Краткое содержание страницы № 1
OUTDOOR DOME CAMERA
INSTRUCTIONS
TK-C2201WPU
(For USA and Canada)
TK-C2201WPE
(For Europe)
For Customer Use:
Enter below the Serial No. which is located on the
body. Retain this information for future reference.
Model No. TK-C2201WPU,TK-C2201WPE
Serial No.
.
LST0979-001B
Краткое содержание страницы № 2
Introduction Contents Introduction Contents ............................................................................................................. 2 Features ............................................................................................................. 3 Operating Precautions ....................................................................................... 4 Name of Parts .................................................................................................
Краткое содержание страницы № 3
Introduction Thank you for purchasing this product. Before use, please read this "INSTRUCTIONS" and the information materials included to ensure proper use of this product. These instructions are for TK-C2201WPU/TK-C2201WPE. TK-C2201WPE is not evaluated by UL. Features v Easy DAY/NIGHT function (TK-C2201WPU) v DAY/NIGHT surveillance with auto IR cut filter on/off (Color/B&W shooting) (TK- C2201WPE) v 3D noise reduction (3DNR) v 4 areas privacy mask v Built-in display mode (CRT or LCD selectable)
Краткое содержание страницы № 4
Introduction Operating Precautions m Storage and Location of Use v Do not install the camera in the following places. - In a place with vapor or oil, for example in a kitchen. - When the ambient temperature rises above or falls below the acceptable range (from -10 f to 50 f) - In a place at which corrosive gases are emitted. - Near a source of radiation, X-rays, strong radio waves or magnetism. - In a place subject to vibration. - In a place with excessive dirt. v Using this unit in the vicinity
Краткое содержание страницы № 5
Introduction m Disclaimer v We will not be responsible for any inconveniences or disturbances caused in the event of privacy invasion as a result of camera footages of this product. m Others v When using this camera with [AGC] set to "MID" or "HIGH", the sensitivity increases automatically for dark images and the screen may appear grainy, but this is not a malfunction. v If the DAY/NIGHT switch is turned to "AUTO", the mode changes automatically to black and white in dark places. As the sensitiv
Краткое содержание страницы № 6
Introduction Name of Parts Camera . F G H I A J B K C D E . A Mounting Hole 2 2 (A page 14) B Fall Prevention Wire Mounting Screw (A page 14) C Conduit Plug/Hole (side) (A page 21) D Dome Cover (A page 13) E Inner Dome (A page 13) F Video signal output connector (BNC) (A page 10) (A page 15) 6
Краткое содержание страницы № 7
Introduction G Protection Cover (A page 15) H Power Supply Cable (A page 11) (A page 15) I Hole for Connecting Cables, Conduit Hole (A page 20) J Base (A page 19) K Dome Cover Fastening Screw 23 (A page 13) 7
Краткое содержание страницы № 8
Introduction Name of Parts (Continued) Camera (Interior) The dome cover and inner dome are removed. . J M K L A N B O C D P E F ADJ Q 1 F R MENU G S H SET I MONITOR . A Focus Adjustment Ring (A page 25) B Zoom Adjustment Ring (A page 25) C Rotation Knob (A page 24) D Fall Prevention Wire (To prevent the dome cover from dropping) (A page 13) E Camera Unit Fastening Screw 22 (A page 19) 8 F ADJ DIPSW D/N AUTO 1 OFF BLC OFF 2 ON MONITOR LCD 3 CRT TYPE NOT USED 4 SEE INSTRUCTION MANUAL
Краткое содержание страницы № 9
Introduction F Space for Inserting Heater When mounting the heater (sold separately: KA-ZH215U), read the instruction manual of the heater before mounting. G Power Supply Connector for Heater For connecting to the power supply connector of the heater. H Tilt Fastening Screw 22 (A page 24) I [MONITOR] Terminal (RCA pin) (A page 23) J Lug Plate (A page 16) K Space for Inserting Silica Gel (A page 16) L Focus Adjust Gear (A page 25) M Shooting Direction Mark (A page 24) N Pan Center Mark (A page 24
Краткое содержание страницы № 10
Setup About Connection Cables The maximum connection distance varies with the type of cable used. v Be sure to turn off the power of devices before connecting cables. . To video Signal Cable To Power Supply . v Connect to AC 24 V power supply if using the heater (sold separately: Memo KA-ZH215U). Video signal cable (coaxial cable) Connect a 75 K coaxial cable (BNC) such as RG-59 to the video signal output connecter (BNC). 10
Краткое содержание страницы № 11
Setup DC 12 V or AC 24 V power supply cable Connect the power cord to the DC 12 V or the AC 24 V power supply. The unit is to be powered by a UL Listed Class 2 power supply only. (For USA and Canada) The AC 24 V and DC 12 V power supply shall conform to the following: UL Listed Class 2 power supply only, Class 2 not wet and Class 3 wet wiring (For USA) Isolated power supply only (For Europe) This installation shall be in accordance with the National Electrical Code, ANSI/ NFPA 70. The following
