Краткое содержание страницы № 1
Краткое содержание страницы № 2
CONTENTS Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 What's In The Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Practice Safe Sound™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Краткое содержание страницы № 3
INTRODUCTION Thank you for your purchase of Orion's 8002 power amplifier. Each Orion amplifier is designed to be the leader in its class offering the most power, advanced features, and extreme ease of use. In high-end sound systems or high SPL systems, Orion amplifiers will give you years of trouble-free performance. ● 8002 - 200 Watt per channel two-channel high current amplifier with built-in fully variable high-pass, low-pass, or band-pass crossover with INTELLLi Q. Equipped with remote gain
Краткое содержание страницы № 4
WARRANTY Directed Electronics, Inc. promises to the original purchaser, to replace this product should it prove to be defective in workmanship or material under normal use, for a period of two years from the date of purchase by the dealer as indicated by the date code marking of the product PROVIDED the product was installed by an authorized Directed dealer. During this two year period, there will be no charge for this replacement PROVIDED the unit is returned to Directed, shipping pre-paid. If
Краткое содержание страницы № 5
SPECIFICATIONS Amplifier Section Power Output 4W Stereo (Watts)1 200 x 2 Power Output 2W Stereo (Watts)2 400 x 2 Power Output 4W Mono (Watts) 800 x 1 Remote Gain Yes Distortion at Rated Power < 0.1% THD+N Frequency Response 20Hz to 20kHz ±0.25dB Linear Bandwidth 10Hz to 50kHz ±3dB Signal-to-Noise Ratio at Rated Power > 100dB Damping Factor > 200 Input Sensitivity 200mV to 5V Input Impedance 40kW Fuse Type 80 Amp MAXI Dimensions 23.4" x 10.5" x 2.3" Weight 10 lbs. Crossover Section Low Pass Cross
Краткое содержание страницы № 6
END PANEL LAYOUT 1. Power LED - when lit indicates that the amplifier is on. 2. Stereo/Mono Switch - configures the amplifier for one or two inputs. 3. Gain Control - continuously adjusts from 200mV to 5V for full power output. 4. Copy/Gain/Master Switch - determines the output of the RCA outputs. 5. RCA Inputs - accepts RCA input from a source unit, preamplifier, or equalizer. 6. RCA Outputs - provides easy connection to additional amplifiers. 7. Low-Pass Crossover Switch - activates 2nd or 4t
Краткое содержание страницы № 7
Stereo / Mono Input Configuration The STEREO / MONO switch allows the Orion 8002 amplifier to use a single RCA or high- level input to feed signal to both the right and left channels of the amplifier. When the switch is to the right (MONO position), signal from the left input is routed to the right chan- nel. When the switch is to the left (STEREO position), right and left inputs are independent. This allows a source unit with an internal balance to change the stereo imaging. Input Gain The Orio
Краткое содержание страницы № 8
Internal Crossover Configurations The crossover section of the Orion 8002 amplifier is continuously variable and extremely flexible. There are different crossover configurations possible allowing high-pass, low-pass, and band-pass configurations. The high-pass crossover incorporates the INTELLi Q feature. This circuit is designed to optimize the performance of Orion subwoofers in all types of enclosures. When using Orion loudspeakers, minor deviations from the recommended frequency ranges can pr
Краткое содержание страницы № 9
Enclosure Type Boost Levels 0dB +3dB +6dB +10dB Infinite Baffle Tune above High X-Max Not Not Fs of woofer Drivers--Tune Recommended Recommended above Fs of woofer Sealed Tune above Tune above High X-Max Not Fs of woofer Fs of woofer Drivers--Tune Recommended above Fs of woofer Vented Tune to port Tune to port Tune to port High X-Max frequency frequency frequency Drivers--Tune to port frequency Sealed Band-pass Tune above Tune above High X-Max Not Fs of woofer Fs of woofer Drivers--Tune
Краткое содержание страницы № 10
Sealed Example High-Pass Set at 20Hz This sealed example is the same 12-inch woofer in the recommended sealed enclosure. Up to 6 dB of boost is capable if 20 Hz was used. With +6dB of boost, the woofer has more out- put down to 15 Hz. Sealed Example High-Pass Set at 30Hz In this example, the frequency has been increased to 30 Hz. Up to 6 dB of boost is capable at this frequency. With +6dB of boost, the woofer has more output down to 23 Hz. The overall usable output is increased. Vented Example H
Краткое содержание страницы № 11
