Краткое содержание страницы № 1
MOSFET POWER AMPLIFIERS
Installation Instructions / Owner's Manual
100SX 200SX 400SX 600SX
800SX 1200SX 440SX 640SX
Краткое содержание страницы № 2
INTRODUCTION Congratulations on your purchase of a California state-of-the-art power amplifier. Your selection of a California car audio product indicates a true appreciation of fine musical reproduction. Whether adding to an exi sting system or including your California amplifier in a new system, you are certain to notice immediate performance benefits. KEEP YOUR SALES RECEIPT Take this time to attach your sales receipt to the manual and put in a safe place. In case of any unforeseen re
Краткое содержание страницы № 3
SAFETY PRECAUTIONS Fuse amplifier’s power wire at the battery. Be sure to fuse the power wire within 12” of the car's battery. This will protect the car's battery in case of a short circuit between the power amplifier and battery. THIS IS A MUST, the amplifier's built-in fuse will only protect the power amplifier not the car's battery! Use high grade wire connectors. To ensure maximum power transfer and secure safe connections, it is recommended to use high grade barrier spades (for conne
Краткое содержание страницы № 4
FEATURES AND BENEFITS DC Offset Protection This circuit protects the output of the amplifier against DC voltage. If for some reason DC voltage is detected at the output stage, the amplifier will shut down protecting the speakers from direct current. Short Circuit Protection The circuit protects the amplifier from damage due to a short found in the speakers or wiring. If one of the speakers or its wiring comes in contact with ground, the amplifier will shut down. To resume normal operation
Краткое содержание страницы № 5
Bass Boost For added low frequency performance the two channel amplifiers are equipped with 12dB bass boost. Power Fusing This protects the amplifier against short circuits and excessive current. Remote Turn-on Automatically turns amplifier on when connected to the head unit's remote output. The amplifier will turn on and off with the head unit to save current consumption. This control also operates the reset circuit for the amplifier's protection. It must be connected with the head unit
Краткое содержание страницы № 6
MOUNTING LOCATION Before you start the installation, it will be necessary to find a mounting location for the amplifier. Find a location in which the amplifier will receive adequate ventilation in order to dissipate the heat it develops during operation. Two popular mounting locations are in the trunk or under the seat. Select the location in which you wish to mount the amplifier. Use caution when mounting amplifier, there are many wires, gas lines, vacuum lines, brake lines as well a
Краткое содержание страницы № 7
POWER CONNECTIONS B + REM GND L + L - R + R - FUSE BRIDGED I IN N- -L LI IN NE E P PO OW WE ER R F FU US SE E M MO OU UN NT TE ED D W WI IT TH HI IN N 1 12 2" " R RA AD DI IO O' 'S S R RE EM MO OT TE E F FR RO OM M B BA AT TT TE ER RY Y R RE EC CO OM MM ME EN ND DE ED D T TU UR RN N- -O ON N O OU UT TP PU UT T ( (N NO OT T P PR RO OV VI ID DE ED D) ) - - + + 9 94 4..7 7 C CA AR R B BA AT TT TE ER RY Y + +1 12 2V V IMPORTANT! Before making any connections, disconnect the car’s battery until the
Краткое содержание страницы № 8
SIGNAL CONNECTIONS Connect the output of the head unit (AM/FM cassette player, CD, or DAT) to the RCA input terminals of the amplifier. To make these connections, we recommend high quality RCA cables, which are available at your local car audio retailer. Run signal wires away from electrical wires to avoid possibility of induced noise from the car's electrical system (i.e. popping noises or engine noise). Please note that when making these connections the signal inputs correspond with the
Краткое содержание страницы № 9
HIGH LEVEL CONNECTIONS (OPTIONAL) If a low level RCA signal source is not available, you may still wire the models 100SX, 200SX, and 400SX with high-level or speaker level outputs from your head unit. However, only speaker leads from a "floating ground" system may be used (see diagram below). Use the strip connector located on the end of the amplifier to make this connection. The strip connector should be connected with the front or rear, 2 channels of your head unit. Note: The speaker
Краткое содержание страницы № 10
SPEAKER CONNECTIONS Make the speaker connections using speaker wire that is at least 16 gauge or heavier. As with any audio component, proper phasing of the amplifier and speakers is essential for strong bass response. When connecting, make sure that positive (+) from the amplifier is connected to the positive (+) of the speaker, and the same for negative (-). B + REM GND L + L - R + R - FUSE BRIDGED - - + + - - + + 4 4 O Oh hm m S Sp pe ea ak ke ers rs (2 (2 O Oh hm m M Min inim imu um m) )
