Краткое содержание страницы № 1
USB HUB4 Series
AAP and MAAP USB Hubs
68-1735-01 Rev. A
08 09
Краткое содержание страницы № 2
Precautions Safety Instructions • English Warning Power sources • This equipment should be operated only from the power source indicated on the product. This This symbol is intended to alert the user of important operating and maintenance equipment is intended to be used with a main power system with a grounded (neutral) conductor. The (servicing) instructions in the literature provided with the equipment. third (grounding) pin is a safety feature, do not attempt to bypass or disable it. Th
Краткое содержание страницы № 3
FCC Class A Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. The Class A limits are designed to provide reasonable protection against harmful interference when the equipmen
Краткое содержание страницы № 4
USB HUB4 Series
Краткое содержание страницы № 5
Table of Contents Chapter One • Introduction ......................................................................................................1-1 About this Manual .....................................................................................................................1-2 About the USB HUB4 .................................................................................................................1-2 Features ..............................................................
Краткое содержание страницы № 6
Table of Contents, cont’d ii USB HUB4 Series • Table of Contents PRELIMINARY
Краткое содержание страницы № 7
USB HUB4 Series Chapter One 1 Introduction About this Manual About the USB HUB4 Application Diagram PRELIMINARY
Краткое содержание страницы № 8
Introduction About this Manual This manual contains information about the installation and operation of the Extron USB HUB4 AAP and the USB HUB4 MAAP. The terms “hub” and “HUB4” are used to refer to both models interchangeably when instructions apply to both. About the USB HUB4 The USB HUB4 AAP and USB HUB4 MAAP are compact, four-port USB hubs designed to mount within a double-sized Extron AAP or MAAP frame. They enable multiple USB devices to be connected to a single USB port on a host
Краткое содержание страницы № 9
Application Diagram The following diagram shows an example of a USB HUB4 AAP mounted to an MLM wallplate and installed in a podium. DISPLAY AUTO ON OFF 1 IMAGE MUTE 2 VOLUME 3 ACTIVITY CONFIG 4 USB HUB4 AAP MediaLink Extron MLM 104 LAAP with Extron USB HUB4 AAP MLC 104 IP Plus Four-Port USB 2.0 Hub One USB Cable from PC to USB HUB4 AAP Mouse Keyboard PC Application diagram for a USB HUB4 AAP USB HUB4 Series • Introduction 1-3 CENTERING RGB 202 Rxi VTG WITH ADSP TM PEAK INPU 1 T BOOST CON
Краткое содержание страницы № 10
Introduction, cont’d 1-4 USB HUB4 Series • Introduction PRELIMINARY
Краткое содержание страницы № 11
USB HUB4 Series Chapter Two 2 Installation Installation Overview Rear Panel Connections Front Panel Features Mounting the USB HUB4 PRELIMINARY
Краткое содержание страницы № 12
Installation Installation Overview If using an electrical box or a mounting bracket, install it in the wall or 1 furniture. See “Wall or furniture mounting”, later in this chapter. Mount the USB HUB4 into an appropriate sized AAP or MAAP 2 mounting frame, rack space frame, or other Extron architectural product. See “Mounting the hub to a mounting frame”, later in this chapter, for the procedure. Connect the USB HUB4 to the host computer in either of the following ways: 3 • Using the
Краткое содержание страницы № 13
The rear panels of the USB HUB4 AAP and MAAP models contain two types of USB In connectors, either of which can be used for the USB cable that connects your computer to the HUB4. Power connector — If using an Extron external 12 VDC power supply to a power the HUB4, connect it to the first two pins (labeled In) of this 4-pole, 3.5 mm direct insertion captive screw connector. (See “Connecting to the captive screw USB connector”, below) If desired, connect another Extron wall mounted devic
Краткое содержание страницы № 14
Installation, cont’d Red White Green Shield Type A connector Black USB Type A-to-B (or mini B) cable with the Type B connector removed 3. Twist the exposed shield strands together. 4. Strip 1/8 inch (4.5 mm) of the insulation from the end of each colored wire of the cable. 5. Connect the colored wires and the twisted shield to the HUB4 as described below. Note that each pin of the connector is labeled above with the color of the wire that should be connected to it (R, W, G, and B), b
Краткое содержание страницы № 15
USB HUB4 AAP Mounting Frame POWER Type Mini B 12V 500mA USB Connector IN IN OU OUT T Type A USB IN USB WIRE COLO WIRE COLOR R USB 1 RR WW GG BB USB Ports +V D- D+ S USB Cable (6’) Rear Red / +V Captive Screw White / D- USB Connector Green / D+ Black / Braided Shield / S Strip 1” to 2” from the outer jacket of the USB cable to expose the wires. N: Do not splice or extend the USB cable connecting the host computer to the HUB4 beyond 15 feet (4.5 m). Extending it further than this c
Краткое содержание страницы № 16
Power Audio 9-18 VDC L R Installation, cont’d To wire the Extron external power supply, 1. Connect the power supply to the In pins (first and second) of the Power direct insertion connector as illustrated below. Power Supply Output Cord A SECTION A–A POWER 12V 500mA IN IN OU OUT T USB IN WIRE COLOR WIRE COLOR RW RW GB GB +V +V D- D- D+ D+ S S Wiring the power connector 2. (Optional) If you want the power supply to power an additional wall- mounted Extron device via the USB HUB4
Краткое содержание страницы № 17
Front Panel Features 1 ACTIVITY 3 2 HUB4 USB AAP USB HUB4 AAP 1 USB HUB4 AAP front panel 1 ACTIVITY 3 2 ACTIVITY USB HUB4 MAAP HUB4 USB MAAP 1 USB HUB4 MAAP front panel USB hub connectors — Connect up to four USB peripheral devices (for a example, a keyboard, mouse, or Web cam) to these Type A female USB connectors. Each USB port provides 100 mA of power when the HUB4 is powered via the host computer; 500 mA when it is powered by an Extron PS 1210 C 12 VDC external power supply. Activi
Краткое содержание страницы № 18
Installation, cont’d Mounting the USB HUB4 The USB HUB4 can be mounted to a wall, on a rack, in furniture, or in an Extron architectural product, such as a cable cubby or HSA. Wall or furniture ounting m The HUB4 can be attached to a wall, podium, or other flat surface with either a stud-mounted wall box or with a wall mounting bracket (such as the Extron MR or MR D series). Both types of installations require a double-spaced AAP or MAAP mounting frame (such as the AAP 102 or the CPM101).
Краткое содержание страницы № 19
6. Insert the wall box or mounting bracket into the opening, and attach it to the wall, stud, or furniture, leaving the front edge flush with the outer wall or furniture surface. Wall Stud Wall Stud Installation Cable Installation Cable Cable Clamp Cable Clamp Screws or Nails Screws or Nails Attaching a wall box to a wall stud • To attach a wall box to wood, use four #8 or #10 screws or 10-penny nails. A minimum of 1/2 inch (1.3 cm) of screw threads must penetrate the wood. • To attach a
Краткое содержание страницы № 20
Installation, cont’d AAP 102 Mounting Frame Extron USB HUB4 AAP Mounting a USB HUB4 AAP to a two-gang mounting frame USB HUB4 MAAP: 1. Place the HUB4 MAAP in the one-gang opening in the mounting frame. 2. Insert the included hex screws through the HUB4 front panel mounting holes and the holes in the MAAP mounting frame. 3. Attach the provided hex nuts to the screws on the back of the frame. Mounting the hub to a wall box To mount the HUB4 to an electrical box in a wall or furniture, 1. M
