Краткое содержание страницы № 1
M7000
Краткое содержание страницы № 2
TABLE OF CONTENTS INTRODUCTION 1 FEATURES 2 - 4 INSTALLATION BASICS 4 -8 INSTALLATION WIRING 9 -12 VARIOUS IMPEDANCE WIRING 13 -14 SPECIFICATION 15
Краткое содержание страницы № 3
Thank you for purchasing a Cadence Amadeus Amplifier. The Amadeus series is a breakthrough in sound quality and design. The amplifier features our own hybrid digital technology that was made famous with the venerable A7HC--only we took it one step further. Not only is the Amadeus a Digital Class D amplifier it is also capable of playing the full range audio spectrum. (All models except the M7000 which is a pure sub woofer amplifier.) With this new circuitry, we have been able, to package l
Краткое содержание страницы № 4
NICKEL PLATED TERMINALS All the terminals on the amplifier are solid brass and satin nickel plated for high conductivity and minimum impedance loss. The power and ground terminals are extra large and capable of accepting 4 gauge wire. The speaker terminals can accept 8 gauge wire. When wiring the amplifier, be sure to strip just enough wire that fits into the terminal so that bare wires do not touch each other, or the amplifier chassis and cause a short circuit. POWER AND PROTECTION CIRCUI
Краткое содержание страницы № 5
BASS DRIVE EQUALIZATION CIRCUITRY A narrow "Q" shelving equalization circuit is included in the amplifiers. The equalization system is preset at 45Hz. The boost control allows you to add up to 12dB of Bass Drive effect. Utilize the Bass Drive to tailor your bass response to your systems needs. Please keep in mind that by adding Bass Drive you are adding stress on your speakers. Make sure that your speakers can handle the extra power output! It would be foolish to add 12dB of gain to low
Краткое содержание страницы № 6
Thermal Protection: When the amplifier reaches an unsafe operating temperature of 80 degrees Celsius the amplifier will turn off. Once the amplifier cools down, simply reset the amplifier by its Remote connection,(turn the amplifier off and then of again once you have given the amplifier a chance to cool down) and the amp will once again begin to play. If you live in hot climate we suggest installing additional cooling fans in your trunk to exhaust the hot air which can build up in the tr
Краткое содержание страницы № 7
It is recommend that you layout your sound system design on paper first. This will help you during the installation so that you will have a wiring flow chart and not miss-wire any of your components. Mount the amplifier in the trunk or hatch area of your vehicle. Never install an amplifier in the engine compartment or on the firewall. Please be sure to leave breathing room around the amplifier heatsink so that it can dissipate the heat it produces efficiently. The amplifier can be install
Краткое содержание страницы № 8
Over the years we have received many an amp back to our service department with melted power/ground terminals. The cause of this is a bad ground connection. When there is a lack of good ground heat builds up at the weakest point which is the contact screw of the terminal. Over time the heat generated will begin to melt the terminal. It is a good practice to feel the power and ground wires with your hands, near their amplifier connection after having played the amp for a while. If the wires
Краткое содержание страницы № 9
