Краткое содержание страницы № 1
AT&T
®
PARTNER Plus
Communications System
Release 3
Installation
Краткое содержание страницы № 2
AT&T 518-455-213 Copyright © 1992 AT&T Issue 1 All Rights Reserved June 1992 Printed in U.S.A. Notice Every effort was made to ensure that the information in this book was complete and accurate at the time of printing. However, information is subject to change. Federal Communications Commission (FCC) Interference Notice This equipment has been tested and found to comply with the limits of a Class A digital device, pursuant to Part 15 of FCC rules. These limits are designed to provide reasonable
Краткое содержание страницы № 3
Contents ii Important Safety Instructions 1 Overview 2 An Example System Setup 4 Required Parts Installation Guidelines 5 ■ Telephones and Devices 5 ■ Combination Extensions 6 Using A Direct Connection 6 6 Using a Bridging Adapter 7 Installation Procedures ■ Installing the Control Unit and Modules 7 ■ 9 Connecting Lines and Extensions ■ 11 Connecting Caller ID Display Units ■ 12 Assembling System Phones 12 Desk Mounting Wall Mounting 13 ■ Connecting and Testing Telephones 14 ■ Connecting Paging,
Краткое содержание страницы № 4
Important Safety Instructions Always follow these basic safety precautions when using the system: 1. Read and understand all instructions. 2. Follow all warnings and instructions marked on the product. 3. Never spill liquid on the product or drop objects into the ventilation slots and openings. Doing so may result in serious damage to the components. 4. Repair or service must be performed by a qualified repair person. 5. The product is provided with a three-wire grounding type plug. This is a sa
Краткое содержание страницы № 5
Installation Overview This guide explains how to install the system. It begins with an example system setup, then follows with an illustration of the components you need to install the system and general guidelines to consider before installation. Next, it provides step-by-step instructions for connecting and testing the components for initial installation and upgrades. Finally, it ends with important system specifications and requirements. If your company already has modular jacks for all outsi
Краткое содержание страницы № 6
An Example System Setup The next page shows a control unit with two 206 modules and Extensions two 400 modules, giving the system a capacity of 12 outside Various devices—including system phones and industry- lines and 12 extensions. Although your system may differ, this standard devices—can be connected to the modular wall example will give you an idea of the types of equipment you jacks. The modular wall jacks connect to the extension jacks can connect to it. In the example, system phones and
Краткое содержание страницы № 7
CONTROL UNIT EXTENSIONS Extension 10 Extension 18 Extension 17 Extension 11 Extension 16 Extension 15 Extension 12 Extension 13 Extension 14 An Example System Setup 3
Краткое содержание страницы № 8
Required Parts You will have up to three types of system component packages; Figure 1 shows the contents of each package in the area marked by a dashed line. Check your packages to be sure you have the parts shown here (if not, call the appropriate support telephone number as instructed on the inside front cover). Control Unit MLS-34D Programming Overlay MLS-18D/MLS-12D Programming Overlay Quick Reference Cover Processor Backplane Cards Module AC Power Cord 400 Module 206 Module 7-foot Telephone
Краткое содержание страницы № 9
Installation Guidelines Telephones and Devices You can connect the following telephones and devices to the system: ■ MLS- and MLC-Model System Phones. System phones require at least two-pair wiring and are compatible with AT&T 4-pair SYSTIMAX™ wiring. ■ Call Assistant Intercom Autodialers with Busy Indication (MLS-CA24). You can connect an Intercom Autodialer to the system phone at extensions 10 and 11 (maximum two per system). The Intercom Autodialer has its own power supply, which must be plug
Краткое содержание страницы № 10
Combination Extensions You can connect a standard device (such as a standard phone or an answering machine) on an extension by itself, or so that it shares an extension with another piece of equipment (either another standard device or a system phone). An extension with two devices connected to it is called a combination extension. You cannot install two system phones on the same extension, and the combined REN (Ringer Equivalence Number) of two devices on one extension cannot exceed 2.0. (The R
Краткое содержание страницы № 11
Installation Procedures Before installing the system, be sure you read the safety instructions on page ii. WARNING: There are no customer-serviceable components inside the system modules or backplane. There are hazardous voltages within that can cause severe or fatal personal injury. DO NOT OPEN THE MODULES. Installing the Control Unit and Modules Install the control unit’s backplane within five feet (1.5 meters) of a properly grounded AC electrical outlet (not controlled by a switch) and the ne
