Краткое содержание страницы № 1
DS00331ACN/WS100R 1/8/04 9:47 AM Page 2
INSTALLATION & OPERATION GUIDE
WS100R
WS100R
WALL-MOUNT INFRARED SENSOR
®
B LENDING H IGH F IDELITY AND A RCHITECTURE
Краткое содержание страницы № 2
DS00331ACN/WS100R 1/8/04 9:47 AM Page 3 W ALL -M OUNT I NFRARED S ENS OR WS100R Wall-Mount Infrared Sensor TABLE OF CONTENTS Introduction ® The WS100R is a wall-mount, Decora style IR sensor Introduction 1 designed for use with the Niles infrared extender systems. Installed in a remote room location, the WS100R receives the Features and IR commands transmitted from your existing hand-held Benefits 2 remotes in that room. The commands are carried via a Installation category 5 cable to your
Краткое содержание страницы № 3
DS00331ACN/WS100R 1/8/04 9:47 AM Page 4 W ALL -M OUNT I NFRARED S ENS OR Features and Benefits The WS100R offers a number of improvements over other wall-mount IR sensors. • Plasma-proof performance— allows placement of the WS100R near plasma displays. • CFL interference resistant— expands installation flexi- bility to areas with fluorescent lighting. •Works under most lighting conditions, including indi- rect sunlight— eliminates environmental restrictions. • Universal system— compatible wit
Краткое содержание страницы № 4
DS00331ACN/WS100R 1/8/04 9:47 AM Page 5 W ALL -M OUNT I NFRARED S ENS OR Installation Considerations The WS100R is a Decora-style module and is designed to use standard Decora-style cover plates and mounting hardware. Decora cover plates (up to 6-gang) with color-matched plate screws are available from your Niles dealer. Type of Cable The WS100R connects to the Niles infrared main systems unit or IRH610 sensor expansion hub with an individual home run of category 5 cable. When running wires i
Краткое содержание страницы № 5
DS00331ACN/WS100R 1/8/04 9:47 AM Page 6 W ALL -M OUNT I NFRARED S ENS OR as strong as remotes that use the larger AA size batteries and TOOLS have two emitters. Tests with various manufacturers’ remote REQUIRED controls have shown that the operating range can vary from a minimum of 18' to a maximum of about 30'. • 1/8" Standard Slotted Screwdriver Infrared signals travel essentially line-of-sight. They will not pass through or around solid objects. Do not rely on an IR • 1/4" Standard signal
Краткое содержание страницы № 6
DS00331ACN/WS100R 1/8/04 9:47 AM Page 7 W ALL -M OUNT I NFRARED S ENS OR Niles IR Flasher Stereo Receiver 12V DC power supply (supplied with the MSU250 Main System Unit) plugged into an unswitched AC outlet powers the system 3-30V AC/DC STATUS IN 12V DC Power Supply (Not Supplied) plugged into the Switched Outlet Niles Stock#FG000665 MSU250 Power, IR Data, and Power Status Signal via category 5 cable Figure 1 Wiring Diagram (Typical installation with an MSU250 Main System Unit) WS100 IR
Краткое содержание страницы № 7
DS00331ACN/WS100R 1/8/04 9:47 AM Page 8 W ALL -M OUNT I NFRARED S ENS OR Figure 2 WS100R Parts Guide a e g b c f d e (a) Electrical Box (b) Category 5 cable g (c) WS100 IR Receiver (supplied) (d) Snap-on Color Insert (supplied) (e) Device Screws (2 supplied) (f) Decora Faceplate (supplied) (g) Faceplate Screws (2 supplied) 6
Краткое содержание страницы № 8
DS00331ACN/WS100R 1/8/04 9:47 AM Page 9 W ALL -M OUNT I NFRARED S ENS OR Avoiding Interference The WS100R is designed to work in most applications including plasma displays and in areas where CFL lighting and indirect sunight are present. You should avoid locating the WS100R near potential sources of electrical or optical noise, such as light dimmers or low-voltage lights. Avoiding Electrical Interference Avoid locating the WS100R near any potential sources of electrical or optical noise, suc
Краткое содержание страницы № 9
DS00331ACN/WS100R 1/8/04 9:47 AM Page 10 W ALL -M OUNT I NFRARED S ENS OR 2. Hold the WS100R as shown in (Figure 3). Locate the two plastic mounting tabs at the top rear of the Decora-style insert. Using two fingers, simultaneously press both tabs down (towards the center of the insert) and forward (away from you) until the insert pops free from its mounting slots. 3. Locate the new Decora-style insert. Hold the WS100R so that it is facing you. Insert the two bottom tabs into the bottom slot
Краткое содержание страницы № 10
DS00331ACN/WS100R 1/8/04 9:47 AM Page 11 W ALL -M OUNT I NFRARED S ENS OR Installation If you are installing the WS100R into an existing wall, “TECH TIP” take time to consider any possible obstructions which may be hidden inside the wall, such as wood or metal studs, Avoid installing the electrical, telephone or other types of wiring, plumbing, WS100R next to AC or heating conduit, etc. a light dimmer. 1. Locate the connector plug. 2. Strip 1/4" of insulation from the end of each wire. 3
