Краткое содержание страницы № 1
Owner's Manual
ROUTER
Double Insulated
Model No.
315.175000
Save this manual for
future reference
• Safety
• Features
_, CAUTION: Read and
follow all Safety Rules and • Adjustments
Operating Instructionsbefore
• Operation
first use of this product.
• Maintenance
• Parts List
Sears, Roebuck and Co., Hoffman Estates, IL 60179 USA
Visit the Craftsman web page: www.sears.com/craftsman
®
972000-673
7-99
Краткое содержание страницы № 2
I Table Of Contents .......................................................................................................................................... 2 • Warranty ......................................................................................................................................................... 2 • Introduction ..................................................................................................................................................... 2 • Rul
Краткое содержание страницы № 3
The purpose of safety symbols Is to attract your attention to possible dangers. The safety symbols, and the explanations with them, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger. The Instructions or warnings they give are not substitutes for proper accident prevention measures. SYMBOL MEANING SAFETY ALERTSYMBOL: Indicatesdange_waming, orca_ion. M_ used inco_un_onwitho_ersym_lsorpict_raphs. DANGER: Failure to obey a safety warning
Краткое содержание страницы № 4
I PROTECT YOUR HEARING, Wear hearing Repair Center. Stay constantly aware of cord location. protection during extended periods of operation, • INSPECT EXTENSION CORDS I DO NOT ABUSE CORD. Never carry tool by cord or yank it to disconnect from receptacle. Keep cord PERIODICALLY and replace if damaged. from heat, oil, and sharp edges. • KEEP HANDLES DRY, CLEAN, AND FREE • SECURE WORK. Use clamps or a vise to hold FROM OIL AND GREASE. Always use a clean work. It is safer than using your hand and it
Краткое содержание страницы № 5
Depth of cut O - 1-1/2 in. Amperes 8 Collet 1/4 in. No load speed 25,000 RPM Horsepower 1-1/2 Power cord 10 ft. Rating 120 volts, 60 Hz, AC only Net weight 8.13 Ibs. Your router has been shipped completely assembled. ,_k WARNING: If any parts are missing, do not Inspect it carefully to make sure no breakage or operate this tool until the missing parts are damage has occurred during shipping. If any parts are replaced. Failure to do so could result in possible damaged or missing, contact your nea
Краткое содержание страницы № 6
squeeze the tabs on each end and pull outward. To KNOW YOUR ROUTER replace, squeeze the tabs at each end, fit into See Figure I. opening, then release. For your protection, do not Beforeattemptingto use any tool,familiarize yourself use router without chip shield properly In place. withall operatingfeatures and safetyrequirements. WRENCH STORAGE AREA SWITCH Your router has a wrench storage area located on the To turn your router on, depress the switch trigger. top end cap portion of the motor ho
Краткое содержание страницы № 7
CU'I'FER WARNING:Yourrouter shouldneverbe n COLLET connected to power supply when you are WRENCH NUT assembling parts, making adjustments, installing or removing cutters, cleaning, or when not in use. Disconnecting router will prevent accidental starting that could cause serious personal injury. INSTALLING/REMOVING CUTTERS TO LOOSEN m See Figures 2 and 3. • Unplug your router. _h, WARNING: Failure to unplug your router could result in accidental starting causing serious injury. • A spindle lock
Краткое содержание страницы № 8
DEPTH OF CUT ADJUSTMENTS See Figures 4, 5, and 6. We recommend that cuts be made at a depth not exceeding 1/8 in. and that several passes be made to reach depths of cut greater than 1/8 in. • Unplug your router. _k WARNING: Failure to unplug your router could result in accidental starting causing serious injury. • Place your router on a flat surface, loosen locking knob, and turn depth adjusting ring until cutter is inside subbase. See Figure 4. TO TIGHTEN CUTTERATZERO LOCKING DEPTHOF CUT Fig. 5
Краткое содержание страницы № 9
DEPTH OF CUT ADJUSTMENTS WHEN HELPFUL HINTS ROUTER IS MOUNTED TO A ROUTER TABLE J' Always clamp workpiece securely before routing. See Figure 7. ,/ A safe operator is one who thinks ahead. The depth of cut is readable from both sides of the depth ,/ Always wear eye protection when routing. indicator ring. The bottom ring is convenient when using ,/ Make setup adjustments carefully. Then double your router mounted upside down to a routertable. The check. Measure twice and cut once. indicatorpoint
Краткое содержание страницы № 10
FREEHANDROUTING WARNING: Do not use large router bits for & freehand routing. Use of large router bits when See Figure 9. freehand routing could cause loss of control or create other hazardous conditions that could cause possible serious personal injury. When using a router table, large router bits should be used for edging only. Do not use router bits that are larger in diameter than the opening in router base for any purpose. RATE OF FEED IMPORTANT: The whole Usecret" of professional routing a
Краткое содержание страницы № 11
