Краткое содержание страницы № 1
1 16 65 5B B
➤ O Ow wn ne er r’’s s//IIn ns stta alllla attiio on n G Gu uiid de e
Краткое содержание страницы № 2
lliim miitte ed d lliiffe ettiim me e c co on ns su um me er r w wa ar rr ra an ntty y Directed Electronics, Inc. (hereinafter "Directed") promises to the original purchaser to repair or replace with a comparable reconditioned Directed DIY remote start unit if this Directed DIY remote start unit (hereinafter "Unit"), excluding without limitation, any remote transmitters or associated accessories, proves defective in materials or workman- ship under normal use for the life of the vehicle which
Краткое содержание страницы № 3
OR IN CONNECTION WITH THE INSTALLATION, USE, IMPROPER USE, OR INABILITY TO USE, THE PRODUCT, EVEN IF THE PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. SOME STATES DO NOT ALLOW THE EXCLUSION OF LIMITATION OF INCIDENTAL OR CON- SEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS OR EXCLUSION MAY NOT APPLY TO YOU. THE CONSUMER AGREES AND CONSENTS THAT ALL DISPUTES BETWEEN THE CONSUMER AND DIRECTED SHALL BE RESOLVED IN ACCORDANCE WITH CALIFORNIA LAWS IN SAN DIEGO COUNTY, CALIFORNIA. I IM MP PO
Краткое содержание страницы № 4
tta ab blle e o off c co on ntte en ntts s lli im mi it te ed d lli if fe et ti im me e c co on ns su um me er r w wa ar rr ra an nt ty y.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. i i w wh ha at t i is s i in nc cllu ud de ed d.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .
Краткое содержание страницы № 5
© 2004 Directed Electronics, Inc. 2
Краткое содержание страницы № 6
w wh ha att iis s iin nc cllu ud de ed d ➤ Control Module ➤ One 4-Button Transmitter ➤ 8-Pin Main H/1 Harness ➤ 6-Relay Wires ➤ Shutdown Toggle Switch ➤ Hood Pin Switch ➤ 10 feet of Black Electrical Tape ➤ 6 Six inch Zip Ties ➤ LED Tester ➤ Razor Knife ➤ CDROM—Do-It-Yourself Installation Video Additional parts may be required (such as relays or immobilizer). iin ns stta alllla attiio on n tto oo olls s ➤ Digital Multi-Meter ➤ Drill 9 5 ➤ /32 and /16 Drill Bits ➤ Screwdrivers (Phillips and Fl
Краткое содержание страницы № 7
iim mp po or rtta an ntt iin nffo or rm ma attiio on n Congratulations on the purchase of your remote start system. This system will allow convenient remote start of your vehicle. Properly installed, this system will provide years of trouble-free operation. Please take the time to carefully read this User’s Guide in its entirety and watch the Do-It-Yourself Installation Video (CDROM) prior to installing your system. You can print additional or replacement copies of this manual by accessing the
Краткое содержание страницы № 8
fcc/id notice ➜ This device complies with Part 15 of FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesirable operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this device. w wa ar rn niin ng g! ! s sa affe etty y ffiir rs stt The following
Краткое содержание страницы № 9
transmitters to assure that the system does not uninten- tionally remote start the vehicle. 4. T TH HE E U US SE ER R M MU US ST T I IN NS ST TA AL LL L A A C CA AR RB BO ON N M MO ON NO OX XI ID DE E D DE ET TE EC CT TO OR R I IN N O OR R A AB BO OU UT T T TH HE E L LI IV VI IN NG G A AR RE EA A A AD DJ JA AC CE EN NT T T TO O T TH HE E V VE EH HI IC CL LE E.. A AL LL L D DO OO OR RS S L LE EA AD DI IN NG G F FR RO OM M A AD DJ JA AC CE EN NT T L LI IV VI IN NG G A AR RE EA
Краткое содержание страницы № 10
start module must be removed or properly reinstalled so that O OP PE ER RA AT TI IO ON N O OF F T TH HE E the vehicle does not start in gear. R RE EM MO OT TE E S ST TA AR RT T M MO OD DU UL LE E I IF F T TH HE E V VE EH HI IC CL LE E S ST TA AR RT TS S I IN N G GE EA AR R I IS S C CO ON NT TR RA AR RY Y T TO O I IT TS S I IN NT TE EN ND DE ED D M MO OD DE E O OF F O OP PE ER RA AT TI IO ON N.. O OP PE ER RA AT TI IN NG G T TH HE E R RE EM MO OT TE E S ST TA AR RT T S SY YS
Краткое содержание страницы № 11
p pr riim ma ar ry y h ha ar rn ne es ss s ( (H H//1 1) ),, 8 8- -p piin n c co on nn ne ec ctto or r H H1 1/ /1 1 BLUE (-) 200mA Status Output H H1 1/ /2 2 VIOLET/WHITE Tachometer Input (optional) H H1 1/ /3 3 BROWN (+) Brake Switch Shutdown Input GRAY (-) Hood Pin Shutdown Input H H1 1/ /4 4 H H1 1/ /5 5 BLACK Ground H H1 1/ /6 6 WHITE/BLUE (-) Remote Start Activation Input LT. GREEN/BLACK Factory Alarm Disarm H H1 1/ /7 7 H H1 1/ /8 8 WHITE (-) Parking Light Flash Output (optional) r re e
Краткое содержание страницы № 12
