Краткое содержание страницы № 1
ISS 408 & ISS 108
Integration Seamless Switchers
68-575-01 Rev. C
05 05
Краткое содержание страницы № 2
Precautions Safety Instructions • English Warning Power sources This equipment should be operated only from the power source indicated on the This symbol is intended to alert the user of important operating and maintenance product. This equipment is intended to be used with a main power system with a grounded (servicing) instructions in the literature provided with the equipment. (neutral) conductor. The third (grounding) pin is a safety feature, do not attempt to bypass or This symbol is inte
Краткое содержание страницы № 3
AUDIO AUDIO Quick Start — Integration Seamless Switcher Tip Sleeve Step 5 Installation Tip Cable the switcher for Sleeve stereo audio input. Each Step 1 Unbalanced Input (high impedance) input has a 3.5 mm, 5-pole Turn off power to the ISS 108 or ISS 408 and the Tip captive screw connector for input and output devices, and remove the power Ring Sleeve (s) balanced or unbalanced cords from them. Tip Ring stereo or mono audio Balanced Input input. Connectors are (high impedance) Step 2 included
Краткое содержание страницы № 4
Quick Start — Integration Seamless Switcher, cont’d 2. Press an input button (to select the input to Step 9 configure). If desired, connect a control system or computer to the Remote RS-232 port. 3. Rotate the Adjust knob to select the input video type. 51 Pin RS-232 Function 4. Rotate the Adjust knob to select the input 1 — Not used audio gain or attenuation level. 2 TX Transmit data 3 RX Receive data 9 6 5. Select other inputs to configure as necessary 4 — Not used Female 5 Gnd Signal ground
Краткое содержание страницы № 5
Table of Contents Chapter 1 Introduction ....................................................................................................... 1-1 About this Manual ............................................................................................................. 1-2 About the Switcher............................................................................................................ 1-2 Features .............................................................................
Краткое содержание страницы № 6
Table of Contents, cont’d Preview Switch Mode submenu ........................................................................ 3-14 PAL Fil Mode submenu...................................................................................... 3-15 Reset submenu .................................................................................................. 3-15 User Presets menu ...................................................................................................... 3-16 Save Preview
Краткое содержание страницы № 7
Using the Command/Response Table ........................................................................ 4-8 Command/response table for SIS commands .................................................................. 4-9 Command/response table for IP SIS commands ............................................................ 4-15 Command/response table for special function SIS commands ..................................... 4-16 Command/response table for advanced instruction Set commands .........
Краткое содержание страницы № 8
Table of Contents, cont’d Chapter 7 Maintenance and Modifications .......................................................... 7-1 Opening and Closing the Switcher ............................................................................ 7-2 Firmware Upgrade Installation.................................................................................... 7-3 DVI Output Card Installation ........................................................................................ 7-4 Appendix A Et
Краткое содержание страницы № 9
Integration Seamless Switcher Chapter One 1 Introduction About this Manual About the Switcher Features
Краткое содержание страницы № 10
Intr Intr oduction, cont’d oduction About this Manual This manual contains installation, configuration, and operating information for the Extron ISS 108 and ISS 408 Integration Seamless Switchers. The ISS 108 and ISS 408 are similar in function and operation; the differences exist in scaling capabilities. In this manual, the terms “switcher” and “ISS” are used interchangeably to refer to either model, except where differences exist, in which case the specific model is noted. Chapter 1 identif