Краткое содержание страницы № 11
DS00331ACN/WS100R 1/8/04 9:47 AM Page 12 W ALL -M OUNT I NFRARED S ENS OR Figure 5 Installing the Connector NOTE: Certain “old work” or “retro-fit” boxes, such as the Carlon B225R, have a plastic “lip” which interferes with the Decora plate screws. This lip prevents you from being able to tighten these screws completely. To make the clearance nec- essary for these screws, you must remove the parts of the lip causing the interference. There are two ways to accomplish this: 1. Drill through t
Краткое содержание страницы № 12
DS00331ACN/WS100R 1/8/04 9:47 AM Page 13 W ALL -M OUNT I NFRARED S ENS OR Intellipad Wiring See your MSU manual if you are connecting the WS100R with an IntelliPad system. Operation Operation of the WS100R is simple. Stand within the operational range of your WS100R. Aim your hand-held remote at the WS100R and press the button for the desired command. Your IR command is instantly repeated to your A/V equipment. Green “Power Status” LED When the WS100R is correctly connected (as shown in Fi
Краткое содержание страницы № 13
DS00331ACN/WS100R 1/8/04 9:47 AM Page 14 W ALL -M OUNT I NFRARED S ENS OR Troubleshooting This manual contains instructions for the WS100R only. For specific information on the adjustment and operation of your Niles infrared extender system, please refer to the instruction manual included with your Niles IR main system unit (MSU140, ® MSU250, MSU480 MSU440Z, IntelliControl ). The bi-color blue/green LED on the front of the WS100R is a useful troubleshooting aid. The led should light solid g
Краткое содержание страницы № 14
DS00331ACN/WS100R 1/8/04 9:47 AM Page 15 W ALL -M OUNT I NFRARED S ENS OR Eliminating optical feedback In some installations, two conditions combine to create an optical feedback loop. Symptoms can include: poor range, intermittent operation or no operation. The conditions which sometimes combine to create a feed- back loop are: 1. Both a sensor and a flasher are located within the same room. 2. There is some low-level noise or interference on your system. You can eliminate optical feedback
Краткое содержание страницы № 15
DS00331ACN/WS100R 1/8/04 9:47 AM Page 16 W ALL -M OUNT I NFRARED S ENS OR Identifying the type of interference The “flash-back” LED on the front of the WS100R is a useful trouble-shooting aid. The LED should light blue only when a remote command is being received. However, if the LED on the WS100R “flickers”, and the WS100R functions normally, there is no cause for concern. If the WS100R does not work, and the LED does not light at all: Test the remote control(s) by operating the A/V equipm
Краткое содержание страницы № 16
DS00331ACN/WS100R 1/8/04 9:47 AM Page 17 W ALL -M OUNT I NFRARED S ENS OR 1. Move the sensor or the sensor cable away from the EMI source or move the source of the EMI away from the sensor or the cable. 2. Connect the Sensor’s GND terminal to true earth ground (if this isn’t feasible use the main system unit’s GND terminal). There are many methods for reducing interference. Which solution is best for you depends on your situation. If you require further assistance contact Niles Technica
Краткое содержание страницы № 17
DS00331ACN/WS100R 1/8/04 9:47 AM Page 18 W ALL -M OUNT I NFRARED S ENS OR Specifications Contents IR System WS100R Sensor x1 Compatible with virtually all brands Decora Insert x1 of remotes using carrier frequencies between 26 and 105 kHz. Decora faceplate x 1 IR Receiving Range Removable connector x 1 Varies depending on remote Device Mounting Screws x 2 strength; 18 to 30' typical. Faceplate Spaces x 2 IR Receiving Angle 30°off-axis (horizontal and vertical) at 18'. Mounting In-wall, fits i
Краткое содержание страницы № 18
DS00331ACN/WS100R 1/8/04 9:47 AM Page 19 W ALL -M OUNT I NFRARED S ENS OR Notes 17
Краткое содержание страницы № 19
DS00331ACN/WS100R 1/8/04 9:47 AM Page 20 W ALL -M OUNT I NFRARED S ENS OR Notes 18
Краткое содержание страницы № 20
DS00331ACN/WS100R 1/8/04 9:47 AM Page 1 ® Niles Audio Corporation www.nilesaudio.com 12331 S.W. 130 Street ©2004 Niles Audio Corporation. All rights reserved. Niles, the Niles logo, IntelliPad and Blending High Fidelity and Miami, Florida 33186 Architecture are registered trademarks of Niles Audio Corporation. MicroFlasher is a trademark of Niles Audio Corporation. Because we strive to improve our products. All other trademarks are the property of their respective Tel: (305) 238-4373
