Краткое содержание страницы № 1
Operating Instructions and Parts Manual
Powered Stock Feeder for Table Saws
Model PF3-EZ
WMH TOOL GROUP, Inc.
2420 Vantage Drive
Elgin, Illinois 60123 Part No. M-1790814
Ph.: 800-274-6848 Revision B 3/08
www.powermatic.com Copyright © 2008 WMH Tool Group
Краткое содержание страницы № 2
Warranty and Service WMH Tool Group, Inc., warrants every product it sells. If one of our tools needs service or repair, one of our Authorized Service Centers located throughout the United States can give you quick service. In most cases, any of these WMH Tool Group Authorized Service Centers can authorize warranty repair, assist you in obtaining parts, or perform routine maintenance and ® major repair on your POWERMATIC tools. For the name of an Authorized Service Center in your area call 1
Краткое содержание страницы № 3
Table of Contents Warranty and Service ..............................................................................................................................2 Table of Contents ....................................................................................................................................3 Warning...................................................................................................................................................4 Introduction ......
Краткое содержание страницы № 4
Warning 1. Read and understand the entire owners manual before attempting assembly or operation. 2. Read and understand the warnings posted on the machine and in this manual. Failure to comply with all of these warnings may cause serious injury. 3. Replace the warning labels if they become obscured or removed. 4. This stock feeder is designed and intended for use by properly trained and experienced personnel only. If you are not familiar with the proper and safe operation of a stock feed
Краткое содержание страницы № 5
blahblahblah 21. Make your workshop child proof with padlocks, master switches or by removing starter keys. 22. Give your work undivided attention. Looking around, carrying on a conversation and “horse-play” are careless acts that can result in serious injury. 23. Maintain a balanced stance at all times so that you do not fall or lean against moving parts. Do not overreach or use excessive force to perform any machine operation. 24. Use the right tool at the correct speed and feed rate.
Краткое содержание страницы № 6
Introduction This manual is provided by WMH Tool Group, Inc. covering the safe operation and maintenance procedures for a Model PF3-EZ Stock Feeder. This manual contains instructions on installation, safety precautions, general operating procedures, maintenance instructions and parts breakdown. This machine has been designed and constructed to provide years of trouble free operation if used in accordance with instructions set forth in this manual. If there are any questions or comments, ple
Краткое содержание страницы № 7
Features 7
Краткое содержание страницы № 8
1 Handle with Flat Washer Unpacking 3 Spacers 1 Boring Template Open shipping containers and check for shipping damage. Report any damage 1 Owner's Manual immediately to your distributor and shipping 1 Warranty Card agent. Do not discard any shipping material until Box 2: the Stock Feeder is mounted and running properly. 1 Elevating Column 1 Stand Compare the contents of the containers with the following parts list to make sure all parts are 1 Handwheel intact. Missing parts,
Краткое содержание страницы № 9
Assembly Tools needed for assembly (not provided): Electric drill center punch and hammer 10.5mm drill bit M12 x P1.75 tap 12mm and 19mm wrenches 4mm hex wrench Hardware needed for assembly (not provided): 4 M12 flat washers 4 M12 x P1.75 hex cap screws (length will depend upon thickness of saw table) Exposed metal areas of the Stock Feeder have been factory coated with a protectant. This should be removed with a soft cloth dampened wit
Краткое содержание страницы № 10
6. Tighten the screws firmly with a 19mm wrench. 7. Insert the pin assembly into the hole (Figure 2). You may need to rotate it until it seats properly in the hole. 8. Install a flat washer and cast iron handle (Figure 2) to the threads of the top screw as shown, by screwing the handle down clockwise onto the screw threads. 9. In the area above the pin, remove the hex nut from the screw with a 19mm wrench, but leave the flat washer in place. In place of Figure 2 the hex nut, insta
Краткое содержание страницы № 11
NOTE: The handle can be pivoted out of the way if necessary. Lift up on the handle, rotate the handle on its pin, then release the handle, making sure it fully seats itself on the pin. 16. Mount the stock feeder to the elevating column by sliding the stud of the stock feeder into the hole of the pivot joint (Figure 6). Install the remaining flat washer and handle onto the stud, and tighten the handle. Grounding Instructions Electrical connections must be made by a qualified elect
