Краткое содержание страницы № 1
ST-200
Techno Strobe™ 200
USER MANUAL
th
Chauvet, 3000 N 29 Ct, Hollywood, FL 33020 U.S.A
(800) 762-1084 – (954) 929-1115
FAX (954) 929-5560
www.chauvetlighting.com
Краткое содержание страницы № 2
TABLE OF CONTENT BEFORE YOU BEGIN........................................................................................................................................................... 3 WHAT IS INCLUDED................................................................................................................................................................................ 3 UNPACKING INSTRUCTIONS ........................................................................................
Краткое содержание страницы № 3
BEFORE YOU BEGIN What is included ST-200 Power cord with plug 200w Xenon lamp (Installed) Warranty Card & Manual Unpacking Instructions Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that all parts are present, and have been received in good condition. Notify the shipper immediately and retain packing material for inspection if any parts appear damaged from shipping or the carton itself shows signs of mishandling. Save the carton an
Краткое содержание страницы № 4
INTRODUCTION Features • audio sensitivity adjustment • manual strobe speed control • manual strobe intensity control • 1 year warranty Product Overview Hanging bracket Gel Holder Connect to other ST-200 strobes for unison operation Fuse compartment Audio sensitivity ¼” Phone plug adjustment Strobe speed for simple adjustment variable speed remote control Strobe intensity (Use SC-1000M adjustment or CH-751) ST-200 User Manual 4 Revision: 2004-11-02/11:23
Краткое содержание страницы № 5
SETUP Lamp The xenon 200 watt lamp comes pre-installed from the factory. Warning! When replacing the lamp, please wait 15 minutes after powering down to allow the unit to cool down! Always disconnect from main power prior to lamp replacement. Do not touch the envelope (glass area) of the bulb with bare hands. If this happens, clean the lamp with alcohol and wipe it with a lint free cloth before installation. LAMP INSTALLATION 1) Unscrew the three most left and right screws on the back
Краткое содержание страницы № 6
Setup Mounting ORIENTATION This fixture may be mounted in any position provided there is adequate room for ventilation. It is also possible to stand this fixture using the removable feet provided. RIGGING Figure 1 - Hanging Bracket It is important never to obstruct the fan or vents pathway. Mount the fixture using, a suitable “C” or “O” type clamp. Adjust the angle of the fixture by loosening both knobs and tilting the fixture. After finding the desired position, retighten both knobs
Краткое содержание страницы № 7
OPERATING INSTRUCTIONS Operating Modes • A stand-alone mode will listen to sound and strobe to the beat. • Master/Slave output provides for unison triggering of chained strobes. STAND ALONE The Stand Alone mode is activated automatically when the fixture is absent of a CH-751 or a SC- 1000M controller. The strobe speed, strobe intensity and the microphone sensitivity can all be adjusted and they are located on the bottom of the ST-200. UNISON STROBE The Unison strobe mode will allow
Краткое содержание страницы № 8
APPENDIX Maintenance To maintain optimum performance and minimize wear fixtures should be cleaned frequently. Usage and environment are contributing factors in determining frequency. As a general rule, fixtures should be cleaned at least twice a month. Dust build up reduces light output performance and can cause overheating. This can lead to reduced lamp life and increased mechanical wear. Be sure to power off fixture before conducting maintenance. Unplug fixture from power. Use a vacu
Краткое содержание страницы № 9
Appendix General Troubleshooting Applies to Foggers Dimmers Symptom Solution(s) Lights & Snow Controllers & Chaser Auto shut off Check fan thermal switch reset Beam is very dim or not Clean optical system or replace lamp bright Check 220/110v switch for proper setting Breaker/Fuse keeps Check total load placed on device blowing Chase is too slow Check users manual for speed adjustment Device has no power Check for power on Mains. Check device’s fuse. (intern
Краткое содержание страницы № 10
Appendix Technical Specifications WEIGHT & DIMENSIONS Length.............................................................................................................................. 330 mm (13 in) Width .............................................................................................................................. 205 mm (8.1 in) Height .................................................................................................................................100
