Руководство по эксплуатации JL Audio EVOLUTION TR400-CXI

Краткое содержание страницы № 1

®
Stealthbox
INSTALLATION GUIDE START
HERE
for the
Read the instructions completely, before the start of
SB-GM-BURBSCNSL/10W3v2 the install.
➔ ➔ ➔
This Stealthbox Enclosure install does require per-
(2003-Up Chevrolet Suburban,Tahoe,
manent modification to the OEM inner console.
Silverado &
GMC Yukon,YukonXL, Sierra with front
bucket seats and center console)
STEP 1: Engage the emergency brake. STEP 2: Moving down to the top portion of the
center console. Pull the upper storage pocket panel
Pl

Краткое содержание страницы № 2

*CAUTION* Cont. The vehicle that you are working on might be From equipped with side impact air bags.To remove the Previous Page front seats, please follow these required procedures. 1)Disconnect the ground wire from the negative side of the battery. ➔ ➔➔ ➔ 2)Let the vehicle sit for 15 minutes.This allows the air bags to discharge. 3)Now you can remove the front seats and discon- nect the air bag wire. If you are not comfortable with disconnecting the air bag wires.This install can be accomplish

Краткое содержание страницы № 3

Cont. From Previous Page ➔ ➔➔➔ STEP 12: Remove the OEM wire harness from STEP 13: With the OEM wiring harness out of STEP 14: With the OEM carpet and the STEP 15: Thread the supplied pair of socket cup the plastic track.Wrap the OEM wiring in black the way, you need to cut the carpet. jute(sound deadening) cut out. Position the supplied set screws into the Stealthbox. Leaving about 1/4” tape. pair of 3”x3” wax squares in place. exposed. SIDES: From the tape outline of the center con sole, measur

Краткое содержание страницы № 4

➔ Cont. From Previous Page ➔ ➔➔➔ STEP 20: Back out the socket cup set screws to expose 1-1/2”. Carefully guide the socket cup set screws through the STEP 21: With the OEM console out of the vehi- STEP 22: *SUVs or trucks with rear stereo STEP 23: To remove the OEM woofer enclosure. mounting holes, in the floor. cle.You need to remove the outside cosmetic con- controls* Start by drilling out these pair of rivets. Located on sole from the inside structure support console. From under the vehicle, s

Краткое содержание страницы № 5

Cont. From Previous Page ➔ ➔➔➔ STEP 28: This is a view of the driver’s side, front STEP29: The mark line needs to follow around STEP 30: The mark line needs to jet up slightly to STEP 31: These next three STEPS are just area. this mounting leg. Follow this inside edge to the this front edge. Mark across this edge from the dri- mirroring STEPS 27,28 & 29.This is for the front. ver’s side to the passenger’s side. passenger’s side of the inner console. The mark lines needs to follow this edge forwa

Краткое содержание страницы № 6

Cont. From Previous Page ➔ ➔ ➔➔ STEP 36: This the view of the passenger’s side, STEP 37: This is the view of the upper pocket, STEP 38: The passenger’s side mark line goes STEP 39: The driver’s side mark line goes from from STEP 29. that needs to be removed. from the bottom mark line from STEP 37, angling the bottom mark line from STEP 37, angling up to up to the upper corner of this exposed upper wall. this upper corner of this exposed upper wall. The mark lines follow the bottom, using this ed

Краткое содержание страницы № 7

Cont. From Previous Page ➔ ➔ ➔ STEP 45: With the upper storage pocket in hand STEP 44: The pair of 10mm bolts that where STEP 46: Reconnect the rear stereo controls and from STEP 4, reconnect the 12v outlets.Then snap removed in STEP 5, need to be replaced.You may 12v plug from STEP 22. the upper storage pocket back into place. have to reposition the OEM console, to have it line Also reconnect the white plug with the lever from up like factory. STEP 9. ➔ ➔ STEP 47: Replace the rear of the outer

Краткое содержание страницы № 8

Cont. From Previous Page CONGRATULATIONS! INSTALL COMPLETE. ➔ ➔ ➔ Included Hardware: STEP 50: Snap the dash trim panel back into place STEP 51: Place the front seats back into place (2) 3/8” Split Lock Washer from STEP 3. from STEP 1. (2) 3/8” x 1-1/4” Fender Washer Remember to reconnect the wiring connection (2) 3/8”-16, 2-1/4” Socket Cup Set Screws under the seats. (2) 3/8” - 16 Hex Nuts (2) 3”x 3” Wax Squares Difficulty Of Installation: Specifications: Mid/High Frequency Driver Information: E