Краткое содержание страницы № 12
Recommended Gauges (AWG) of Extension Cords Extension Cords Extension Cord Length * If an extension cord is necessary make sure the cord rating is suitable for the amperage listed on 25 50 75 100 150 200 Amps the machine's motor plate. An undersize cord feet feet feet feet feet feet will cause a drop in line voltage resulting in loss < 5 16 16 16 14 12 12 of power and overheating. 5 to 8 16 16 14 12 10 NR The chart in Figure 7 shows the correct size cord to use based on cord length
Краткое содержание страницы № 13
Pivot To pivot the Stock Feeder (for maintenance, oil filling, etc.): 1. Loosen the handle (E, Figure 10) and pull up on the pin (F, Figure 10). 2. Pivot the Stock Feeder into position. (NOTE: At 90 degrees of pivot, as shown in Figure 10, the pin will lock into place.) 3. Re-tighten the handle (E, Figure 10). Figure 10 Operating Controls Switch The control switch is shown in Figure 11. The switch can be set to either Forward or Reverse (the arrows on the switch label refle
Краткое содержание страницы № 14
General Operating Instructions 1. Make sure all locking handles are tight before operating the Stock Feeder. 2. The Stock Feeder should be used in conjunction with a fence on the table saw. 3. The rollers must grip the offcut as well as the part of the workpiece being fed. 4. Position the Stock Feeder so that the axis of the saw blade lines up between the infeed roller and center roller. See Figure 13. This will allow the Stock Feeder to grip the near part of the workpiece as it enter
Краткое содержание страницы № 15
1. Loosen and remove the hex nut and flat washer on the roller shaft with a 24mm wrench. 2. Remove the outer roller. 3. Install a spacer on the shaft and flush against the inner roller as shown in Figure 15. 4. Re-install the outer roller. 5. Install the flat washer and hex nut and tighten with wrench. 6. Repeat for the other rollers if needed. Maintenance Before performing any maintenance on the Stock Feeder, disconnect it from the electrical supply by pulling o
Краткое содержание страницы № 16
Fill the oil reservoir about every 1,000 hours or six months, or sooner if needed. To fill with oil: 1. Pivot the Stock Feeder so that the rollers are facing down. See Figure 19. 2. Unscrew and remove the two socket head cap screws on the back cover with a 5mm hex wrench, and remove the back cover (Figure 19). 3. Unscrew the oil cap (Figure 19) and pour a good quality general purpose oil into the hole. Do not overfill. 4. When finished, install and tighten the oil cap, and instal
Краткое содержание страницы № 17
Troubleshooting Trouble Probable Cause Remedy Not connected to power source. Check plug connection. Feeder will not start. Fuse blown, or circuit breaker tripped. Replace fuse, or reset circuit breaker. Cord damaged. Replace cord. Replace with adequate size and Feed speed is not Extension cord too light or too long. length cord. [page 12] sufficient; machine has low power. Low current from electrical supply. Contact a qualified electrician. Workpiece jams while feeding it beneath
Краткое содержание страницы № 18
Replacement Parts Replacement parts are listed on the following pages. To order parts or reach our service department, call 1-800-274-6848, Monday through Friday (see our website for business hours, www.powermatic.com). Having the Model Number and Serial Number of your machine available when you call will allow us to serve you quickly and accurately. 18
Краткое содержание страницы № 19
Parts List: Stand Assembly Index No. Part No. Description Size Qty 1............... PF3EZ-101 ..............Column Base......................................................................................... 1 2............... PF3EZ-102 ..............Memo-Lock Collar ................................................................................. 1 3............... TS-2360121.............Flat Washer........................................................M12............................ 1 4
Краткое содержание страницы № 20
Index No. Part No. Description Size Qty 58.............PF3EZ-158 ..............Rack ..................................................................................................... 1 59............. TS-1502021.............Socket Head Cap Screw.....................................M5x10........................ 5 60............. PF3EZ-160 ..............Hand Wheel .......................................................................................... 1 61............. PF3EZ-161 .........
