Краткое содержание страницы № 1
FIXED DOME CAMERA
INSTRUCTIONS
TK-C2201U
TK-C2201E
For Customer Use:
Enter below the Serial No. which is located on the
body. Retain this information for future reference.
Model No. TK-C2201U,TK-C2201E
Serial No.
.
LST0952-001A
Краткое содержание страницы № 2
Introduction Contents Introduction Contents ............................................................................................................. 2 Features ............................................................................................................. 3 Operating Precautions ....................................................................................... 4 Name of Parts .................................................................................................
Краткое содержание страницы № 3
Introduction Thank you for purchasing this product. Before use, please read this "INSTRUCTIONS" and the information materials included to ensure proper use of this product. These instructions are for TK-C2201U/TK-C2201E. Features v Easy DAY/NIGHT function v 3D noise reduction (3DNR) v 4 areas privacy mask v Built-in display mode (CRT or LCD selectable) How to read this manual Conventions and symbols : Indicates operating precautions. Note Memo : Indicates reference data regarding limitations on
Краткое содержание страницы № 4
Introduction Operating Precautions m Storage and Location of Use v This camera has been designed for indoor use. It cannot be used outdoors. v Do not install the camera in the following places. - In a place exposed to rain or moisture. - In a place with vapor or oil, for example in a kitchen. - When the ambient temperature rises above or falls below the acceptable range (from -10 f to 50 f) - In a place at which corrosive gases are emitted. - Near a source of radiation, X-rays, strong radio wave
Краткое содержание страницы № 5
Introduction m Disclaimer v We will not be responsible for any inconveniences or disturbances caused in the event of privacy invasion as a result of camera footages of this product. m Others v When using this camera with [AGC] set to "MID" or "HIGH", the sensitivity increases automatically for dark images and the screen may appear grainy, but this is not a malfunction. v If the Easy DAY/NIGHT switch is turned to "AUTO", the mode changes automatically to black and white in dark places. As the sen
Краткое содержание страницы № 6
Introduction Name of Parts Camera (Interior) The dome cover and inner dome are removed. Refer to "Mounting the camera directly to the ceiling or on the wall" ( A page 13) step 2 to 3 on the removal methods. . G A B H C I J D K E L F. ADJ M F MENU N SET . A Focus Adjustment Ring (A page 19) B Zoom Adjustment Ring (A page 19) C Fall Prevention Sheet (A page 13) D Rotation Knob (A page 18) E [MONITOR] Terminal (RCA pin) (A page 17) 6
Краткое содержание страницы № 7
Introduction F Tilt Fastening Screw (A page 18) G Focus Adjust Gear (A page 19) H Shooting Direction Mark (A page 15) (A page 18) I Pan Center Mark (A page 18) J Rotation Center Mark (A page 18) K Function Selection Switches (A page 9) L [MENU] Button Display the menu screen. Refer to the attached manual "MENU SETTING" for more details about setting the menu. M Status Indication Lamp Lights up when the power is turned on. N [J, K, H, I]/[SET] Button This allows user to select menu screens and ch
Краткое содержание страницы № 8
Introduction Name of Parts (Continued) Camera . D E F A G H B C . A Mounting Hole 2 2 (A page 15) B Dome Cover (A page 13) C Inner Dome (A page 13) D Video Signal Output Connector (BNC) (A page 14) E Protection Cover (A page 14) F Power Supply Cable (A page 11) G Wiring Hole (A page 16) H Fall Prevention Wire Mounting Screw (A page 14) 8
Краткое содержание страницы № 9
F. ADJ MENU Setup Setting the Switches Before mounting the camera, set the function setting switches on the camera. To set the switches, use a fine-tipped screwdriver. Function selection switches DIP SW D/N AUTO 1 OFF BLC OFF 2 ON MONITOR LCD 3 CRT TYPE NOT USED 4 SEE INSTRUCTION MANUAL DIP Switch Settings Chart . 1 [D/N AUTO/OFF] Easy Day & Night Switch Set this to "AUTO" when shooting a subject with continually changing brightness (day/night). The image switches to color when the subject is b
Краткое содержание страницы № 10
Setup About Connection Cables The maximum connection distance varies with the type of cable used. v Be sure to turn off the power of devices before connecting cables. . To video Signal Cable To DC 12 V or AC 24 V Power Supply . Video signal cable (coaxial cable) Connect a RG-59 75 K coaxial cable (BNC) to the video signal output connecter (BNC). 10
Краткое содержание страницы № 11
Setup DC 12 V or AC 24 V power supply cable Connect the power cord to the DC 12 V or the AC 24 V power supply. The following table shows the connection distances when 2-core VVF (vinyl- insulated vinyl sheath cables) are used. (Reference value) Conductor diameter Maximum connection Maximum connection distance: DC 12 V distance: AC 24 V Φ 1.0 mm (AWG 18) 50 m (160 ft) 130 m (420 ft) Φ 1.6 mm (AWG 14) 140 m (450 ft) 350 m (1100 ft) Φ 2.0 mm (AWG 12) 220 m (720 ft) 550 m (1800 ft) v If thin cables