Краткое содержание страницы № 12
Setup Setting the Switches Before mounting the camera, set the function setting switches on the camera. To set the switches, use a fine-tipped screwdriver. . DIP Switch Settings Chart 1 D/N AUTO OFF 2 BLC OFF ON 3 MONITOR LCD CRT TYPE 4 NOT UESD - - Function selection switches . 1 [D/N AUTO/OFF] Day & Night Switch Set this to "AUTO" when shooting a subject with continually changing brightness (day/night). The image switches to color when the subject is bright, and black and white when it is dar
Краткое содержание страницы № 13
Installation Mounting the Camera Selecting a mounting method v Mount directly to the ceiling or on the wall ( A page 13) v Mounting the Camera Using the Conduit Hole at the Bottom of the Base (A page 19) v Mounting the Camera Using the Conduit Hole at the Side of the Base (A page 21) v Mounting the Camera using the Electrical Box ( A page 22) When mounting the camera to the ceiling, ensure to wear safety glasses Memo to protect the eye from any falling objects. Mounting the camera directly to th
Краткое содержание страницы № 14
Installation Mounting the Camera (Continued) m Mounting the Camera Unit 1 Make a hole ( Φ30 mm) in the ceiling using the template provided 2 Mount the fall prevention wire for connecting the camera unit to the ceiling The fall prevention wire is not provided. Prepare a wire, taking into due consideration the length, strength, pull and material (insulating). ① Remove the fall prevention wire fastening screw on the bottom of the camera unit to mount the fall prevention wire. ② Mount the fall preve
Краткое содержание страницы № 15
Installation m Connecting the cable For safety reasons, turn on the power only after all the connection is complete. The status indicator lights up when the camera is turned on. 1 Connect the coaxial cable ( A page 10) Lower the protection cover and connect the connectors. Upon connecting, restore the protection cover to cover the connectors. This will isolate and protect the metallic parts of the connectors. 2 Connect the power supply cable ( A page 11) 3 Wrap insulation tapes around the connec
Краткое содержание страницы № 16
Installation Mounting the Camera (Continued) m Process after connection Fill the conduit hole and mounting holes with sealing agent and insert the silica gel. 1 Fill the conduit hole and the screw mounted holes (2 locations) with sealing agent (GE silicon) Seal the holes completely. Failure to do so may cause water or moisture Note to enter, thereby fogging the lens and dome cover. 2 Remove the silica gel (provided) from its bag and insert in the position as shown in the diagram . 1 2 Sealing ma
Краткое содержание страницы № 17
Installation m Adjusting images After mounting is completed, adjust the images while checking the actual image. (A page 23) m Mounting the Dome Cover Attach the dome cover back when all settings are finished. 1 Mount the inner dome Mount the inner dome in a way that supports the tilt direction of the lens. Insert the inner depression of the inner dome into the protruding parts beside the fastening screw. Push it in until it is fixed by the catches (2 locations). . Protruding part Catches ( 2)
Краткое содержание страницы № 18
Installation Mounting the Camera (Continued) 2 Mount the dome cover ① Clean the dust and dirt on the dome cover. ② Align the position marks (3 locations) on the camera unit and dome cover, followed by pressing in directly to mount the cover. ③ Tighten the dome cover fastening screw. . Position alignment mark (x 3) Dome cover Dome cover protective sheet . v Note Ensure that the silica gel (provided) has been inserted before mounting the dome cover. v Be sure to secure the dome cover firmly. If i
Краткое содержание страницы № 19
Installation Mounting the Camera Using the Conduit Hole at the Bottom of the Base Conduit hole: G3/4-14 UNC (TK-C2201WPU), M25 (TK-C2201WPE) 1 Remove the dome cover and inner dome (A page 13) 2 Remove the camera unit from the base and mount the fall prevention wire to the camera unit ① Loosen the camera unit fastening screw (2 locations) with a screwdriver. ② Press the catch (2 locations) inwards and remove the camera from the base. ③ Remove the fall prevention wire fastening screw on the base t
Краткое содержание страницы № 20
Installation Mounting the Camera (Continued) 3 Wind the sealing tape Wind the sealing tape around the pipe junction (where the conduit hole thread lines with the pipe screw hole) two or more times. 4 Mount the base to the pipe Turn and screw the base unit to the pipe in the clockwise direction. When screwing the pipe, do not screw beyond 12 mm. Doing so can Note damage the camera interior. 5 Secure the base unit to the ceiling Use the M4 screw (x2) to secure the base firmly to the ceiling. v Not
