Краткое содержание страницы № 1
®
RV DIGITAL SATELLITE SYSTEM
with Digital Elevation Sensor
Model RM-DM46
may also be packaged as
RM-DM00, RMDM04, RMFLDM4
U.S. Patent Number 5,532,710
Made in U.S.A.
Winegard Company • 3000 Kirkwood St. • Burlington, IA 52601-2000
319/754-0600 • FAX 319/754-0787 • www. winegard.com
Printed in U.S.A. © Winegard Company 2002, 2005 2451069 Rev. 12/05
1
Краткое содержание страницы № 2
Operation STEP 1. The more accurately you determine North, the easier it is to locate the satellite. Step outside and away from your vehicle. (Standing to near your vehicle can give incorrect compass readings.) It is helpful if there is a landmark on the horizon to represent North. Return to the vehicle and point the Directional Dial North, or to the landmark. DIRECTIONAL ELEVATIING CRANK HANDLE DIRECTIONAL DIAL DIRECTIONAL HANDLE POIINTER FIGURE 1 RED SCREW ROTATION CLAMP STEP 2. Turn on receiv
Краткое содержание страницы № 3
Tuning Antenna STEP 1. Your receiver should indicate it is receiving a signal. To tune your antenna for the best signal strength. SLOWLY move the antenna left, then right, until you have found the position that gives the highest signal strength. It is important to turn the antenna slowly. Because the signal is digital, the receiver takes a few seconds to lock on. STEP 2. Place rotation clamp in the LOCK position. This prevents an tenna movement and loss of signal. STEP 3. SLOWLY raise, then lowe
Краткое содержание страницы № 4
Signal from satellite Trouble Shooting 1. You may need to roatate the dish in small increments to find the signal. Rotate the dish 3° at a time to the left, stopping for a few seconds each Antenna Reflector at 90° time you move the dish. Try moving the dish up to 20° to the left. If no signal is found, return to the azimuth listed and and try rotating 20° to the right. This will help correct for any errors in setting the directional handle. 2. Be sure you have a clear line of sight. The signal f
Краткое содержание страницы № 5
Center Roof Line Assembly & Installation Things you need — Screwdrivers (Phillips and slot) Non-hardening sealant ABS glue 1-3/4” hole saw (Check manufacturer’s specifications for Drill with 1/8” bit 7/16” wrench compatibility with your roof material.) Tape measure Winegard’s Digital Elevation Sensor has been INSTALLED and CALIBRATED at the factory STEP 1. Choose a location on the roof for dish that will allow dish to raise and rotate without interfering with other roof-mounted equipment. Make s
Краткое содержание страницы № 6
STEP 3. Attach dish to backup. Use bolts and (4) Antenna nuts provided, Figure 4. Mounting Bolts STEP 4. Mount dish on roof in upright position. Rotate clockwise to stop, Figure 5. Dish will be toward back of vehicle when in stowed or travel position. The word FRONT is embossed on the base and should face the front of vehicle. Secure to roof using screws (provided). The travel bracket sjhould be mounted to roof 6-1/8” from base of dish, toward back of vehicle. See Figure 6. NOTE: Apply non-harde
Краткое содержание страницы № 7
DIGITAL ELEVATION SENSOR ROOF CONNECTIONS The illustrations below show the different methods of connecting wires at roof level; method will depend on model. Wire colors MUST MATCH, ie. red to red, green to green, black to black. This wire harness connects to the digital Supplied with DM-2000 only elevation sensor on the antenna 3M UR TERMINAL Squeeze pliers until DO NOT STRIP red plunger is flush wires, terminal is with res of terminal. Snap self-stripping. (Pliers not supplied.) Slide wires all
Краткое содержание страницы № 8
FIGURE 12 STEP 15. The directional handle and threaded rod Plastic will fit roofs up to 5-1/4” thick. If you are using Plug wedges to compensate for roof/cceiling slope, be sure to allow for this extra thickness. You may add an extension to the directional handle for thicker Spacer roofs. Each extension will increase the length of the Spring directional handle by 2-1/4”. Figure 11 FIGURE 11 WITH ROOF WEDGE Measure from top of roof wedge to ceiling. TOP OF ROOF WEDGE Worm Gear Threaded Rod CEILIN
Краткое содержание страницы № 9
CAUTION! FIGURE 15 After INITIAL INSTALLATION, the antenna SHOULD ROTATE APPROXIMATELY 360° FROM TRAVEL POSITION. The pointer on the DIRECTIONAL HANDLE should point towards the RED Elevating Shaft SCREW ON THE ROTATION CLAMP when in the TRAVEL POSITION. FIGURE 14 Threaded Tube Directional Handle Extension Ceiling Plate Pointer must (4) #10 Phillips Flat Head Screws point to RED Rotation SCREW at Clamp Directional CENTER OF Handle Red Screw ROTATION ALIGN POINTER CLAMP when in WITH ANTENNA TRAVEL
Краткое содержание страницы № 10
Digital Elevation Sensor Interior Wallplate STEP 19. See Figure 17. If using the SM-1000 surface FIGURE 17 mount box, feed cable through hole in box. STEP 20. Connect wires coming from sensor on roof to wall plate display in vehicle. It is important Cable and plug from to properly connect the wires at the roof and roof sensor unit; the wall plate. (Plug will click when plugs into sensor inserted properly.) The system is designed to use a 9 volt battery OR +12 VDC from vehicle. Do not use both! I
Краткое содержание страницы № 11
Parts List 11
Краткое содержание страницы № 12
Parts List 12
Краткое содержание страницы № 13
Parts Views Rev/6/11/01 13
Краткое содержание страницы № 14
Notes 14
Краткое содержание страницы № 15
Notes 15
Краткое содержание страницы № 16
Specifications ANTENNA & MOUNT Height when raised 30" verticle max. Height in the travel position 8" max. Operating radius17" (34" diameter circle) Roof space required 26" ® TM LNB Compatible with DIRECTV , DISH Network , and ExpressVu (northern U.S. and Canada) Weight 12 lbs. Color Cool gray Antenna height 20.9" Antenna width 19.2" F/D 0.59 o Offset angle 24 Frequency range 10.95 - 12.75 GHz Gain: 11.2 GHz 33.22 dBi 12.1 GHz 33.89 dBi 12.6 GHz 34.23 dBi Aperture efficiency 73% Cross polarizati
Краткое содержание страницы № 17
TEMPLATE ON NEXT PAGE 17
Краткое содержание страницы № 18
ALIGN BASEP AREA M “FRO POINT TO OF VEH 1-3/4” DIA. DRILL COMPLETELY THROUGH CEILING TempRM 18
Краткое содержание страницы № 19
Roof Template WITH PLATE MARKED ONT” O FRONT HICLE 1/8” DRILL BIT 8 HOLES. DO NOT DRILL THROUGH CEILING. 19
