Руководство по эксплуатации JBL SCSSAT300

Краткое содержание страницы № 1

SCS-SAT300/200 OM 5/24/06 12:41 PM Page 3
THANK YOU FOR CHOOSING JBL
For more than 60 years, JBL ment that you expected – posted on our latest advance-
has been involved in every and that when you think ments, and helps us to better
aspect of music and film about purchasing additional understand our customers
recording and reproduction, audio equipment for your and build products that
from live performances to home, car or office, you will meet their needs and
the recordings you play in onc

Краткое содержание страницы № 2

SCS-SAT300/200 OM 5/24/06 12:41 PM Page 4 SPEAKER PLACEMENT FRONT SPEAKERS SURROUND SPEAKERS 1.5 – 1.8m 5 – 6 ft Placement for back speakers. † Placement for back surround speaker in a 6.1 system. Both the SCSSAT300 and the The rear wall is the required It is neither necessary nor SCSSAT200 loudspeakers placement for the back desirable to tilt the surround are designed to be used surround speakers in a 7.1- speakers to aim them down either singly or in a pair to channel system. The back tow

Краткое содержание страницы № 3

SCS-SAT300/200 OM 5/24/06 12:41 PM Page 5 ATTACHING THE SHELF STAND TO THE SPEAKER Prepare the speaker wire as conductor through the hole is snug. Follow the same described on page 5. Thread on the right looking at the procedure to connect the the two conductors through stand from the front. Push negative wire to its terminal. the two holes in the stand down on the red speaker Use the larger screw bracket. Make sure to pre- terminal and insert the bare (Hardware Bag A) in the + + serve the pr

Краткое содержание страницы № 4

SCS-SAT300/200 OM 5/24/06 12:41 PM Page 6 WALL-MOUNTING between the Metal Nut¡ 4 and the back of the Satellite 3 2 Speaker¶, using large needle-nose pliers until it is 1 firmly seated against the back of the Speaker¶ and has locked the Ball and Shaft£ and the Speaker¶ together. 8 Note that once the Metal Nut 5 ¡ is fully tightened, it may embed some marks on the back of the Satellite Speaker Important Safety Note: The Step 3: Slide the Molded Nut ¶. However, these marks customer is solely r

Краткое содержание страницы № 5

SCS-SAT300/200 OM 5/24/06 12:41 PM Page 7 Such damage would not be not to cross-thread. The ruin the intended effect by covered under the warranty. swiveling ball enables you to calling too much attention aim the speaker to one side to the information in those Step 7: Holding the Satellite or the other, or to tilt it up channels. Speaker¶ with both hands, or down. Although stereo reinsert the ball portion of Step 9: Once the speaker’s imaging may be improved the Ball and Shaft£ into orienta

Краткое содержание страницы № 6

SCS-SAT300/200 OM 5/24/06 12:41 PM Page 8 SYSTEM CONNECTION Connect each speaker to Configure your receiver or The SCSSAT300/200 should the corresponding speaker processor to reflect the cor- be set to “Small.” If your terminals on your receiver rect number of speakers in receiver allows you to set or amplifier. your system. If you have the crossover frequency added one SCSSAT300/200 between the subwoofer and If you are using a subwoofer, speaker to a 5.1-channel the speakers, select 100Hz or

Краткое содержание страницы № 7

SCS-SAT300/200 OM 5/24/06 12:41 PM Page 9 TROUBLESHOOTING If there is no sound from any tion. If the problem has fol- • Make sure the movie or of the speakers: lowed the speaker, consult TV show you are watching your dealer for further assis- is recorded in a surround • Check that receiver/ampli- tance or, if that is not possi- sound mode. If it is not, fier is on and a source is ble, visit www.jbl.com. check to see whether your playing. receiver/amplifier has other If the system plays at l

Краткое содержание страницы № 8

SCS-SAT300/200 OM 5/24/06 12:41 PM Page 2 SPECIFICATIONS SCSSAT300 SCSSAT200 Maximum Recommended Amplifier Power Maximum Recommended Amplifier Power 100 Watts 100 Watts Power Handling (Continuous/Peak) Power Handling (Continuous/Peak) 50W/200W 50W/160W Nominal Impedance 8 Ohms Nominal Impedance 8 Ohms Sensitivity 88dB @ 1 Watt/1 meter Sensitivity 86dB @ 1 Watt/1 meter Frequency Response 100Hz – 20kHz (–6dB) Frequency Response 110Hz – 20kHz (–6dB) Tweeter Tweeter 1/2" (13mm) Titanium-