Краткое содержание страницы № 1
MODEL T10460, T10462 &
T10464
PANEL SHAPING JIG
OWNER'S MANUAL
(For models manufactured since 01/12)
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
Краткое содержание страницы № 2
This manual provides critical safety instructions on the proper setup, operation, maintenance, and service of this machine/tool. Save this document, refer to it often, and use it to instruct other operators. Failure to read, understand and follow the instructions in this manual may result in fire or serious personal injury—including amputation, electrocution, or death. The owner of this machine/tool is solely responsible for its safe use. This responsibility includes but is not limited to
Краткое содержание страницы № 3
Table of Contents INTRODUCTION ............................................... 2 SECTION 4: ACCESSORIES ......................... 17 SECTION 5: MAINTENANCE ......................... 18 SECTION 6: SERVICE ................................... 18 SECTION 1: SAFETY ....................................... 5 SECTION 7: PARTS ....................................... 19 SECTION 2: SETUP ......................................... 8
Краткое содержание страницы № 4
INTRODUCTION Manual Accuracy Contact Info your jig may not exactly match the manual Machine Description www.grizzly.com
Краткое содержание страницы № 5
Identification Figure 1. To reduce the risk of serious injury when using this machine, read and understand this entire manual before beginning any operations.
Краткое содержание страницы № 6
Machine Data Sheet Machine Data Sheet MODEL T10460, T10462, T10464 PANEL SHAPING JIG Model Number T10460 T10462 T10464 Product Dimensions Shipping Dimensions Pneumatic Construction
Краткое содержание страницы № 7
SECTION 1: SAFETY For Your Own Safety, Read Instruction Manual Before Operating this Machine The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words intended to convey the level of impor- tance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures. Indica
Краткое содержание страницы № 8
DISCONNECTING POWER SUPPLY. GUARDS & COVERS. NEVER STAND ON MACHINE. APPROVED OPERATION. STABLE MACHINE. DANGEROUS ENVIRONMENTS. AWKWARD POSITIONS. ONLY USE AS INTENDED. UNATTENDED OPERATION. OFF USE RECOMMENDED ACCESSORIES. MAINTAIN WITH CARE.
Краткое содержание страницы № 9
Additional Safety Instructions for Jig OPERATING MACHINERY. FEEDING WORKPIECE. STARTING MACHINE. SHOP SAFETY. DEPTH OF CUT. KICKBACK. SHAPING CONTOURED WORK. HAND POSITIONING. BLIND CUT WHEN POSSIBLE. SAFETY GUARDS.
Краткое содержание страницы № 10
SECTION 2: SETUP Unpacking This jig presents seri- ous injury hazards to untrained users. Read through this entire man- ual to become familiar please call us immediately at with the controls and (570)546-9663. operations before using the jig! Otherwise, filing a freight claim can be difficult. Wear safety glasses dur- ing the entire setup pro- cess! SUFFOCATION HAZARD! Keep children and pets away This jig and
Краткое содержание страницы № 11
Box 1: (Figures 2) Qty Site Considerations A. B. C. " D. " Shaper Table Size E. F. G. H. I. J. Placement Location K. L. M. N. O. Figure 3 Figure 3. Figure 2. Children and visitors may be seriously injured if unsu- If you cannot find an item on this list, pervised around machinery. carefully check the jig and the
Краткое содержание страницы № 12
Attaching Guards Test Run Figure 4 Troubleshooting Page 20 To verify the jig runs correctly: 1. Figure 4. 2. 3. ON Air Connection 4. Figure 5 5. 6. In-Line Quick-Disconnect Air Piping Oiler Fittings Filter Male Female Regulator (Optional) Your Tool Filter Water Lead-In Automatic Separator
Краткое содержание страницы № 13
SECTION 3: OPERATIONS To complete a typical operation, the Operation Overview operator does the following: 1. 2. 3. not 4. 5. OFF 6. 7. To reduce the risk of 8. serious injury when using this jig, read and understand this entire manual before operating. 9. 10. OFF Damage to your eyes and lungs could result from using this jig without proper protective gear. Always wear safety glasses and a
Краткое содержание страницы № 14
Workpiece Basic Controls Inspection ON/OFF Control Valve Figure 6 ON Before shaping, inspect all workpieces OFF for the following: Material Type: Foreign Objects: Figure 6. Large/Loose Knots: Clamping Switches both Wet or "Green" Stock: Excessive Wa
Краткое содержание страницы № 15
Adjusting Airflow Adjustments Figure 8 Adjusting Clamp Height To adjust the cylinder bracket height: 1. Figure 9 Figure 8. Figure 9. 2. Important: The cylinder bracket must be fas- tened with the (6) M6-1 x 20 cap screws to operate safely. 3.
Краткое содержание страницы № 16
Positioning Workpiece Template Mounting Bracket Figure 12 Figure 10 Figure 12. Installing Templates Figure 10. To install the rear fence: Figure 13 1. 2. 3. Figure 11 Figure 13. Figure 11. Note: To install the coping fences simply reverse the above steps.
Краткое содержание страницы № 17
Miter Bar Rub Collar Figure 16 Figure 14. Figure 16. Figure 14. Clamping Workpiece ON. Figure 17 Always ensure that the jig base will clear the cutterhead or kickback could occur, caus- ing personal injury or property damage. Vertical Fence Figure 15 Figure 17. Figure 15.
Краткое содержание страницы № 18
Tip: To prevent tear-out in the workpiece Using Jig shape end grain first. Wood is less likely to tear while edge-shaping, so any tearout from end grain shaping can be removed. Use a sacrificial backing block between the workpiece and the coping fence as needed to further reduce tearout (see Figure 19). Tip: Use a practice piece similar to the workpiece in order to test the results before shaping the w
Краткое содержание страницы № 19
SECTION 4: ACCESSORIES 1 T23115— ⁄2" X 50' Hose Reel Some aftermarket accessories can be installed on this machine that could cause it to function improperly, increasing the risk of serious personal injury. To minimize this risk, only install accessories recommended for this machine by Grizzly. NOTICE Refer to the newest copy of the Grizzly Catalog for other accessories available for this machine. Figure 23. H7274—Pressure Regulator T10461—T10460 Arched Door Templates T10463—T10462
Краткое содержание страницы № 20
SECTION 5: MAINTENANCE Cleaning Always disconnect air to the jig before performing maintenance. Failure to do this may result in seri- ous personal injury. Schedule Lubrication Daily Check Weekly Maintenance SECTION 6: SERVICE Note: Please gather the serial number and manufacture date of your jig before calling. Troubleshooting
