Краткое содержание страницы № 1
Bullet
I B8354-C Network Camera
User’s Manual
Outdoor • Day & Night • Weather-proof • Cable Management
Rev. 1.0
Краткое содержание страницы № 2
VIVOTEK Table of Contents Overview .....................................................................................................................................................4 Revision History ...................................................................................................................................... 4 Read Before Use .....................................................
Краткое содержание страницы № 3
VIVOTEK Electromagnetic Compatibility (EMC) .......................................................................................................198 Overview VIVOTEK IB8354-C, equipped with a 1.3MP sensor enabling viewing resolution of 1280x1024 at a smooth 30 fps, is a best-in-class, bullet-style network camera designed for diverse outdoor applications. In order to adapt to constantly changing outdoor lighting conditions, the IB8354-C features a removable IR-cut filter as well as improve
Краткое содержание страницы № 4
VIVOTEK Read Before Use The use of surveillance devices may be prohibited by law in your country. The Network Camera is not only a high-performance web-ready camera but can also be part of a flexible surveillance system. It is the user’s responsibility to ensure that the operation of such devices is legal before installing this unit for its intended use. It is important to first verify that all contents received are complete according to the Package Contents listed below. Take note of the
Краткое содержание страницы № 5
VIVOTEK Front Panel Lens IR LEDs Rear Panel Reset Button MicroSD/SDHC Card Slot General I/O Terminal Block Ethernet 10/100 RJ45 Plug GND DI User's Manual - 5
Краткое содержание страницы № 6
VIVOTEK Hardware Installation If you prefer installing a MicroSD card as onboard storage: 1. Loosen the waterproof connector, and then remove the rubber seal, and the waterproof connector. 2. Loosen and open the rear cover. 3. Install a MicroSD/SDHC card. 4. Tear down the aluminum foil vacuum bag and take out the desiccant bag. Attach the supplied desiccant bag to the inner side of the Network Camera. (Please replace the desiccant bag with a new one every time you open the rear cover.) 5.
Краткое содержание страницы № 7
VIVOTEK General I/O Terminal Block This Network Camera provides two digital input pins that can be connected to external sensor devices. The pin definitions are described below. GNDDI DI/DO Diagram Please refer to the following illustration for the connection method. +12V PIN 2 Digital input PIN 1 Ground User's Manual - 7
Краткое содержание страницы № 8
VIVOTEK 6. Install and tighten the camera's rear cover. 7. Tighten the rubber seal, seal clamp, and cap nut of the waterproof connector. 6 7 8. Pass the cables through the center of the ball swivel mount bracket, one at a time. 9. Fasten the bracket to the camera using 3 hex socket screws. 9 8 NOTE: The camera weighs up to 1.28 kgs. Make sure the mounting surface can support this camera. IMPORTANT: Whenever you want to open the camera canister, loosen the waterproof cable gland before y
Краткое содержание страницы № 9
VIVOTEK 10. Loosen the fastening ring on the mount bracket, and aim the camera at the area of your interest. When done, tighten the fastening ring. Fastening ring 75º Tilt 360º Pan 11. Secure the Network Camera to a wall or ceiling. Ceiling Mount Wall Mount User's Manual - 9
Краткое содержание страницы № 10
VIVOTEK Hardware Reset Reset Button The reset button is used to reset the system or restore the factory default settings. Sometimes resetting the system can return the camera to normal operation. If the system problems remain after reset, restore the factory settings and install again. Reset: Press the recessed reset button. Wait for the Network Camera to reboot. Restore: Press and hold the reset button until the status LED rapidly blinks. Note that all settings will be restored to factor
Краткое содержание страницы № 11
PARTITION PARTITION LINK RECEIVE POWER COLLISION 1 2 3 4 5 LINK RECEIVE POWER COLLISION 1 2 3 4 5 VIVOTEK Network Deployment General Connection (PoE) When using a PoE-enabled switch The Network Camera is PoE-compliant, allowing transmission of power and data via a sin- gle Ethernet cable. Follow the below illustration to connect the Network Camera to a PoE- enabled switch via Ethernet cable. PoE Switch When using a non-PoE switch Use a PoE power injector (optional) to connect between the Netwo