AMPLIFIER WIRING Power Connections ● 8002 Fuse Size: 1 x 80 AMP MAXI ● Power connections accept up to four-gauge wire. ● Four-gauge power and ground wire recommended for optimal performance. ● Connect 12V+ to the battery through fuse holder. This connection provides +12V main power to the amplifier. ● Power wire must be fused no more than 18" from battery. ● Ground amplifier to a good chassis ground as close as possible to the amplifier. ● Connect REM terminal to remote turn-on lead from source
Краткое содержание страницы № 12
Summed Bridged Configuration ● Lowest recommended impedance is 4W bridged mono. ● Mono or stereo input can be used for this configuration. ● Outputs can be configured for high-pass, low-pass, or full range operation. ● Output is configured as summed bridged which is ideal for subwoofer applications. Single Channel Bridged Configuration ● Lowest recommended impedance is 4W mono. ● Mono input must be used for this configuration. Only the Left input is used. ● Outputs can be configured for high-pas
Краткое содержание страницы № 13
Tri-Mode Three Channel Configuration ● Lowest recommended impedance is 2W stereo and 4W bridged mono. ● Stereo operation must be used. ● Outputs must be configured for full range operation. ● Output is configured stereo and summed bridged. ● Passive crossover frequencies must not overlap. WARNING! Failure to do so may result in damage to the amplifier. 12 ©2003 Directed Electronics, Inc.
Краткое содержание страницы № 14
AMPLIFIER INSTALLATION Choosing Mounting Locations The location of your amplifier will depend on several important issues. Due to the low pro- file size of the Orion amplifiers, there are many possible installation locations that will yield satisfactory amplifier performance. Always mount the amplifier in a place that protects the amplifier from the elements. In addition, mount the amplifier on a stable, flat surface. NOTE: Mounting amplifiers upside down is not recommended and may cause premat
Краткое содержание страницы № 15
Power for systems with a single amplifier can be supplied by most automotive electrical sys- tems. Systems with multiple amplifiers may require a higher capacity battery, alternator or the use of a storage capacitor. We strongly recommend the use of a Directed Audio Essentials power capacitor with an extra battery in larger stereo systems. Orion amplifiers generate a certain amount of heat as part of normal operation. Be sure the area around the amplifier is unobstructed to allow adequate air ci
Краткое содержание страницы № 16
Step 7 Disconnect the vehicle's battery ground terminal. Step 8 Connect power wires to the amplifier (ground first, then 12 V(+) and RGC). Step 9 Connect the RCA and speaker wires to the amplifier. Check the quality of your speakers and signal connections. This will determine the ultimate per- formance of your Orion amplifier. Refer to the Signal Input and Output Level Controls and Speaker Connections sections of this guide for correct wiring instructions. Step 10 Reconnect the ground terminal
Краткое содержание страницы № 17
Adjusting the Sound of the System Once you have checked the system's operation, adjust the sound of the system. Adjusting the sound of the system is accomplished by setting the level controls and adjusting the internal crossovers. Step 1 Turn the signal source volume control all the way down. Set any tone con- trols to their flat or defeated positions. This includes the loudness control. Step 2 Turn the level controls of the amplifier to their minimum positions. Step 3 Choose music with high dyn
Краткое содержание страницы № 18
Troubleshooting Tips Symptom Probable Cause Action To Take No output Low or no remote turn-on Check remote turn-on voltage at voltage amplifier and repair as needed. Fuse blown Check power wire's integrity and check for speaker shorts. Fix as needed and replace fuse. Power wires not connected Check power wire and ground connections and repair or replace as needed. Audio input not connected Check RCA connections and repair or replace as needed. Speaker wires not Check speaker wires and re
Краткое содержание страницы № 19
Symptom Probable Cause Action To Take Distorted output Internal crossover not set Readjust crossovers. Refer to the properly for speakers Internal Crossover Configuration section of this guide for detailed instructions. Speakers are blown Check system with known work ing speakers and fix or replace as needed. Poor bass response Speakers wired with wrong Check speaker polarity and fix polarity causing cancellation as needed. at low frequencies Crossover set incorrectly Reset crossovers. Refer
Краткое содержание страницы № 20
NOTES ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ _________________