ADJUSTING THE SYSTEM Once the system is operational, the first thing to do, is set all crossover points to approximate settings. In the case of the basic subwoofer system, set the Low Pass filter crossover at 100 Hz or so. Set the Bass Boost equalizer control to 0 dB. Now you should set the amplifiers LEVEL adjustment. The knob accessible on the front of the amplifier marked Input Level adjusts the input sensitivity from150mV to 9 Volts. To adjust the input sensitivity, turn the control usi
Краткое содержание страницы № 10
PROTECTION LINE OUT LOW INPUT SUB LOW PHASE BASS SPEAKER POWER LEVEL SONIC PASS SHIFT BOOST L 0 +18dB Min Max 15 40Hz 50 150Hz 0 180 BRIDGED MODE R MASTER SLAVE DATA LINK LINE OUT From OUTPUTS of Woofer to SUB amp HEAD UNIT LINE IN REMOTE POWER FUSES +12V REM GND Remote GROUND Control To REMOTE TURN-ON In-Line Fuse Holder from HEAD UNIT Distribution Block BAT TERY Capacitor 8
Краткое содержание страницы № 11
PROTECTION LINE OUT LOW INPUT SUB LOW PHASE BASS SPEAKER POWER LEVEL SONIC PASS SHIFT BOOST L 0 +18dB Min Max 15 40Hz 50 150Hz 0 180 BRIDGED MODE R MASTER SLAVE DATA LINK BRIDGED MODE From OUTPUTS of LINE OUT HEAD UNIT MASTER SLAVE SPEAKER to SUB amp LINE IN IMPEDANCE 2 OHMS! BRIDGED SWITCH: MASTER POSITION PROTECTION LINE OUT LOW INPUT SUB LOW PHASE BASS POWER SPEAKER LEVEL SONIC PASS SHIFT BOOST L 0 +18dB Min Max 15 40Hz 50 150Hz 0 180 INPUT SENSITIVITY BRIDGED MODE R 2-8V MASTER
Краткое содержание страницы № 12
HOW TO TROUBLE SHOOT A SYSTEM GENERAL A car stereo system consists of many different pieces of equipment connected together, and a logical process of elimination will find the problem area, by isolating sections, and checking them one at a time. Before following the instructions below, check and double check all wiring and connections. TOOLS NEEDED The following tools will help in finding problems: A general purpose multi meter, capable of checking voltage and resistance, is perhaps the mo
Краткое содержание страницы № 13
AMPLIFIER OVERHEATING AND SHUTTING DOWN The most common cause for this problem is when amplifiers are overloaded with speaker impedances lower than what they are rated for. Double-check the impedance of your speakers and their wiring. Also check that no speaker leads are shorted to the vehicle metal chassis. AMPLIFIER GOING INTO PROTECTION When an amplifier goes into protection mode, we have to first establish whether the problem lies with the amplifier, or whether it is something in the in
Краткое содержание страницы № 14
M7000 4 Ohm Competition rating 50 Watts 2 Ohm Power 500 Watts 1 Ohm Power 1000 Watts Variable Low Pass Filter 50Hz - 150Hz Variable Sub Sonic Filter 15Hz - 40Hz Phase Shift Control 0 - 180 Frequency Response 15Hz - 150KHz Signal/Noise Ratio >100dB Damping Factor >500@100Hz Minimum THD <0.03% Input Voltage 200mV - 9 Volt Dimensions(L x W x H) 12.5" x 7.25" x 2.6" 2 Ohm Power when two M7000 are strapped together is 2000 Watts. 12
Краткое содержание страницы № 15
4 X DUAL VC 8 OHM SPEAKER WITH SERIES VOICE COILS, ALL IN PARALLEL 2 OHM 4+4 4+4 4+4 4+4 TO OHM OHM OHM OHM AMPLIFIER PARALLEL: SINGLE VOICE COIL SPEAKERS 2 OHM TO 4 OHM 4 OHM AMPLIFIER SERIES: SINGLE VOICE COIL SPEAKERS 2 OHM 4 OHM TO AMPLIFIER 2 OHM 13
Краткое содержание страницы № 16
PARALLEL: SERIES: DUAL VOICE DUAL VOICE COIL COIL SPEAKERS SPEAKERS 8 OHM 4+4 2 OHM 4+4 TO TO OHM AMPLIFIER OHM AMPLIFIER 2X DUAL VC 2 OHM SPEAKERS WITH SERIES VOICE COILS, ALL IN PARALLEL 4 OHM 2+2 TO OHM AMPLIFIER 2 OHM 2+2 2+2 TO OHM OHM AMPLIFIER 2 OHM 1+1 TO OHM AMPLIFIER Please note that the minimum impedance load for single Cadence Amadeus Series amplifiers is 2 ohm stereo and 4 ohm mono bridged. Lower impedance loads will cause overheating and may damage the amplifiers. Do not mix
Краткое содержание страницы № 17
Краткое содержание страницы № 18
