Руководство по эксплуатации Soundstream Technologies Granite 110.2

Краткое содержание страницы № 1

SOUNDSTRENvl@
r E C H 0 L 0.G I ,E S
..-.__ ___ _
Granite II 0.2
POWER
AMPLIFIER
&’

Краткое содержание страницы № 2

Mixed Mono Capable so you can simultaneously drive a stereo and mono load (satellites and subwoofer). 2 Ohm Drive Ability - The Granite amplifiers are designed to drive loads down to 2 Ohms stereo and 4 Ohms bridged. Built-in Staggered Asymmetrical Crossover - Built in 2-way electronic crossover is designed to send either high or low pass information to the 110.2. Outputs are included to drive another amplifier with either high or low pass information. Bass - Adjustable bass equalization circuit

Краткое содержание страницы № 3

12 dB/octave Passive Crossover Chart Key: L = high quality (DCR Ohm) inductor/coil C = non-polarized 50 V (or greater) capacitor XXX LOW 8 HIGH PASS DIAGRAMS XXX ~1

Краткое содержание страницы № 4

WIRING You will need the following tools for the wiring of the amplifier: . Phillips or slotted screw driver . wire strippers l wire crimpers When baring the wires for connection to the amplifier, remove to of the insulation. For the speaker leads, use the supplied insulated female crimp connectors and slide the connector onto the terminal on the amplifier. One the power, ground, and remote connections, loosen the screws on the terminal block, slide the bared wire into the connector, and tigh

Краткое содержание страницы № 5

TROUBLESHOOTING No sound and are not lit no power or ground at amp no remote turn-on signal blown fuse near battery blown power supply fuse (accessible through access cover on bottom of amp) Repeatedly blown amp fuse or speaker or leads may be shorted frequent activation of thermal verify adequate cooling of the shut-off amplifier speaker load may be less than 2 Ohms LEDs CAUSE PROBLEM

Краткое содержание страницы № 6

F. Re-connect the fuse or circuit breaker. Power up the system and the red LED should be lit. There may be a 2 -3 second delay from the time that the source unit is turned onto the time that the LED on the amp lights. This is normal. Once the amplifier power LED is on and the source unit is playing, you should have sound coming from the speakers. Wiring Tips . Use grommets when running cables through any metal or sharp plastic to prevent accidental shorting or shearing. . Be certain that the cab

Краткое содержание страницы № 7

AMPLIFIER LOCATION AND MOUNTING The Soundstream Granite 110.2 amplifier employs highly efficient circuitry and a unique Chassisink TM design to maintain lower operating temperatures. mounting the amplifier, it should be securely fastened to the vehicle, away from moisture, stray or moving objects, and major electrical components (electrical motors, fuel pumps, etc.). To provide adequate ventilation, mount the amplifier so that there are at least two inches of freely-circulating air above and to

Краткое содержание страницы № 8

PASSIVE AND ELECTRONIC CROSSOVERS Your Granite amplifier is capable of driving a complete subwoofer and satellite system in the Mixed Mono configuration. However, for the lowest distortion and the maximum output and sound quality, we recommend you use electronic crossovers and multiple channels of amplification. The Granite 110.2 amplifier incorporates an electronic crossover with outputs. This amplifier, in conjunction with another amplifier, will competently drive an entire bi-amplified system

Краткое содержание страницы № 9

OWNER’S MANUAL & INSTALLATION GUIDE CONGRATULATIONS You now own the Soundstream Granite 110.2 Amplifier, the result of a unique design and engineering philosophy. To maximize the performance of your system, we recommend that you thoroughly acquaint yourself with its capabilities and features. Please retain this manual and your sales and installation receipts for future reference Soundstream amplifiers are the result of American craftsmanship and the highest quality control standards, and when pr