Краткое содержание страницы № 1
MODEL G0605X1/G0606X1/
G0696X/G0697X
12" LEFT TILTING TABLE SAW
OWNER'S MANUAL
Model G0697X
Model G0606X1
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
Краткое содержание страницы № 2
This manual provides critical safety instructions on the proper setup, operation, maintenance, and service of this machine/tool. Save this document, refer to it often, and use it to instruct other operators. Failure to read, understand and follow the instructions in this manual may result in fire or serious personal injury—including amputation, electrocution, or death. The owner of this machine/tool is solely responsible for its safe use. This responsibility includes but is not limited to
Краткое содержание страницы № 3
Table of Contents INTRODUCTION ............................................... 2 SECTION 5: SHOP MADE SAFETY ACCESSORIES .............................................. 50 SECTION 1: SAFETY ....................................... 5 SECTION 6: AFTERMARKET ACCESSORIES FROM GRIZZLY ............................................. 58 SECTION 7: MAINTENANCE ......................... 60 SECTION 2: POWER SUPPLY ..............
Краткое содержание страницы № 4
INTRODUCTION Manual Accuracy Contact Info your machine may not exactly match the manual Machine Description www.grizzly.com
Краткое содержание страницы № 5
Identification Figure 1. To reduce the risk of For Your Own Safety Read Instruction serious injury when using Manual Before Operating Saw this machine, read and a) Wear eye protection. understand this entire b) Use saw-blade guard and spreader for manual before beginning every operation for which it can be used, any operations. including all through sawing. c) Keep hands out of the line of saw blade. d) Use a push-stick when required. e
Краткое содержание страницы № 6
MODEL G0605X1/G0606X1/G0696X/G0697X 12" LEFT-TILTING TABLE SAWS G0605X1 G0606X1 G0696X G0697X Model Number Motor Required Power Supply Circuit Speed Power Requirement Full Load Current Rating Plug/Outlet Type (Recommended) Table Size (full assembly) Table Height Above Floor Overall Machine Size Footprint Size Weight
Краткое содержание страницы № 7
SECTION 1: SAFETY For Your Own Safety, Read Instruction Manual Before Operating this Machine The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words intended to convey the level of impor- tance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures. Indica
Краткое содержание страницы № 8
DISCONNECTING POWER SUPPLY. FORCING MACHINERY. GUARDS & COVERS. APPROVED OPERATION. NEVER STAND ON MACHINE. STABLE MACHINE. DANGEROUS ENVIRONMENTS. AWKWARD POSITIONS. ONLY USE AS INTENDED. USE RECOMMENDED ACCESSORIES. UNATTENDED OPERATION.
Краткое содержание страницы № 9
Additional Safety for Table Saws HAND POSITIONING. FENCE. PUSH STICKS/BLOCKS. BLADE GUARD. CUT-OFF PIECES. OFF BLADE ADJUSTMENTS. RIVING KNIFE. OFF CHANGING BLADES.
Краткое содержание страницы № 10
Preventing Kickback Take the precautions below to avoid the most common causes of kickback: Statistics show that most common acci- dents among table saw users can be linked to kickback. Kickback is typically defined as the high-speed expulsion of stock from the table saw toward its opera- tor. In addition to the danger of the opera- tor or others in the area being struck
Краткое содержание страницы № 11
Glossary of Terms VERY ARBOR: PARALLEL: BEVEL EDGE CUT: PERPENDICULAR: Page 42 BLADE GUARD ASSEMBLY: PUSH STICK: Page 35 Page 53 RABBET: CROSSCUT: Page 45 Page 41 RIP CUT: DADO BLADE: Page 40 RIVING KNIFE: DADO CUT: Page 38 Page 42 SPREADER: FEATHERBOARD: Page 50 STRAIGHTEDGE: KERF: THIN KERF BLADE: KICKBA
Краткое содержание страницы № 12
SECTION 2: POWER SUPPLY Availability Circuit Information For your own safety and protection of property, consult a qualified electrician if Electrocution, fire, or you are unsure about wiring practices or equipment damage may electrical codes in your area. occur if machine is not correctly grounded and Note: The circuit requirements listed in this man- connected to the power ua
Краткое содержание страницы № 13
Model G0606X1/G0697X Model G0606X1/G0697X Circuit Requirements for 440V Connection Device For 220V operation: Voltage Conversion Nominal Voltage .............................. 440V/480V Cycle ..........................................................60 Hz Phase .................................................... 3-Phase Circuit Rating ...................................... 15 Amps Connection ......Hardwire with Locking Switch GROUNDED
Краткое содержание страницы № 14
Grounding Instructions Correcting Phase Polarity To correct wiring that is out of phase: 1. Extension Cords (220V Only) 2. Figure 5. Minimum Gauge Size ...........................12 AWG Maximum Length (Shor
Краткое содержание страницы № 15
4. Figure 7 Voltage Conversion NOTICE Figure 7. Refer to the motor junction box cover dia- gram for motor connection locations and 5. voltage conversion. If not present, use the instructions below, or call our Tech Support Figure 8 Department at (570) 546-9663. Page 80 Page 82 Converting Model G0606X1/G0697X to 440V 1. 2. Figure 6 Figure 8. 6. Figure 9
Краткое содержание страницы № 16
SECTION 3: SETUP Needed for Setup This machine presents serious injury hazards to untrained users. Read through this entire manu- al to become familiar with Description Qty the controls and opera- tions before starting the machine! Wear safety glasses dur- ing the entire setup pro- cess! This machine and its com- ponents are very heavy. Get lifting help or use power lifting equipment such as a forklift to move heavy i
Краткое содержание страницы № 17
Hardware Recognition Chart
Краткое содержание страницы № 18
G0605X1/G0606X1 NOTICE If you cannot find an item on this list, check Inventory the mounting location on the machine or the packaging materials. Sometimes parts are pre-installed for shipping, or they become hidden by packaging materials. Fence Inventory Box Contents (Figure 12) Qty A. B. Table Saw Unit Box Contents (Figure 10 & 11) Qty A. B. C. D. E. Figure 12. F. G. Fence Rail Inventory H. Box Contents (Fig
Краткое содержание страницы № 19
Extension Table Inventory Outfeed Table Inventory Box Contents (Figure 14) Qty Box Contents (Figure 15) Qty A. A. B. B. C. C. D. D. E. E. Hardware and Tools (Not Shown): Qty Hardware and Tools (Not Shown): Qty
Краткое содержание страницы № 20
Fence Box Contents (Figure 19) Qty A. B. Figure 16. Figure 19. Fence Rail Inventory Box Contents (Figure 20) Qty A. B. C. Figure 17. Figure 18. Figure 20. Hardware and Tools (Not Shown): Qty Hardware and Tools (Not Shown): Qty
