Краткое содержание страницы № 1
www.collegehillshonda.com
Accessory Application Publications No.
AII 38216-38957
INSTALLATION
REMOTE ENGINE
2006-2008 CIVIC 4-DOOR
Issue Date
STARTER SYSTEM
INSTRUCTIONS (A/T ONLY)
FEB 2008
PARTS LIST Remote Engine Starter Attachment Kit
P/N 08E92-SNA-100B
Remote Engine Starter Unit Kit
P/N 08E91-E22-100B
Engine starter harness
Transmitter
Control unit
Control unit bracket
Antenna
Relay bracket
Key ring
3 Black relays (4-pin)
Protective tape
Engine starter label
18 Wire ties
Fuse label
Accessor
Краткое содержание страницы № 2
www.collegehillshonda.com 7 Foam cushion tapes TOOLS AND SUPPLIES REQUIRED Phillips screwdriver Long blade flat-tip screwdriver Small flat-tip screwdriver 6 mm Hex wrench Flange nut T25 Torx bit 3 mm and 7 mm Drill bits Clip File Ratchet 10 mm Socket Combination wrench Isopropyl alcohol Shop towel Green relay (5-pin) Tape measure Clip remover Diagonal cutters Felt-tip pen Template Center punch Scissors 2 Pairs of needle nose pliers Rubber mallet HDS (Honda Diagnostic System) Masking tape Safety
Краткое содержание страницы № 3
www.collegehillshonda.com Setting the Control Unit SW : 1 RR Junction Unit SW : 2 Trunk or Tailgate 3. Get the control unit. Using a small flat-tip SW : 3 Smart Entry screwdriver, adjust the switches on the control SW : 4 Horn or Buzzer Answer Back unit to the locations shown. Using a isopropyl SW : 5 Trunk Main SW alcohol on a shop towel, clean the area where the SW : 6 Reserve protective tape will attach. Attach the protective tape to the control unit over the switches. Removing the vehicle pa
Краткое содержание страницы № 4
www.collegehillshonda.com 4. Using the key, unlock the opener. 7. If equipped, remove the driver’s dashboard under cover (turn the knob counterclockwise, and 5. Remove the left front door sill trim (two retaining release two clips and pin). tabs, five clips, and three hooks). 3 HOOKS 5 CLIPS PIN 2 RETAINING TABS DRIVER’S 2 CLIPS DASHBOARD UNDER COVER KNOB FRONT 5202112T 8. Remove the driver’s dashboard lower cover (eight LEFT FRONT clips). DOOR SILL TRIM 5202200T 6. Pull away the weatherstrip, a
Краткое содержание страницы № 5
www.collegehillshonda.com 9. Lower the tilt lever, and pull the steering wheel 11. Remove the column lower cover (two self-tapping toward you. Insert a long blade flat-tip screwdriver screws and one screw). along the guide of the column lower cover, and pry the retaining tab of the column upper cover. 2 RETAINING TABS Push. COLUMN LOWER COVER COLUMN UPPER COVER 2 HOOKS 2 SELF-TAPPING COLUMN SCREWS LOWER SCREW RETAINING 5308530T COVER TAB TILT LEVER GUIDE LONG BLADE 6608050T FLAT-TIP SCREWDRIVER
Краткое содержание страницы № 6
www.collegehillshonda.com 12. If equipped, use a small flat-tip screwdriver to 14. Remove the cap from the left sunvisor (four remove the left and right lens from the map light retaining tabs). console (four retaining tabs for each lens). Remove the two bolts, and then release the map CONNECTOR light console. 4 RETAINING TABS FRONT MAP LIGHT CONSOLE LEFT CAP SUNVISOR TORX 5217030T 4 RETAINING LENS SCREW TABS 15. Remove the left sunvisor (two T25 Torx screws, BOLTS and unplug the vehicle connecto
Краткое содержание страницы № 7
www.collegehillshonda.com 18. Pull away the weatherstrip from the left front pillar Installing the Antenna trim. Remove the left front pillar trim (two clips). 20. Using scissors, cut out the template. TEMPLATE SCISSORS LEFT FRONT 2 CLIPS PILLAR TRIM Cut out. 6D01203T WEATHERSTRIP 5202100T 21. Secure the template to the windshield with the tape by aligning it with the edge of the black 19. Remove the clip from the left front pillar trim, and ceramic paint as shown. install a new clip on the lef