Краткое содержание страницы № 12
PARTITION RELCINEKIVE POWER COLLISION 1 2 3 4 5 VIVOTEK Internet connection via a router Before setting up the Network Camera over the Internet, make sure you have a router and follow the steps below. 1. Connect your Network Camera behind a router, the Internet environment is illustrated below. Regarding how to obtain your IP address, please refer to Software Installation on page 14 for details. IP address : 192.168.0.3 WAN (Wide Area Network ) Subnet mask : 255.255.255.0 Router IP address
Краткое содержание страницы № 13
VIVOTEK Configure the router, virtual server or firewall, so that the router can forward any data com- ing into a preconfigured port number to a network camera on the private network, and allow data from the camera to be transmitted to the outside of the network over the same path. From Forward to 122.146.57.120:8000 192.168.2.10:80 122.146.57.120:8001 192.168.2.11:80 ... ... When properly configured, you can access a camera behind the router using the HTTP request as follows: http://122.1
Краткое содержание страницы № 14
VIVOTEK Software Installation Installation Wizard 2 (IW2), a software included in the product CD, helps you set up your Network Camera on the LAN. IW2 1. Install IW2 under the Software Utility directory from the software CD. Installation Double-click the IW2 shortcut on your desktop to launch the program. Wizard 2 2. The program will conduct an analysis of your network environment. After your network environment is analyzed, please click Next to continue the program. 3. The program
Краткое содержание страницы № 15
VIVOTEK Ready to Use 1. A browser session with the Network Camera should prompt as shown below. 2. You should be able to see live video from your camera. You may also install the 32-channel recording software from the software CD in a deployment consisting of multiple cameras. For its installation details, please refer to its related documents. User's Manual - 15
Краткое содержание страницы № 16
VIVOTEK Secure the Shooting Angle When you are done with tuning the field of view and obtain a satisfactory image, tighten the fastening ring and the 3 small hex screws on the ball-swivel bracket. NOTE: Orient the camera so that the protruding edge of its sunshield is positioned against the direction of direct sunlight. Protruding edge 16 - User's Manual
Краткое содержание страницы № 17
VIVOTEK Accessing the Network Camera This chapter explains how to access the Network Camera through web browsers, RTSP players, 3GPP-compatible mobile devices, and VIVOTEK recording software. Using Web Browsers Use Installation Wizard 2 (IW2) to access the Network Cameras on LAN. If your network environment is not a LAN, follow these steps to access the Netwotk Camera: ® 1. Launch your web browser (e.g., Microsoft Internet Explorer or Mozilla Firefox). 2. Enter the IP address of the Network
Краткое содержание страницы № 18
VIVOTEK ► By default, the Network Camera is not password-protected. To prevent unauthorized access, it is highly recommended to set a password for the Network Camera. For more information about how to enable password protection, please refer to Security on page 75. ® ► If you see a dialog box indicating that your security settings prohibit running ActiveX ® Controls, please enable the ActiveX Controls for your browser. 1. Choose Tools > Internet Options > Security > Custom Level. ® 2. Loo
Краткое содержание страницы № 19
VIVOTEK IMPORTANT: Currently the Network Camera utilizes 32-bit ActiveX plugin. You CAN NOT open a • management/view session with the camera using a 64-bit IE browser. If you encounter this problem, try execute the Iexplore.exe program from C:\Windows\ • SysWOW64. A 32-bit version of IE browser will be installed. On Windows 7, the 32-bit explorer browser can be accessed from here: • C:\Program Files (x86)\Internet Explorer\iexplore.exe If you open a web session from the IW2 utility, a 3
Краткое содержание страницы № 20
VIVOTEK Using RTSP Players To view the streaming media using RTSP players, you can use one of the following players that support RTSP streaming. Quick Time Player VLC media player VLC media player 1. Launch the RTSP player. mpegable Player 2. Choose File > Open URL. A URL dialog box will pop up. 3. The address format is rtsp://:/ As most ISPs and
