Краткое содержание страницы № 1
PhotoBooth Setup Guide
009-1420-00
*009-1420-00*
Краткое содержание страницы № 2
IMPORTANT NOTES PhotoBooth is a combination of various manufacturer items, such as the camera and light. Please read all manufacturer documentation BEFORE following these instructions. Pay particular attention to all safety and regulatory information contained therein. InFocus is not liable for damage or injury caused by improperly using these items. Trademark information Apple, Mac and Facetime are trademarks or registered trademarks of Apple, Inc. Microsoft, Windows, PowerPoint, Excel
Краткое содержание страницы № 3
Contents IMPORTANT NOTES ............................................................................................................................................ 1 Trademark information ...................................................................................................................................... 1 Contents ............................................................................................................................................................ 2
Краткое содержание страницы № 4
Accessory Identification ® Canon EOS Camera Flash Unit Kit Kit Sync Cord Hot Shoe Speed Ring Wireless Remote Shutter Kit ® Canon AC Super Clamp L-Bracket Half Pole Adapter Kit 18-30” (46-74cm) Pivot Arm with Camera Bracket Mondopad™ Mobile Cart Softbox Accessory Identification Page 3
Краткое содержание страницы № 5
The accessories which you receive depend upon the part number you ordered: INF-5520-PB-C INF-PBKit-NOMP X X AC Adapter Kit X X Camera Kit X X Flash Unit Kit X X Half Pole X X Hot Shoe X X L-Bracket X X Pivot Arm X Mondopad** X Mondopad Mobile Cart X X Mondopad PC with Photobooth Software installed** X X Remote Shutter Kit X X Softbox X X Speed Ring X X Super Clamp X X Sync Cord ** Not shown on previous page. Page 4 Accessory Identification
Краткое содержание страницы № 6
PhotoBooth Assembly PhotoBooth PC Module Installation If you ordered INF-PBKit-NOMP, you will need to follow these instructions to replace your Mondopad PC. Otherwise skip to the next section. 1. Locate the Mondopad PC module on the back of the Mondopad panel. 2. Rotate the two antenna connectors counter-clockwise and disconnect them. Set them aside in a safe place. 3. Using the security allen wrench which was included with your Mondopad, remove the two security screws on the top and
Краткое содержание страницы № 7
2. Attach the speed ring to the flash unit by aligning the slots of the speed ring to the front of the flash unit and turning clockwise until it is fully attached. Move the blue “lock” slider button to the locked position. 3. Route the cables into each corner of the softbox. Page 6 PhotoBooth Assembly
Краткое содержание страницы № 8
4. Insert the cable ends into the speed ring. 5. Secure the Velcro at each corner of the softbox to complete its rectangle shape. PhotoBooth Assembly Page 7
Краткое содержание страницы № 9
Attaching the Flash Unit 1. Attach the L-bracket to the back of the Mondopad mobile cart. NOTE: If your mobile cart does not have holes drilled into it as per below, please contact InFocus Support at: www.infocus.com/support. 2. Attach the Mondopad panel to the mobile cart as per the manufacturer’s instructions and the INF-MOBCART addendum located on the InFocus Support site (Direct link: https://portal.infocus.com/support/Product%20Pages/downloads.aspx?mic=INF5520&on=do wnloads).
Краткое содержание страницы № 10
3. Attach the flash unit to the half pole using the knurled clamp screw. Tighten securely. Knurled Clamp Screw Tilt Head 4. Slide the half pole onto the L-bracket and adjust as needed. 5. Adjust the half pole above the Mondopad panel, allowing room for the camera. 6. Adjust the angle of the flash unit and softbox to accommodate the camera and your situation, using the flash unit tilt head. 7. Plug the power cord into the flash unit and route through the mobile cart post. 8. Plu
Краткое содержание страницы № 11
Attaching the Pivot Arm WARNING: Do not attach the camera to the arm until it is fully positioned and locked into place. 1. Insert the stud into the super clamp and attach the super clamp securely to the pivot arm. 2. Position the super clamp along the top vertical bar of the Mondopad frame and tighten securely. 3. Turn the large black adjustment knob on the pivot arm counterclockwise. All pivot points will become loose. 4. Position the arm similar to the image below and turn the a
Краткое содержание страницы № 12
Preparing the Camera Note: For this section, you will need the Canon AC adapter kit, the Canon camera, camera lens and an SD card (required). Mode Dial Power Switch Lens Focus Mode Switch SD Slot Battery Door 1. Insert a SD card (not included) into the camera’s SD slot on the right-hand side of the camera, being careful to align the SD card appropriately. 2. Attach the lens, by aligning the dots and turning the lens clockwise until an audible click is heard. 3. Set the Lens Fo
Краткое содержание страницы № 13
7. Attach the camera to the pivot arm securely. 8. Carefully loosen the pivot arm adjustment knob to make final adjustments to the camera’s position, being very careful of the camera. WARNING: Turning the adjustment knob will release the arm pivot points. Damage to the camera could occur, if the camera is allowed to fall. 9. Connect the AC adapter to the AC power cord. 10. Plug the other end of the AC power cord to a power strip or power outlet. Page 12 PhotoBooth Assembly
Краткое содержание страницы № 14
Preparing the Wireless Trigger 1. Slide the battery door off. 2. Insert a 12V battery into the wireless receiver, being careful of the battery orientation, and slide the battery door back on. 3. Slide the wireless receiver onto the bottom of the hot shoe. 4. Slide the hot shoe to the camera. Note: The receiver can also be attached using Velcro tape to the back of Mondopad. 5. Attach the sync cable from the sync socket on the back of the flash unit to the hot shoe. Note: Secure exce
Краткое содержание страницы № 15
Taking a PhotoBooth Photo Cell Button Power Switch 1. Turn Mondopad ON. 2. Turn the camera’s power switch to ON and the Mode Dial to M (“Manual”). 3. Turn the flash unit’s power switch to the ON position. 4. Verify that the Cell button LED is off. If the Cell button LED is lit, press the Cell button to turn it off. 5. Press the receiver’s power button and slide the slider from Hold to Ready. 6. Slide the wireless transmitter button to Single/Bulb. 7. When ready, click the transmitt
Краткое содержание страницы № 16
Framing Images 1. From the Mondopad home page, navigate to View & Share. 2. Open an image file. Note: Images created with PhotoBooth appear in the PhotoBooth folder. 3. Tap Annotations. Framing Images Page 15
Краткое содержание страницы № 17
7. Tap Frames from the menu. 8. Tap the frame you want for the image and tap OK. Page 16 Framing Images
Краткое содержание страницы № 18
9. To save the image, tap Save JPG. 10. Type a name in the File Name field and tap Save. 11. Saved images can be viewed in the View and Share folder. Framing Images Page 17
Краткое содержание страницы № 19
Note: Saved images can also be found in the following folder: Documents>Mondopad Documents. Adding New Frame Files to Mondopad 1. From within the Mondopad software, navigate and login to Extras. 2. Tap Minimize to go to the Windows Desktop. 3. Navigate to the Zoos>Files>Frames folder. 4. Copy and paste your PNG images from a thumb drive into this folder. Page 18 Framing Images
Краткое содержание страницы № 20
Note: For best results, PNG images should be the same resolution as the Mondopad (1920 x 1080) and have transparent centers. Framing Images Page 19
