Краткое содержание страницы № 1
P1-600.2 / P1-1000.2
P1-600.4 / P1-1000.4
P1-2000.1 / P1-5000.5
Краткое содержание страницы № 2
POWER ONE SERIES AMPLIFIERS The Power One Series products have been designed to a very high level of performance, with features unavailable in any other product. All of the amplifiers have variable crossovers built in, with added touches such as subsonic filter, bass equalization and a remote Level control module (some models) that allows subwoofer Level control from the drivers seat. To ensure years of listening pleasure, all amplifiers have a built in diagnostic mode that will detect shorte
Краткое содержание страницы № 3
WIRE GAUGE GENERAL INSTALLATION PROCEDURE System Design The success of any car stereo system relies on several factors, such as the system design, execution of the installation, and system setup. Please remember that any system is only as good as its weakest link. Please remember that higher power systems are not necessarily useful purely for high sound pressure levels, but also to establish a headroom capability, to reproduce musical peaks cleanly without distortion. Lower power amplifiers w
Краткое содержание страницы № 4
AMPLIFIER FEATURE DESCRIPTIONS POWER ONE AMPLIFIERS: ! Each model is capable of 4 & 2-Ohms stereo per channel, or 4-Ohms mono bridged operation except the mono amps ! All Crunch amplifiers feature a comprehensive diagnostic system, with speaker lead short circuit, and amplifier DC which are capable of 4, 2 and 1-Ohm loads. faults indicated by the red “PROTECT” LED. ! The input sensitivities for rated output powers are variable from 0.2V to 6V on all models. ! CAUTION: DO NOT OPERATE ANY AMPLIF
Краткое содержание страницы № 5
- + - + - + - + L L L L LEVEL BASS EQ HPF LPF X-OVER MODE LEVEL BASS EQ HPF LPF + - gnd - + X-OVER MODE + - gnd - + HI INPUT 6V 0.2V 0dB 12dB 60Hz 12KHz 30Hz 250Hz HI INPUT FULL LPF HPF MONO STEREO 6V 0.2V 0dB 12dB 60Hz 12KHz 30Hz 250Hz FULL LPF HPF MONO STEREO R R R R LINE OUT LINE INPUT LIN
Краткое содержание страницы № 6
- + - -+ - + - -+ - + - + - + - + HIGH INPUT HIGH INPUT MODE X-OVER MODE X-OVER X-OVER X-OVER + - GND - + + - GND - + + - GND - + + - GND - + CH1 CH3 CH1 CH3 2 3 4 2 3 4 LPF HPF FULL FULL HPF LPF LPF HPF FULL FULL HPF LPF CH1 CH2 CH3 CH4 CH1 CH2 CH3 CH4 LPF HPF BASS EQ LEVEL LEVEL BASS
Краткое содержание страницы № 7
- + - -+ - + - + - + - + HIGH INPUT MODE X-OVER X-OVER + - GND - + + - GND - + L L CH1 CH3 LEVEL BASS EQ HPF LPF X-OVER MODE 2 3 4 LPF HPF FULL FULL HPF LPF CH1 CH2 CH3 CH4 + - gnd - + LPF HPF BASS EQ LEVEL LEVEL BASS EQ HPF LPF HI INPUT 6V 0.2V 0dB 12dB 60Hz 12KHz 30Hz 250Hz FULL LPF HPF
Краткое содержание страницы № 8
REMOTE INPUT OUTPUT BASS SUB LOW LEVEL CONTROL POWER BOOST SONIC PASS L L PROTECT R R 0dB 12dB 15Hz 55Hz 40Hz 150Hz 6V 0.2V P1-2000.1 MONO AMPLIFIER APPLICATION Basic application These sub bass amplifiers can be used in any of the bi-amplification systems described in Crossover frequency control checklist: this manual, replacing the 2 channel amplifiers as per the illustrations. LOW PASS: 40Hz to 150Hz SUBSONIC:15 Hz
Краткое содержание страницы № 9
3/4 CH CONTROLS 1/2 CH CONTROLS CH5 CH4 CH2 MODE LEVEL HPF LEVEL HPF REMOTE L FULL HPF 4CH 5CH FULL HPF 5V 0.2V 10Hz 150Hz 5V 0.2V 10Hz 150Hz X-OVER X-OVER R 15Hz 55Hz 5V 0.2V 0dB 12dB 30Hz 150Hz POWER CH5 CH3 CH1 LEVEL SUBSONIC BASS EQ LPF PROTECT 5 CH CONTROLS P1-5000.5 5-CHANNEL AMPLIFIER APPLICATION Basic application Here we show how to use the channel amplifier as straightforward discrete
Краткое содержание страницы № 10
8
Краткое содержание страницы № 11
SETTING UP SYSTEMS AFTER INSTALLATION FOR BEST PERFORMANCE P1-600.2 / P1-1000.2 / P1-600.4 / P1-1000.4 / P1-5000.5 General: At this point you are ready to get more specific on the settings for your amplifier. High Pass: -When in HPF operation, this setting acts as a low frequency cut off for your system reproduction. The point that you set it at cuts off any frequencies from reproduction beyond this point. The 12 o’clock position is a great starting point. EXAMPLE: If you adjust the HPF to 100H
Краткое содержание страницы № 12
TROUBLESHOOTING A SYSTEM The key to finding the problem in a misbehaving sound system is to isolate parts of that system in a logical fashion to track down the fault. Description of the PROTECT system built into all Crunch amplifiers The diagnostic system will shut down the amplifier, until reset by turning the head unit off, and back on. This state of affairs will be indicated by the front panel PROTECT LED lighting up under the following conditions: 1 - A sort circuit on the loudspeaker lead
Краткое содержание страницы № 13
Maxxsonics Limited Warranty As the manufacturer of Maxxsonics, MB Quart, Autotek, Crunch and Hifonics car audio products, Maxxsonics USA Inc. Warrants to the original consumer purchaser the amplifier to be free from defects in material and workmanship for one (1) Year from date of purchase. All other parts and accessories of the system are warrantied to be free from defects in material and workmanship for one (1) year from date of purchase. Maxxsonics will repair or replace at it’s option and f