Краткое содержание страницы № 12
4 A) To power down the control unit, pull out the main Main Circuit Breaker circuit breaker on the control unit. On a PARTNER Plus 220V system, move the Power Jack on/off switch to the “off” position (“O”). B) Press the AC power cord firmly into the power jack on the top right side of the backplane until it locks into place. Plug the other end of the power cord into a C) properly grounded three-prong wall outlet not controlled by a switch. To power up the control unit, push in the main D) circu
Краткое содержание страницы № 13
Connecting Lines and Extensions If extensions are not wired to any modular jacks, call a 555-1343 qualified service technician. 555-1344 A) Test for dial tone at the network interface jacks 1 555-1345 before connecting outside lines to the control unit. For the test, connect a standard phone 555-1346 to the first network interface jack. Network Interface B) Lift the handset and listen for dial tone. (If there Jacks is no dial tone, contact your local telephone company before continuing.) Repeat
Краткое содержание страницы № 14
A) Connect modular telephone cords to 206 module 5 extension jacks, starting at the top extension jack on the leftmost module. B) Route each cord through the hook on the front of the module, and then push the cords through the space below the module and out through the back. Pull the cords from behind the backplane, C) leaving at least two feet of slack to allow easy replacement of system modules (for future maintenance so you can easily reconnect cords after replacing system modules). D) Connec
Краткое содержание страницы № 15
Connecting Caller ID Display Units To get Caller ID information for an extension, you must first subscribe to the service (on a per-line basis) from your local telephone company, then connect the units as described here. You must connect the Caller ID display unit directly to the line that supports Caller ID at the network interface jack. Additionally, you must provide a separate wiring run for the unit to the appropriate location. To have additional wiring runs installed, call a qualified servi
Краткое содержание страницы № 16
Assembling System Phones You can either desk mount or wall mount a system phone. If the system phone is manufactured with a separate stand, you can use the stand to either wall mount the phone or raise the angle of the phone when desk mounting. (The stand is required for MLS-34D phones.) Alternatively, some system phones—such as the MLS-18D—are manufactured with a fixed stand. Any instructions below for installing the stand do not apply to this type of phone. (Wall mounting is not recommended fo
Краткое содержание страницы № 17
Wall Mounting If you wall mount a display phone, the display may be difficult to read, so desk mounting is recommended. (Wall mounting instructions apply to corded MLS-model phones only. To wall mount an MLC-6 cordless phone, follow the instructions in the booklet provided with the phone.) Wall Mounting Phones with Separate Stands Reverse the plastic hook that sits in the earpiece part 1 of the handset cradle. A) To install the telephone stand, gently place the 2 phone upside down with the low e
Краткое содержание страницы № 18
A) Unscrew the phone’s four mounting screws and lift 2 the base of the phone off the top. CAUTION: Do not touch electrical circuitry. To do so Mounting Screws will expose you to a risk of electrical shock and possibly damage the equipment. B) Turn the base of the phone upside down so that the phone base can be mounted parallel to the wall—and then place it back on the base. C) Replace the four mounting screws. A) Insert the phone cord through the center of the 3 stand and plug it into the jack l
Краткое содержание страницы № 19
Connecting Paging, Music-On-Hold, and Call Reporting (SMDR) Devices Only steps for connection to the processor module are provided here. Refer to Chapter 4 of the PARTNER Plus Programming and Use guide and the manufacturer’s instructions for additional information on installing, PAGE Jack programming, and using these devices. Paging System 1 Insert the modular plug into the PAGE jack on the processor module. 2 Route the cord as you did for line and extension cords, then connect it to the paging
Краткое содержание страницы № 20
Connecting Intercom Autodialers Since the autodialer has a fixed stand, you may need to adjust the height of the system phone—by installing a stand—to match the height of the autodialer. Refer to Step 2 of “Desk Mounting” under “Assembling System Phones” for instructions. You can wall mount an Intercom Autodialer to work next to a wall-mounted system phone; however, wall-mounting system display phones is not recommended. A) Unplug the phone’s modular telephone cord from 1 the jack on the bottom
