Краткое содержание страницы № 1
INSTRUCTION MANUAL
405mm Variable
Speed Scroll Saw
with Laser Line Generator*
• Melbourne • Perth • Auckland • Hong Kong • Shanghai
LSSCR
• Taipei • New York • Verona • London • Paris
041222 ED4 PS
1
Краткое содержание страницы № 2
Contents Introduction 3 Full 2 Years Home Use Warranty Environmental protection 3 Whilst every effort is made to ensure your complete Description of symbols 3 satisfaction with this tool, occasionally, due to the mass Specifications 3 manufacturing techniques, a tool may not live up to our Safety rules for laser lights 4 required level of performance and you may need the General safety instructions 4 assistance of our service department. Additional safety rules for scroll saws 5 Acces
Краткое содержание страницы № 3
Symbols Dear Customer The rating plate on your tool may show symbols. These If you require any help with your product, whether it represent important information about the product or is a Warranty claim, spare part or user information, instructions on its use. please phone our Help Line for an immediate response. Phone 1300 880 001 in Australia or 0800 445 721 in Wear hearing protection. New Zealand. Wear eye protection. Wear breathing protection. Introduction Conforms to relevant Your n
Краткое содержание страницы № 4
Safety rules for laser lights General safety instructions The laser light/laser radiation used in the GMC REDEYE® To use this tool properly, you must observe the safety system is Class 1 with maximum 1mW and 650nm regulations, the assembly instructions and the operating wavelengths. These lasers do not normally present an instructions to be found in this Manual. All persons who optical hazard, although staring at the beam may cause use and service the machine have to be acquainted with flash
Краткое содержание страницы № 5
7. Dress correctly. Do not wear loose clothing or intended for outdoor use and are so marked. jewellery. They can be caught in moving parts. Rubber 17. Stay alert. Watch what you are doing. Use common gloves and non-slip footwear are recommended when sense. Do not operate a power tool when you are working outdoors. If you have long hair, wear a tired. protective hair covering. 18. Check for damaged parts. Before using a tool, 8. Use safety accessories. Safety glasses and earmuffs chec
Краткое содержание страницы № 6
• T his scroll saw is intended for indoor use only. supply before leaving the work area. • T o avoid being pulled into the blade, do not wear loose • D o not perform layout, assembly or setup work on the fitting gloves, loose clothing, neck ties or jewellery. Tie table while the cutting tool is operating. back long hair and roll long sleeves above elbows. • T urn saw off and remove plug from power supply outlet • D o not cut pieces too small to hold by hand. When before installing or removing
Краткое содержание страницы № 7
1. On/off switch / variable speed dial 10. Table Know your product 2. Laser light on/off switch 11. Table insert Before using the tool, familiarise yourself with all the operating features and 3. LED light on/off switch 12. Blade tension lever safety requirements. 4. Laser aperture 13. Blade adapters Use the tool and accessories only for 5. Laser line alignment knob 14. Blade adapter knobs the applications intended. All other 6. Sawdust blower tube 15. Blade applications are expressly ruled
Краткое содержание страницы № 8
7. M ost blade packages state the size or thickness of Mounting the saw to a workbench wood which that blade is intended to cut, and the It is recommended that the scroll saw is secured to a work radius (size of curve) which can be cut with that blade. bench to gain maximum stability and prevent noise and 8. W ider blades cannot cut curves as tight or small as vibration. thinner blades. 1. Using the base of the scroll saw as a template mark 9. This saw uses 127mm long pin type and flat b
Краткое содержание страницы № 9
when lowered, lift the blade tension lever back up Installing blades and turn it in an anti-clockwise direction to loosen Caution. Always ensure that the saw is switched off and the blade tension. unplugged from the mains supply before removing or 9. If the tension is too loose when lowered, lift the blade tension lever back up and turn it in a clockwise installing a blade. direction to tighten the blade tension. 1. Lift up the blade tension 10. Replace the table insert. lever (12) to
Краткое содержание страницы № 10
Aligning the degree scale pointer Turning on and off 1. Loosen the table lock knob (17) and position the 1. To turn on the scroll saw table so that it is at a right angle to the blade. lift the on/off switch (1). 2. T o turn off the scroll saw push the on/off switch (1) down. Adjusting the sawdust blower Your scroll saw features a sawdust blower (6) to help keep the work area clean for more accurate scroll cuts. For best results always direct air flow from the blower tube at the blad
Краткое содержание страницы № 11
Adjusting the laser line 1. To adjust the laser beam first turn on the scroll saw using the on/off switch (1) the speed. 3. Determine the optimum speed by making a trial cut in a scrap piece of material. Note. Using the correct speed for the job increases the 2. To adjust the laser line turn the laser line alignment life of the saw blade. knob (5) in an anti-clockwise direction to loosen it and then move it to the left or right until the Selecting the correct speed laser line is in line
Краткое содержание страницы № 12
5. The saw will not cut wood by itself, you allow the Locking the scroll saw saw to cut wood by guiding the wood into the blade The on/off switch features a as it moves. locking peg that can be used 6. T he drop foot (8) should always be lowered until it to help prevent unauthorised just rests on top of the work piece to prevent your use. work piece from lifting during operation but not so 1. S lide a padlock through the much that the workpiece drags. To lower or raise the locking peg
Краткое содержание страницы № 13
Maintenance Cleaning Warning. Always ensure that the tool is switched off 1. K eep the tool’s air vents unclogged and clean at all and the plug is removed from the power point before times. making and adjustments or maintenance procedures. 2. Remove dust and dirt regularly. Cleaning is best done An occasional coat of paste wax on the work table will with a brush or a rag. allow the wood being cut to glide smoothly across the 3. Re-lubricate all moving parts at regular intervals. work surfac
Краткое содержание страницы № 14
14
Краткое содержание страницы № 15
15
Краткое содержание страницы № 16
Carefully read the entire Instruction Manual before using this product. With continuing product development changes may Before returning this product for a have occurred which render the product received Warranty Claim or any other reason slightly different to that shown in this instruction Please Call 1300 880 001 (Australia) manual. The manufacturer reserves the right to or 0800 445 721 (New Zealand) change specifications without notice. Note: Specifications may differ from country to