Краткое содержание страницы № 11
SPEAKER CONNECTIONS (BRIDGED) The California amplifiers are capable of being bridged in a mono configuration. This feature allows you the flexibility of using the amplifier to drive a ** subwoofer or a center channel. In this configuration the amplifier sums the right and left channel to deliver one channel (mono) output. Please note: in order for the amplifier to sum right and left signal information, both right and left RCA connections must be made. **CAUTION! In the bridged mode, the am
Краткое содержание страницы № 12
-- ++ ++-- SPEAKER CONNECTIONS (TRI-MODE) The amplifier is capable of running in a Mono / Stereo mode. This feature gives the amplifier the ability to run stereo satellites (midbass & tweeter) simultaneously with a mono subwoofer. These connections are more complicated because they require the use of passive crossover networks (Not provided) to divide the frequencies to the speakers. We have included a sample diagram for 4 Ohm connections. If you wish to use multiple speakers to achieve a
Краткое содержание страницы № 13
SETTING THE CROSSOVER AND BASS BOOST Select your crossover type and frequency. . (Please note: If you intend to use the amplifier in the Tri-mode configuration, it is necessary to set the crossover control to the “Flat” setting in order to receive full range output) The California amplifiers are equipped with a built-in variable crossover network allowing you to select the crossover type (i.e. Low-Pass or Hi-Pass) and the desired crossover point. For example if you wish to drive a pair of s
Краткое содержание страницы № 14
TROUBLE SHOOTING THE SYSTEM We have put together this trouble-shooting guide if you experience problems after installing the amplifier. Please keep in mind that the majority of problems incurred are caused by improper installation and not the equipment itself. In addition, there are many components in the system that could cause various signal problems such as inducted electrical noise and engine noise. Before you can properly address the problem, you must first find the component that is
Краткое содержание страницы № 15
SPECIFICATIONS 100SX Output Power @ 4 Ohm..................................................2 x 70 WATTS RMS Power @ 4 Ohm ....................................................2 x 35 WATTS RMS Power @ 2 Ohm ....................................................2 x 50 WATTS Bridged RMS @ 4 Ohm..................................................1 x 100 WATTS THD @ RMS Power ........................................................................<0.07% Frequency Response..................................
Краткое содержание страницы № 16
600SX Output Power @ 4 Ohm.................................................2 x 300 WATTS RMS Power @ 4 Ohm....................................................2 x 150 WATTS RMS Power @ 2 Ohm ...................................................2 x 225 WATTS Bridged RMS @ 4 Ohm..................................................1 x 450 WATTS THD @ RMS Power ........................................................................<0.07% Frequency Response.................................................
Краткое содержание страницы № 17
440SX Output Power @ 4 Ohm .................................................4 x 100 WATTS RMS Power @ 4 Ohm ....................................................4 x 50 WATTS RMS Power @ 2 Ohm ....................................................4 x 75 WATTS Bridged RMS @ 4 Ohm..................................................2 x 150 WATTS THD @ RMS Power ........................................................................<0.07% Frequency Response................................................
Краткое содержание страницы № 18
LIMITED WARRANTY Profile Consumer Electronics, Inc. warrants this product to be free from defects in material and workmanship for a period of One (1) Year from the date of sale to the original consumer purchaser. If this product is proven to be defective within this one year period, Profile will repair it when said product is returned, with a copy of the dated sales receipt, freight prepaid to Profile. This warranty is valid only in the United States.
Краткое содержание страницы № 19
WARRANTY REPAIR POLICY In the unlikely event of product failure, the following procedures should be followed 1) The unit must be under the 1-year warranty period. 2) The unit must have no physical damage. 3) A copy of the original proof of purchase must be sent with the unit. 4) Include a brief description of the problem or failure with the unit. 5) Include the return street address and daytime telephone number. 6) Allow 2~3 weeks for rep
Краткое содержание страницы № 20
By PROFILE CONSUMER ELECTRONICS, INC. 15060 SHOEMAKER AVE SANTA FE SPRINGS, CA 90670 TEL: (562) 404-9393 FAX: (562) 404-9433 WWW.PROFILEUSA.COM