Краткое содержание страницы № 11
Preview Monitor Program Monitor Projector Extron ISS 408 RS-232 LAN/WAN Network/ Internet DVD Player Codec Extron RGB 109xi VCR Laptop Podium PC Figure 1-1 — Typical ISS 408 Integration Seamless Switcher application The ISS receives and outputs the stereo audio on 5-pole captive screw connectors. The audio can be switched with cross fading (that is, the previous audio channel fades out and then the new audio channel fades in). For upscaling, the ISS 408 converts the horizontal and vertical sync
Краткое содержание страницы № 12
Introduction, cont’d Features Inputs — Video inputs — The ISS switches among eight fully-configurable RGB, HDTV component video (ISS 408), component video, S-video, and composite video inputs on five BNC connectors per input. Audio inputs — The ISS switches among eight balanced or unbalanced stereo or mono audio inputs on 5-pole captive screw connectors. Outputs — Standard video outputs — The ISS outputs individually scaled video signals as RGBHV or RGBS. Two sets of BNC connectors and two 15-p
Краткое содержание страницы № 13
Audio cross-fading — A transition technique that is applied during the switches that lowers the audio level of the switched out source while simultaneously raising the audio level of the activated source. Ethernet port — Supports connection to an Ethernet LAN so that the switcher can be accessed and operated from a computer running a standard Internet browser anywhere in the world. Quad-standard video decoder — The switcher uses a digital, four-line adaptive comb filter that can decode NTSC 3.58
Краткое содержание страницы № 14
Introduction, cont’d 1-6 Integration Seamless Switcher Introduction
Краткое содержание страницы № 15
Integration Seamless Switcher Chapter Two 2 Installation Mounting the Switcher Cabling and Rear Panel Views Configuration
Краткое содержание страницы № 16
Installation, cont’d Installation Mounting the Switcher Four uninstalled rubber feet are included with the switcher. If you are going to rack mount the switcher, mount it before you cable it (see Rack mounting, below), and do not install the rubber feet. If you are not rack mounting the switcher, see Tabletop placement below. Tabletop placement For tabletop placement, install the self-adhesive rubber feet/pads (provided) onto the four corners of the bottom of the switcher. Rack mounting To rac
Краткое содержание страницы № 17
LINK ACT Cabling and Rear Panel Views All connectors are on the rear panel (figure 2-2). 2 4 5 OUTPUTS INPUTS 12 3 4 5 6 7 8 PROGRAM PREVIEW PROGRAM R/R-Y R/R-Y R/R-Y R/R-Y R/R-Y R/R-Y R/R-Y R/R-Y R R PREVIEW DVI OUT G/Y G/Y G/Y G/Y G/Y G/Y G/Y G/Y G G VID VID VID VID VID VID VID VID B/C B/C B/C B/C B/C B/C B/C B/C B B B-Y B-Y B-Y B-Y B-Y B-Y B-Y B-Y RS-232 8 100- 240 50/60 Hz 1.2A MAX. H/HV H/HV H/HV H/HV H/HV H/HV H/HV H/HV H/HV H/HV V V V V V V V V V V ETHERNET 1 23 4 5 6 7 8 1 3 6 7 9 10 F
Краткое содержание страницы № 18
Installation, cont’d Input audio connectors — Connect balanced or unbalanced stereo or mono 3 audio to these 3.5 mm, 5-pole captive screw connectors. Connectors are included with the seamless switcher, but you must supply the audio cable. Figure 2-4 shows how to wire a connector for the appropriate input type and impedance level. High impedance is generally over 800 ohms. 600 ohms Tip Tip Tip Sleeve Ring Ring Sleeve (s) Sleeve (s) Tip Tip Tip Ring Ring Sleeve 600 ohms Unbalanced Input Balanced
Краткое содержание страницы № 19
Standard output connections The two Program Video outputs, consisting of five BNC connectors and a 15-pin HD connector, output the identical video signal and the same sync format. The two Preview Video outputs are also identical to each other. 4 The Program connectors ( ) output the video image for the program monitor or 5 projector. The Preview connectors ( ) output the video image for the local monitor. Preview and Program video output BNC connectors — Connect RGB video 4 displays to these f
Краткое содержание страницы № 20
Installation, cont’d Optional output connection 8 DVI output connector (optional) — If the optional DVI output 9 card is installed, connect a DVI/DFP-compatible video display to this DVI connector. This connector outputs the program image 17 1 only. For a DFP-compatible display, connect the display through a DVI-to-DFP adapter, part #26-497-01 (DVI [male] to DFP [female] adapter) or 26-498-01 (DVI [female] to DFP [male] adapter). 24 8 The DVI output’s horizontal resolution is limited to either