u us siin ng g L LE ED D tte es stt p pr ro ob be e note: Do not use this test probe on computerized equip- ment as damage can result. To use the LED test probe: 1. Remove the protective cover off the probe tip. Save the protective cover for reinstallation on the probe tip when the LED tester is not being used. 2. Connect the Black clip to a good chassis ground. 3. Connect the Red clip to a good +12V source. Both the Red and Green LEDs should be illuminated dimly. 4. If a positive voltage sou
Краткое содержание страницы № 13
iin ns stta alllla attiio on n Be sure to read this section thoroughly and view the Do-It- Yourself Installation CDROM video in its entirety before starting the installation. Pay special attention to all warnings to prevent personal injury or damage to your vehicle. w ww ww w..b bo oa as se ec cu ur ri it ty y..c co om m Visit our 24-hour technical Web site ( )to get a vehicle-specific wiring guide prior to starting this installa- tion. If at any time during the installation you are unable to an
Краткое содержание страницы № 14
step 1 ➜ Ground Wire The BLACK (H1/5) wire on the main 8-pin harness is ground. This wire should be connected to a clean, paint-free area of metal in the drivers kick panel area. First strip back a ¾-inch section of the insulation off the BLACK wire and crimp a ring terminal (not provided) to that wire. Locate a clean, paint-free metal surface in the drivers kick panel. Using a self-tapping screw, drill the screw with the ring terminal to the metal area. Once screwed down, pull on the wire to en
Краткое содержание страницы № 15
step 2 ➜ Constant Power and Ignition wires Almost all power and ignition wires can be found behind the key cylinder under the lower drivers side dash panel. Using the appropriate hand tools, remove the lower dash panel using care not to break any parts. If the panel does not come off easily check for any additional screws you may have missed. Once the lower dash panel has been removed, locate the ignition harness at the back of the key cylinder. This is usually a group of thicker wires. With the
Краткое содержание страницы № 16
warning! Before making any connection to constant battery power make sure that the two green 30 amp fuses are removed from the fuse holders on the two thick red wires. Failure to do so may cause fire or shorting of sensitive electrical components. Once the constant power wire (or wires) has been identified, solder the two thick RED wires from the control module to it and cover the connection with electrical tape to ensure a safe connection. With the black lead still in the kick panel, locate the
Краткое содержание страницы № 17
If the vehicle requires more than one ignition as per the Web site information follow the same test procedure and solder the thick PINK/WHITE (F) relay wire to it and be sure to wrap the connection with electrical tape. If your vehicle requires more than two ignitions, contact BOA Technical Support. step 3 ➜ Accessory and Starter wires The starter and accessory wires will be located in the same harness as the ignition and constant power. To find the accessory wire leave the LED tester black lead
Краткое содержание страницы № 18
Now that the accessories have been located, find the wire suspected to be the starter wire according to the web information on your vehicle. Place the red lead of your LED tester on the wire. With the key in the off position the LED tester should be extinguished in all key positions except the crank position. In the crank position your LED tester should illuminate, and will extinguish when the starter disengages. n no ot te e:: Always check the Web site information on your vehicle for warnings r
Краткое содержание страницы № 19
step 4 ➜ Safety Shutdown Wires important! These wires are meant to protect the vehicle and anyone near the vehicle. They must be connected appropriately to prevent damage to the vehicle and possi- ble bodily injury. Failure to properly install these wires may cause the vehicle to lunge if remote started while in gear. With all ignition wires properly connected, find the appropriate safety shutdown wires. These are the brake wire and hood pin wires. First locate the factory brake wire using your
Краткое содержание страницы № 20
Installing the hood pin switch requires drilling a ¼-inch hole in the metal lip under the hood. Choose a location that will allow the pin switch to be depressed when the hood is closed. The pin switch has a spade connector on the bottom for the wire connection. Place the wire with the spade connector onto the pin switch and run the wire into the vehicle’s passenger compartment through a factory rubber grommet. Using a sharp, pointed object poke a hole into the grommet and attach the wire to the
