Краткое содержание страницы № 1
KSD-800M
Series
Industrial Managed 8-Port Fast Ethernet Switches
with Fiber Connectivity
Installation Guide
DOC.050710
-1-
Краткое содержание страницы № 2
(C) 2002 KTI Networks Inc. All rights reserved. No part of this documentation may be reproduced in any form or by any means or used to make any directive work (such as translation or transformation) without permission from KTI Networks Inc. KTI Networks Inc. reserves the right to revise this documentation and to make changes in content from time to time without obligation on the part of KTI Networks Inc. to provide notification of such revision or change. For more information, contact: United St
Краткое содержание страницы № 3
The information contained in this document is subject to change without prior notice. Copyright (C). All Rights Reserved. TRADEMARKS Ethernet is a registered trademark of Xerox Corp. WARNING: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates,
Краткое содержание страницы № 4
Table of Contents 1. Introduction .................................................................................................. 6 1.1 Features ...................................................................................................................7 1.2 Product Panels .........................................................................................................8 1.3 Front Panel .........................................................................................
Краткое содержание страницы № 5
3.2.2.3 Unmatched VID Filtering (per port setting) ........................................................ 30 3.2.3 VLAN Group Mapping ........................................................................................... 31 3.2.4 Packet Forwarding under VLAN ........................................................................... 31 3.2.5 Egress Tagging Rules .......................................................................................... 31 3.2.5.1 Egress Tag Rule (per port
Краткое содержание страницы № 6
1. Introduction The KSD-800M series are managed 8-port full wire speed Fast Ethernet switches for industrial appli- cations. Depending on the fiber connectivity, the series is provided in three types of configuration as follows: Model series 10/100TX TP Ports 100FX fiber ports 800M 8 ports - 800M-1xxx 8 ports 1 port 800M-2xxx 8 ports 2 ports The switches provide the following advantages: Plug and Play The switches provide eight 10/100TX copper ports for connections to Ethernet devices or 100Mbp
Краткое содержание страницы № 7
Designed for Industrial Applications For industrial environment, the switches are designed with the following enhanced features: n High and wide operating temperature n Wide operating voltage range for DC power input n Power input interface: Screw terminal block and DC jack for adapter n Relay output for device power failure alarm n DIN rail mounting support for industrial enclosure n Panel mounting support for industrial enclosure 1.1 Features Basic functions • Fast Ethernet switch with 8 10/1
Краткое содержание страницы № 8
1.2 Product Panels The following figure illustrates three major panels of model 800-2 series as example: -8-
Краткое содержание страницы № 9
1.3 Front Panel The figure below shows the individual front panel of three model series. The main difference is the number of the equipped fiber ports. 1.4 Network Ports Model 800M provides eight 10/100TX copper ports only. No fiber connectivity is equipped. -9-
Краткое содержание страницы № 10
Model 800M-1 series provide eight 10/100TX copper ports and one 100FX fiber connector. Port 8 supports dual network cable types. Model 800M-2 series provide eight 10/100TX copper ports and two 100FX fiber connectors. Port 7 and Port 8 support dual network cable types. 1.5 LED Indicators LED Function PWR Power status LNK Network port link status (per port) 100M Network port speed status (per port) FX7 Fiber port link status (if FX7 is provided on Port 7) FX8 Fiber port link status (if FX8 is pro
Краткое содержание страницы № 11
1.6 Top Panel All three model series provide same top panel as figure shown below: The main functions are: DC Power Jack This connector is used when a AC-DC power adapter is used as a power source to the switch. Terminal Block This connector provides the following interfaces: DC1 Positive(+) and Negative(-) - VDC power input from power system DC2 Positive(+) and Negative(-) - VDC power cascaded to next device PF Positive(+) and Negative(-) - Power failure relay output Reset Hardware reset push