Краткое содержание страницы № 8
www.collegehillshonda.com 22. Using two pairs of needle-nose pliers, bend the 23. Measure the antenna cable as shown. Attach the antenna plate according to the illustration and three foam cushion tapes to the antenna cable in measurement shown. the measurement shown. ANTENNA ANTENNA FOAM CABLE CUSHION TAPE ANTENNA 15 mm 360 mm (0.6 in.) (14 in.) 8 mm (0.3 in.) 30 mm (1.2 in.) 30 mm (1.2 in.) 6D01240T 24. Using isopropyl alcohol on a shop towel, clean the area where the antenna will attach. Allow
Краткое содержание страницы № 9
www.collegehillshonda.com 27. Route the antenna cable under the roof liner 29. Using isopropyl alcohol on a shop towel, clean the towards the driver’s side of vehicle, and down areas where the foam cushion tape will attach. along the vehicle harness. Be careful not to Under the roof liner, secure the antenna cable to crease the roof liner. the roof panel with the two foam cushion tapes (cut one foam cushion tape in half) in the areas shown. ROOF LINER ROOF FOAM CUSHION LINER TAPE (1/2) VEHICLE H
Краткое содержание страницы № 10
www.collegehillshonda.com 31. Secure the antenna cable to the vehicle harness Routing the Engine Starter Harness with a wire tie. Secure the wire tie between the 33. Attach the 3 A fuse labels to the engine starter vehicle harness branching points. harness fuse case, and the 40 A fuse labels to the WIRE TIE fuse block. VEHICLE HARNESS LAYOUT OF RELAYS WHEN VIEWED FROM FRONT 4-PIN RELAY (black) RELAY 5-PIN BLOCK RELAY (green) FUSE 40 A FUSE CLIP CASE LABEL 3 A FUSE ANTENNA LABEL CABLE BRANCHING P
Краткое содержание страницы № 11
www.collegehillshonda.com 35. Route the engine starter harness 7-pin connectors 37. Disconnect the vehicle 8-pin connector on the rear up the steering column and to the ignition switch. of the wiper switch and plug the engine starter Unplug the white vehicle 7-pin connector. Plug the harness 8-pin connector into the vehicle 8-pin white engine starter harness 7-pin connectors into connector. the white vehicle 7-pin connectors. ENGINE STARTER HARNESS VEHICLE 8-PIN 8-PIN CONNECTOR IGNITION CONNECTO
Краткое содержание страницы № 12
www.collegehillshonda.com 39. Wrap the vehicle 7-pin connector with one foam 42. At the right of the steering shaft, locate the sub cushion tape, then place the vehicle 7-pin joint box. Using a small flat-tip screwdriver, unplug connector into the gap of the column. the vehicle 6-pin connector from the sub joint box. Plug the engine starter harness 6-pin connectors into the vehicle 6-pin connector and the subjoint VEHICLE 7-PIN box. CONNECTOR (brown) ENGINE STARTER (Squeeze into VIEWED FROM HARN
Краткое содержание страницы № 13
www.collegehillshonda.com 45. With driver's dashboard under cover: Measure 46. Secure the engine starter harness to the vehicle the indicated dimension on the instrument panel harness using a wire tie. and mark with a felt-tip pen and a center punch. • With driver's dashboard under cover: Secure in the hole you made in the instrument panel. INSTRUMENT • Without driver's dashboard under cover: PANEL Secure through the existing hole for under cover securing. WIRE TIE View from below 12 mm CENTER (
Краткое содержание страницы № 14