In addition, it is more difficult to control a router when the bit is scraping instead of cutting. With practically no load on the motor the bit will be revolving at close to top RPM, and will have a much greater than normal tendency to bounce off the sides of the cut (especially if the wood has a pronounced grain with hard and soft areas). As a result, the cut produced may have rippled, instead of straight sides. See Figure 10. TOO FAST _oo-slow feeding" can also cause your router to take off i
Краткое содержание страницы № 12
ROUTING Tomakedeeper cutsit istherefore necessary to makeasmanysuccessive passesasrequired, Whenever you are muting a groove, your travel lowering thebit118 inchfor each new pass. In order to should be in a dir ction that places whatever guide save time, do all the cutting necessary at one depth you are using at the right-hand side. In short, when setting, before lowering the bit for the next pass. This the guide is positioned as shown in the first part of will also assure a uniform depth when t
Краткое содержание страницы № 13
STARTING AND ENDING A CUT Whenever the workpieco thickness together with the desired depth of cut (as adjusted by router depth INTERNAL ROUTING setting) are such that only the top part of the edge is Tilt router and place on workpiece, letting edge of to be shaped (leaving at least a 1/16 inch thick uncut subbase contact workpiece first. Be careful not to let portion at bottom), the pilot can ride against the uncut router bit contact workpiece. Turn router on and let portion, which will serve to
Краткое содержание страницы № 14
LUBRICATION _i WARNING: When servicing, use only identical Craftsman replacement parts. Use of any other All of the bearings in this tool are lubricated with a part may create a hazard or cause product sufficient amount of high grade lubricant for the life of damage. the unit under normal operating conditions. Therefore, no further lubrication is required. GENERAL EXTENSION CORDS Only the parts shown on parts list, page 17, are The use of any extension cord will cause some loss of intended to be
Краткое содержание страницы № 15
SWITCHREPLACEMENT • Make lead connections to new switch. Push each lead as far as possible into proper switch See Figures 15 and 16. receptacle. Pull on leads to check lead connections • Unplug your router. with lead receptacles. • Locate switch in handle end place leads so they WARNING: Failure to unplug your router could won't be pinched or contact screws when handle result in accidental starting causing cover is replaced. serious injury. • Make sure molded bend relief (C) is correctly positio
Краткое содержание страницы № 16
CRAFTSMAN ROUTER - MODEL NUMBER 315.175000, _q SEE NOTE"A" 9 10 11 13 14_ "15 NOTE: "A" - The assembly shown represents an Important part of the Double Insulated System. To avoid the poselblllty of alteretlon or damage to the System, service should be performed by your nearest Sears Repair Center. Contact your nearest Sears Retail Store for Service Center Information. 16
Краткое содержание страницы № 17
CRAFTSMAN ROUTER - MODEL NUMBER 315.175000 I The model number will be found on a plate attached to the motor housing. Always mention the model number in all correspondence regarding your ROUTER or when ordering repair parts. ] SEE BACK PAGE FOR PARTS ORDERING INSTRUCTIONS PARTS LIST Key Part No. Number Description Quan. 1 981575-001 Data Plate .............................................................................................. 1 2 970692-001 Label ......................................
Краткое содержание страницы № 18
In U.S.A. or Canada for in-home major brand repair service: Call 24 hours a day, 7 days a week 1-800-4-MY-HOME" (1-800-469-4663) Pars pedir servicio de reparaci6n a domicilio - 1-800-676-5811 Au Canada pour tout le service ou les pi_ces - 1-800-469 4663 For the repair or replacement parts you need: Call 6 a.m. - 11 p.m. CST, 7 days a week Parts Direct" 1-800-366-PART (1-800-366-7278) Pars ordenar piezas con entrega a domicilio - 1-800-659-7084 For the location of a Sears Service Center in your a
Краткое содержание страницы № 19
BILLING SHEET AND I_RICE INFORMATION FOR: CRAFTSMAN ROUTER MODEL NO. 175000 KEY PART NO. DESCRIPTION BUYER P/C BILLING SELLING O.B U.B BASE ORDER COST COST COST POINT 1 981575-001 DATA PLATE 7 81 .00 ,00 .15 2 970692-001 LABEL 7 81 .00 .00 .15 3 981576-001 LOGO PLATE 7 81 ,00 .00 .31 4 989985-003 COLLET NUT (1/4") 7 81 .00 .00 .30 5 974722-000 Dt_I_I H ADJUSTING 7 S1 .00 .00' 2.17 RING ASSY. INCL. KEY 25 974131-001 DEPTH INDICATOR 7 Sl .00 .00 2.67 RING 623166-006 *SQUARE HEAD BOLT 7 81 .00 .00
Краткое содержание страницы № 20
BILLING SHEET AND PRICE INFORMATION FOR: CRAFTSMAN ROUTER MODEL NO. 175000 KEY PART NO. DESCRIPTION BUYER P/C BILLING SELLING O.B U.B BASE ORDER COST COST COST POINT 989592-002 *SCREW #8-10 X 1-3/8" 7 81 .00 .00 .15 FIL. HD.) 2 970502-007 END CAP 7 81 .00 .00 1.49 3 617834-001 BUMPER 7 81 .00 .00 .15 4 623173-006 WIRE NUT 7 81 ""_.- .00 .00' .15 5 970777-002 CORD ASSEMBLY 7 81 .00 .00 2.71 6 973738-001 LOCK BU'i'FON 7 81 .00 .00 .36 7 612858-001 SLIDE ASSEMBLY 7 81 .00 .00 .36 8 612856-002 SWITC