Краткое содержание страницы № 12
10/100TX Twisted Pair Ports Compliance IEEE 802.3 10BASE-T, IEEE 802.3u 100BASE-TX Connectors Shielded RJ-45 jacks Pin assignments Auto MDI/MDI-X detection Configuration Auto-negotiation Transmission rate 10Mbps, 100Mbps Duplex support Full/Half duplex Flow control IEEE 802.3x pause frame base for full duplex operation Back pressure for half duplex operation Network cable Cat.5 UTP 100FX Fiber Ports Compliance IEEE 802.3u 100BASE-FX Configuration Forced 100Mbps, Full duplex Transmission rate 100
Краткое содержание страницы № 13
Software Management Functions Interfaces Web, telnet, SNMP MIB-II & private MIB, Traps Management objects Port configuration control and status Username and password settings IP, SNMP related settings VLAN function settings QoS function setting Port Configuration Control Function Configuration P1 ~ P6 Port control function Port TX/RX - enable, disable Port mode - Auto (auto-negotiation), Forced Port speed - 100Mbps, 10Mbps Port duplex - full, half Port Status Port mode, link, speed, duplex VLAN
Краткое содержание страницы № 14
DC Power Input Interfaces Euro type terminal block contacts (DC1 DC2 : 2 sets for power wire cascading) DC Jack ( -D 6.3mm / + D 2.0mm) Operating Input Voltages +7V ~ +30V(+5%) Power consumption Model 800M 4.7W/7.5VDC input, 5.0W/30VDC input Model 800M-1 6.0W/7.5VDC input, 6.3W/30VDC input Model 800M-2 8.0W/7.5VDC input, 8.3W/30VDC input Mechanical Dimension (base) 140 x 106 x 40 mm Housing Enclosed metal with no fan Mounting Support DIN-rail mounting, Panel mounting Weight Model 800M: 465g, Mod
Краткое содержание страницы № 15
Optical Specifications A variety of fiber options and the optical specifications is provided as follows: Model FX Port & Cable Wavelength Tx Power Rx sensitivity Rx max. power 800M-1T FX8 : ST MMF 1310nm -19 ~ -14 dBm -34 dBm max. -14 dBm min. 800M-1C FX8 : SC MMF 1310nm -19 ~ -14 dBm -34 dBm max. -14 dBm min. 800M-1CL1 FX8 : SC MMF 1310nm -19 ~ -12 dBm -31 dBm max. -8 dBm min. 800M-1CL2 FX8 : SC MMF 1310nm -19 ~ -14 dBm -34 dBm max. -3 dBm min. 800M-1SA2 FX8 : SC SMF 1310nm -15 ~ -8 dBm -34 dBm
Краткое содержание страницы № 16
2. Installation 2.1 Unpacking The product package contains: • The switch unit • One DIN-rail mounting kit • One product CD-ROM 2.2 Safety Cautions To reduce the risk of bodily injury, electrical shock, fire, and damage to the equipment, observe the following precautions. • Do not service any product except as explained in your system documentation. • Opening or removing covers may expose you to electrical shock. • Only a trained service technician should service components inside these compar
Краткое содержание страницы № 17
2.3 DIN-Rail Mounting In the product package, a DIN-rail bracket is provided for mounting the switch in a industrial DIN-rail enclosure. The steps to mount the switch onto a DIN rail are: 1. Install the mounting bracket onto the switch unit as shown below: 2. Attach bracket to the lower edge of the DIN rail and push the unit upward a little bit until the bracket can clamp on the upper edge of the DIN rail. 3. Clamp the unit to the DIN rail and make sure it is mounted securely.
Краткое содержание страницы № 18
2.4 Panel Mounting The switches are provided with an optional panel mounting bracket. The bracket support mounting the switch on a plane surface securely. The mounting steps are: 1. Install the mounting bracket on the switch unit. 2. Screw the bracket on the switch unit. -18-
Краткое содержание страницы № 19
3. Screw the switch unit on a panel. Three screw locations are shown below: -19-
Краткое содержание страницы № 20
2.5 Applying Power The power specifications of the switch are: Operating Voltage +7 ~ +30VDC Power Consumption Max. 8.3W @30VDC The switch provides two types of power interfaces, terminal block and DC power jack for receiving DC power input from external power supply. Using Terminal Blocks Either DC1 interface or DC2 interface can be used to receive DC power from an external power system. Or, DC2 also can be used to deliver the power received on DC1 to next switch in cascading way. DC1 + Vdc Po
