Руководство по эксплуатации Flymo EasiCut 510

Краткое содержание страницы № 1

EasiCut 420/EasiCut 450/
EasiCut 510
EasiCut 600XT
EasiCut 420/450/510
EasiCut 600XT
For all customer enquiries or for replacement parts, contact:-
☎ ☎ 0870 609 1901
www.flymo.com
customer.services@husqvarna.co.uk
IMPORTANT INFORMATION
Read before use
& retain for future reference

Краткое содержание страницы № 2

Carton Contents EasiCut 420/450/510 Handguard blade cover instruction manual belt clip EasiCut 600XT Handguard blade cover instruction manual belt clip IMPORTANT ! Please check the contents of the carton are correct BEFORE assembling your new product. IF ANY PARTS ARE MISSING CONTACT:- Husqvarna Outdoor Products Customer Service Department direct Telephone : 0870 609 1901 Fax : 0870 609 1902 Safety If not used properly this product can be dangerous! This product can cause serious injury to the

Краткое содержание страницы № 3

Safety General 3. Before using the machine and after any impact, 1. Never allow children or people unfamiliar with these check for signs of wear or damage and repair as instructions to use the Hedgetrimmer. Local regula- necessary. tions may restrict the age of the operator. 4. Always ensure the hand guard supplied is fitted 2. Only use the Hedgetrimmer in the manner and before using the Hedgetrimmer. Never attempt for the functions described in these instructions. to use an incomplete Hedgetr

Краткое содержание страницы № 4

CABLES 1. No earth required. Our products are double IMPORTANT insulated to EN50144 and under no circum- 2 • Use only 1.00mm size cable up to 40 metres stances should an earth be connected to any length maximum. part of the product. Maximum rating : 2. Ensure the mains voltage suits your product 2 1.00mm size cable, 10 amps 250 volts AC. 3. IMPORTANT! • YOUR HEDGETRIMMER IS SUPPLIED The wires in the mains lead are coloured in WITH CABLE WIRED DIRECTLY INTO THE accordance with the follow

Краткое содержание страницы № 5

Before Use B1 B2 B3 C1 C2 D Before starting your Hedgetrimmer. 4. Form a loop in the mains cable and push the loop • Securing the cable in the Belt Clip helps keep through the hole in the Belt Clip (C1) ensuring the the cable away from blade. coil in the cable is close to the clip. 1. Push up the hook on the Belt Clip (B1) 5. To secure, position the loop over the hook and 2. Place the rear section of the Belt Clip behind pull back (C2). your belt (B2) 6. Connect to mains and switch on 3. Push do

Краткое содержание страницы № 6

How to Use How to Use your Hedgetrimmer M 1. Inspect area to be cut before each use - remove objects which can be thrown or become entangled in the cutting blades. 2. Always keep the Hedgetrimmer in front of your body. Hold handle firmly with both hands and stand in a secure and stable position. 3. Allow the cutting blades to reach full speed before entering the material to be cut. 4. Always work going away from people and solid objects such as walls, large stones, trees, vehicles etc. 5. If bl

Краткое содержание страницы № 7

Fault Finding Hints Fails to Operate Fails to stop when one switch lever is released. 1. Is the Power Turned On? Immediately disconnect from the mains 2. Check the fuse in the plug, if blown replace. electricity supply and consult your local 3. Fuse continues to blow? approved Service Centre. Immediately disconnect from the mains Poor cut quality electricity supply and consult your local 1. Ensure the product is being used correctly approved Service Centre. (see How to Use) Cutting blade stops u

Краткое содержание страницы № 8

Service Recommendations 1. We strongly recommend that your product is plete machine including cable and any extension serviced at least every twelve months, more often cables used. in a professional application. A network of specialist dealers can be found in your 2. Always use genuine Flymo Spare Parts. local Yellow Pages. To obtain service on your product 3. Prepacked spares are available from most Flymo simply telephone or visit your local Service Centre. Approved stockists. Should you requi