Руководство по эксплуатации Elmo TEB4404

Краткое содержание страницы № 1

TEB4404
INSTRUCTION MANUAL
INFORMATION
CAUTION
RISK OF ELECTRIC SHOCK
This equipment has been tested and
DO NOT OPEN
found to comply with the limits for Class A
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK).
digital device, pursuant to Part 15 of the
NO USER SERVICEABLE PARTS INSIDE.
FCC Rules. These limits are designed to
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
provide reasonable protection against
The lightning flash with arrowhead symbol, with

Краткое содержание страницы № 2

IMPORTANT SAFEGUARDS 1. Read Instructions 12. Lightning All the Safety and operating instructions should be For added protection for this video product during a read before the appliance is operated. lightning storm, or when it is left unattended and 2. Retain Instructions unused for long periods of time, unplug it from the The safety instructions and instruction manual wall outlet and disconnect the power supply and should be retained for future reference. cable system. This will prevent damag

Краткое содержание страницы № 3

PART NAMES AND FUNCTIONS All dimensions in mm (inch) 4 3 1 60 (2.4) 8 5 90 (3.5) 2 7 6 1 Lens mount + DC12V Mount a CS-mount lens. - 2 Camera mount For mounting a camera on wall, housing, etc. + + (1/4"-20UNC thread) AC24V 3 Focusing dial For fine-adjustment of the lens back-focus. 4 IRIS terminal 1 2 Connect when an automatic iris lens is used. + - 5 VIDEO OUT terminal 7 Ground terminal Connect to a monitor TV, etc. Connect this to the ground wire of the (BNC connector) power supply cord. 6 AC

Краткое содержание страницы № 4

HOW TO USE 1. Adjust the iris and focus of the lens so that optimum image CS-mount may be obtained. * Usable lenses Lens 4mm or less CS-mount lenses, whose length "L" (in the illustration) L from the bearing surface of the mount is 4mm or less if protruded, should be used. * Using the zoom lens (adjustment of the back focus) The camera is set at the standard back focus position when Lens Camera shipped from factory. Depending on types of zoom lenses, however, slight readjustment may be necessary

Краткое содержание страницы № 5

CAMERA CONTROLS 1 2 3 4 8 6 7 5 1 AGC switch In case of necessity, set the AGC switch to OFF position. 2 GAMMA selector ( ) Gamma can be selected. ON : 1 OFF : 0.45 3 INT/LL switch • INT. (internal) control Monitor TV switch When the internal CAMERA synchronization is used, set the switch to the INT To DC 12V power supply side. To AC 24V power supply Monitor TV • L.L. (Line-lock) control Video output switch CAMERA 1 Video Matching the vertical input Video switcher synchronization with Video outp

Краткое содержание страницы № 6

turned on. This is necessary to stabilize the camera against the power noise. 4 BLC (Black Light Control) switch With the AGC switch at ON position, BLC are available. By combining the BLC switches 1 and 2, the following can be adjusted: 1 2 L L Overall area (AREA 1) L H Lower area (AREA 2) H L Central area (AREA 3) H H Lower and central areas (AREA 4) AREA 1 AREA 2 AREA 3 AREA 4 5 IRIS switch When a DC driven type auto iris lens is used, set this switch to DC position. When a video feedback typ

Краткое содержание страницы № 7

SPECIFICATION Model TEB4404 Power source DC12V (DC11V-35V) AC24V (AC15V-27V) 60Hz 0.5Hz Power consumption Approx.3.2W Approx.3.0W Pick-up device 1/3"Black & White interline-transfer CCD Effective picture element 768 (H) x 494 (V) Scanning area 4.88mm (H) x 3.66mm (V) Scanning system 2:1 interlaced Scanning frequency (H) (V) 15.734kHz 60Hz Sync. system Internal Line-lock/Internal Resolution 570 TV lines (Horizontal) 350 TV lines (Vertical) Recommended illumination 10 lx (F1.2 under incandesce

Краткое содержание страницы № 8

PRECAUTIONS FOR USE AND INSTALLATION * Never aim the camera at the sun. *Install your camera where no video noise Never aim or point the camera at the sun even appears. if you are not shooting. When camera cables have been laid near * Do not shoot intense light. electric wires or television receivers, a noise Strong light such as a spot light on the image may interfere the image. plane will cause blooming or smear. When If noise occurs, relocate cables or reinstall strong light comes into the im