Краткое содержание страницы № 12
Installation Mounting the Camera Mounting the camera to the ceiling v When mounting the camera to the ceiling, ensure to wear safety Note glasses to protect the eye from any falling objects. v It maybe mandatory to mount an embedded cover in the ceiling (recessed bracket) in certain areas. If an embedded cover (recessed bracket) is required, ensure it is securely mounted before installing the camera. v Please refer to the instruction manual for the embedded cover (recessed bracket) in use for de
Краткое содержание страницы № 13
Installation Mounting the camera directly to the ceiling or on the wall When mounting to a wall, replace areas indicated as "ceiling" in the procedures by "wall". m Setup 1 Open a hole in the ceiling ( Φ 30 mm, 1-1/8 inches), and draw the fall prevention wire, power supply cable and coaxial cable out from the ceiling (fall prevention wire is not included) . 30 mm Power cable (1-1/8 inches) Fall prevention wire (not supplied) Approx. 100 mm (3-7/8 inches) Coaxial cable . 2 Remove the dome cover A
Краткое содержание страницы № 14
Installation Mounting the Camera (Continued) m Connection 1 Attach the fall prevention wire from the ceiling to the camera (fall prevention wire is not included) 2 Connect the coaxial cable ( A page 10) Lower the protection cover and connect the connectors. Upon connecting, restore the protection cover to cover the connectors. This will isolate and protect the metallic parts of the connectors from the ceiling structures. 3 Connect the power supply cable ( A page 11) 4 Wrap insulation tapes aroun
Краткое содержание страницы № 15
Installation m Mounting 1 Align (ñ) with the shooting direction, and mount the camera onto the ceiling Mounting screw (not included) Note v The diameter of the attachment hole is Φ 4.5 mm (3/16 inch). v Do not use flathead screws. v When using an impact screwdriver, do not tighten the screws fully. Tighten using your hand instead. Failure to do so may damage the outer case. . . m Adjusting images After mounting is completed, adjust the images while checking the actual image. "Adjusting Image" (A
Краткое содержание страницы № 16
Installation Mounting the Camera (Continued) Mount by allowing the cable to exit from the side When mounting the camera to the ceiling or a wall, it is possible to guide the cable from the side without opening any holes. The basic mounting method is identical to steps in "Mounting the camera directly to the ceiling or on the wall" ( A page 13) . 1 Cut both ends of the extraction hole for the cable with a nipper and break off the excess material using tools such as long-nose pliers . . 2 Pull out
Краткое содержание страницы № 17
Adjustment Adjusting Image After mounting the camera, adjust the images while looking at the actual image. Discharge the static electricity from your body by touching the metallic part of the monitor terminal before handling the camera as static electricity may cause the camera to malfunction. 1 Mount the monitor Connect the monitor terminal of this camera to a test monitor to adjust the camera’s shooting direction, image and focus. 2 Turn on the camera . Monitor terminal 75 terminal Monitor . 1
Краткое содержание страницы № 18
Adjustment Adjusting Image (Continued) 3 Adjust the shooting direction of the camera Adjust the camera for pan, tilt and rotation, and face the camera towards the subject. Pan: 175 Tilt fastening screw Rotation: 100 Tilt: 80 Shooting direction mark Pan center mark Rotation center mark Rotation knob ( 2) . v Rotate both pan 5175 7 and rotation 5100 7 from the positions Memo aligned with the camera’s shooting direction mark, pan center mark and rotation center mark. Be sure to hold
Краткое содержание страницы № 19
Adjustment 4 Adjust the image size Loosen the fastening screw for the zoom adjustment ring and move the ring to the left/right to adjust the image size. After adjustment is complete, fasten the screw with pressing it slightly toward the lens direction (toward the shooting direction). 5 Adjust the focus ① Hold the focus adjust gear knob, shift the catch from point A to point B as illustrated in the diagram to disengage the gear. To prevent the gear shaft from breaking when the gear is opened too
Краткое содержание страницы № 20
Adjustment Adjusting Image (Continued) 6 Fine adjust the focus ① Press and hold the [ J] button. v Focus adjust mode will be activated and "FOCUS ADJUST MODE" is displayed on the monitor screen. v The contours are emphasized as the iris opens and the depth of field becomes shallow. v After adjustment, press [ K, H, I], [SET] or [MENU] to exit focus adjust mode. The mode is also automatically deactivated after about 30 seconds. During the focus adjust mode, the electronic shutter will function Me