www.collegehillshonda.com 48. Disconnect the vehicle 42-pin, 4-pin and 2-pin 49. Plug the engine starter harness 4-pin and 2-pin connectors. connectors into the fuse box. NOTICE Check that the engine starter harness 4-pin VEHICLE 4-PIN and 2-pin connectors are connected to the fuse box VEHICLE 2-PIN CONNECTOR and they are locked securely. Loosely connected CONNECTOR connectors can cause engine stall during driving. VEHICLE 42-PIN CONNECTOR FOAM 2-PIN 4-PIN FUSE BOX CUSHION CONNECTOR VEHICLE FU
Краткое содержание страницы № 15
www.collegehillshonda.com 51. Connect the engine starter harness 18-pin 53. Install the clip from the engine starter harness to connectors with each other and secure them with the fuse box bracket behind the fuse box. a wire tie to the vehicle harness. GROUND BOLT (Reuse.) ENGINE STARTER FRONT HARNESS 18-PIN CONNECTORS ENGINE STARTER HARNESS GROUND TERMINAL ENGINE STARTER CLIP HARNESS WIRE TIE VEHICLE HARNESS 6D01331T FUSE BOX BRACKET 52. Unplug the white vehicle 14-pin connector at the 6D01181T
Краткое содержание страницы № 16
www.collegehillshonda.com 58. Using isopropyl alcohol on a shop towel, clean the Installing the Control Unit area where the engine starter label will attach. 55. Connect the antenna cable terminal and the engine starter harness 18-pin connector to the control unit. HOOD ANTENNA CABLE TERMINAL (Connect first.) ADHESIVE BACKING ENGINE STARTER LABEL 6D01421T FRONT CONTROL UNIT 59. Attach the engine starter label to the back of the CONTROL UNIT ENGINE STARTER hood. BRACKET 6D01312T HARNESS 18-PIN 60
Краткое содержание страницы № 17
www.collegehillshonda.com REMOTE ENGINE STARTER REGISTRATION 5. Select Honda Systems, then click the check button. 1. Acquire the PCM code from ISIS. 2. Connect the HDS tester to the OBD II data link connector, then turn the ignition switch to the ON (II) position. 3. Start the HDS, and click the car icon. CAR ICON Select CHECK BUTTON “Honda Systems.” 752503AS 6. Select R/C ENG STARTER and click the check button. 752501AS 4. Input the VIN and other required information into the HDS, then click
Краткое содержание страницы № 18
www.collegehillshonda.com 7. A REMARKS message will display. Click the 9. The following message will display: Obtain PCM- check button. code (IMMOBILIZER PCM CODE) from iN. This vehicle’s VIN will be required to obtain the password. (USA). Click the check button. “REMARKS” message “Obtain PCM-code" message CHECK BUTTON 752505AS CHECK BUTTON 8. Select REGISTER REMOTE CONTROL ENGINE 752507AS STARTER UNIT, then click the check button. 10. Input the PCM Code, then click the check button. NOTE: To
Краткое содержание страницы № 19
www.collegehillshonda.com 11. The following message will display: The registration of the Remote Control Engine Starter Unit has been completed. Click the check button. "Registration" message CHECK BUTTON 752510AS 12. The following message will display: Check that the engine can be started by the Transmitter. Click the check button. “Check that the engine can be started by the Transmitter” CHECK BUTTON 752511AS 13. Perform the function check on page 21, then disconnect the HDS. © 2008 American
Краткое содержание страницы № 20
www.collegehillshonda.com FUNCTION CHECK Operating Conditions • The hood is closed. • Shift lever is in Park. • The key is not in the ignition switch. • All doors and trunk are closed and locked. Inspection 1. Within 1 second, press the command button and then the start button on the transmitter. The engine should start if all operating conditions are met. Does the engine start? Yes - Operation is normal. No: • Make sure all operating conditions are met. • Check the engine starter harness connec
