Краткое содержание страницы № 1
Краткое содержание страницы № 2
Краткое содержание страницы № 3
Contents 1. INTRODUCTION ........................................................................................................5 Features..........................................................................................................................5 Software Features ..........................................................................................................6 Package Contents ...................................................................................
Краткое содержание страницы № 4
Trunk Configuration........................................................................................30 Port Mirroring Configuration...........................................................................31 VLAN Configuration .......................................................................................33 VLAN Configure......................................................................................33 Create VLAN Group.................................................
Краткое содержание страницы № 5
TFTP Configuration........................................................................................69 Update Firmware ....................................................................................70 TFTP Restore Configuration...................................................................70 TFTP Backup Configuration ...................................................................71 X-modem Upgrade ..........................................................................
Краткое содержание страницы № 6
Per Port Configuration................................................................................. 104 Port Mirroring...................................................................................................... 105 SNMP Management ........................................................................................... 107 Security Manager ............................................................................................... 108 802.1X .............................
Краткое содержание страницы № 7
1. Introduction The TEG-S3000i chassis switch is a modular switch that can be used to build high-performance switched workgroup networks. This switch is a store-and-forward device that offers low latency for high-speed networking. The Switch is designed for workgroup, department or backbone computing environments. The TEG-S3000i chassis switch features a “store-and-forward “ switching scheme. This allows the switch to auto-learn and store source address in an 8K-entry MAC address
Краткое содержание страницы № 8
High back-plane bandwidth 8.8Gbps Support IEEE802.3ad Port trunk with LACP Broadcast storm filter supported Stack management via one IP address, easy management by Web GUI IGMP support for Multi Media application Support IEEE 802.1p class of service Port security supported Port bandwidth control supported Support IEEE 802.1d Spanning tree protocol Supports GVRP function Port-Based VLAN and 802.1Q VLAN supported IEEE 802.1X user authentication Broadcast storm filter su
Краткое содержание страницы № 9
RFC 1157 SNMP, RFC 1213 MIB II, RFC 1643 Ethernet RFC Standard like, RFC 1493 Bridge MIB, RFC 1757 RMON 1, RFC 1215 Trap, RFC 2674 VLAN MIB, private MIB Cold start, link down, link up, authorization fail, fan fail trap. SNMP Trap Trap station up to 3 Support IEEE802.3ad with LACP function and provide Port Trunk 7-trunk group of 4 member ports within 26 ports Spanning Tree IEEE802.1d spanning Tree Port based VLAN IEEE802.1Q Tag VLAN VLAN IEEE802.1v Protocol VLAN (IP, IPX) Static VL
Краткое содержание страницы № 10
MAC address filter for ingress and egress packet Port Security Static MAC address lock for source address Global system supports 3 mirroring types: “RX, TX and Port Mirror Both packet”. The maximum of port mirror entries is up to 25 Bandwidth Control Per port support Bandwidth control. Per level 100K The switch provide Stack Grouping feature and through master switch interface can manage and stack up to 8 Stacking units. Support IEEE802.1x User-Authentication and can report to RADI
Краткое содержание страницы № 11
Rack-mounted kit User Guide TEG-S3000i chassis switch Four Rubber Feet RS-232 Cable Rack-mounted Kit Power Cord User Guide CD-ROM Figure 1-2. Package Contents Compare the contents of your TEG-S3000i chassis switch package with the standard checklist above. IF any item is missing or damaged, please contact your local dealer for service. Ethernet Switching Technology Ethernet Switchi
Краткое содержание страницы № 12
Auto-negotiation regulates the speed and duplex of each port based on the capability of both devices. Flow-control allows transmission from a 100Mbps node to a 10Mbps node without loss of data. Auto-negotiation and flow-control may need to be disabled when networking with legacy equipment. Disabling the auto-negotiation is accomplished by fixing the speed or duplex of a port. Ethernet Switching Technology supplied higher performance at costs lower than other solutions. Wider bandwidth
Краткое содержание страницы № 13
2. Hardware Description This Section mainly describes the hardware of the TEG-S3000i chassis switch, and gives a physical and functional overview of the switch. Physical Dimension The TEG-S3000i chassis switch physical dimension is 440mm(W) x 280mm(D) x 44mm(H). Front Panel The Front Panel of the TEG-S3000i chassis switch consists of 3 10/100Mbps module slots. One Gigabit module slot is located at the rear-panel of the switch.
Краткое содержание страницы № 14
Off Power is not connected Green The port is connecting with the device. LNK/ACT Blinks The port is receiving or transmitting data. Off No device attached. Orange The port is operating in Full-duplex mode. FDX/COL Blinks Collision of Packets occurs in the port. Off In half-duplex mode Table 2-1. The Description of LED Indicators Rear Panel A module slot, 3-pronged power plug, 2 fans, a power switch button, and a console port are located at the rear Panel of
Краткое содержание страницы № 15
Attaching Rubber Feet A. Make sure mounting surface on the bottom of the Switch is grease and dust free. B. Remove adhesive backing from your Rubber Feet. C. Apply the Rubber Feet to each corner on the bottom of the Switch. These footpads help prevent the Switch from shock/vibration. Rack-mounted Installation The TEG-S3000i chassis switch comes with a rack-mounted kit that can be mounted in an EIA standard size, 19-inch Rack. The Switch can be placed in
Краткое содержание страницы № 16
power indicator on the front panel to see if power is properly supplied. 14
Краткое содержание страницы № 17
3. Network Application This section provides you a few samples of network topology in which the Switch is used. In general, the TEG-S3000i chassis switch is designed as a segment switch. That is, with its large address table (8000 MAC address) and high performance, it is ideal for interconnecting networking segments. PC, workstations, and servers can communicate with each other by directly connecting to the TEG-S3000i chassis switch. The switch automatically learns node addresses,
Краткое содержание страницы № 18
Stacking Workgroup Stackable technology unites up to eight individual stackable switches into a single logical unit using cables and stacking software. The stack behaves as a single switching unit that is managed by a master switch. The master switch automatically creates and updates all the switching tables. A working stack can accept new members or delete old ones without service interruption Each switch in the stack has the capability to behave as a master or su
Краткое содержание страницы № 19
The stackable switch (Master) Cable connection (Cat. 5 cable) The stackable switch (Slave 01) Cable connection (Cat. 5 cable) The stackable switch (Slave 02) Can units up to 8 stackable switches The stackable switch (Slave 08) Figure 3-2. A stacking workgroup application Connecting to the Switch The Console port is a female DB-9 connector that enables a connection to a PC or terminal for monitoring and configuring the Switch. Use the supplied RS-232 cabl
Краткое содержание страницы № 20
4. Console Management Login in the Console Interface When the connection between the Switch and PC is ready, turn on the PC and run a terminal emulation program or Hyper Terminal and configure its communication parameters to match the following default characteristics of the console port: Baud Rate: 9600 bps Data Bits: 8 Parity: none Stop Bit: 1 Control flow: None Figure 4-1. The settings of communication parameters After finishing the paramet
