1 Swwh 14 1 Motor Housing L 5 1 Switch Lever 15 1 Wing Bolt M4x30 Blade Holder 6 1 Grip L 16 1 I 1 Wing Bolt M4x30 17 1 Safety Guard 8 1 Name Plate 18 8 Tapping Screw 3x20 19 1 Tube 4 Guard Ring1 9 1 Set Plate 10 1 Battery Holder MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly
