Краткое содержание страницы № 1
EZ-3 and EZ-4
1-WAY REMOTE START SYSTEM
OPERATING INSTRUCTIONS
CONGRATULATIONS on your choice of a Cool Start™ Remote Engine Starter and Keyless Entry with DP
Technology by Crimestopper Security Products Inc. This booklet contains the information necessary for operating
your system. If any questions arise, contact your installation dealer or Crimestopper Security Products Inc.
*IMPORTANT INFORMATION: Primary and Optional Features
-PRIMARY: These are features that
Краткое содержание страницы № 2
TABLE OF CONTENTS Operation Cautions & Warnings…….……………..….…………………………………….…………….….…………2 Using the Remote Transmitter………………………………………………………………………….………....…….3 Status LED……………………………………………………………………………………………….……….……….4 Remote Engine Control…………….…..……………………………………………………………….…….……….4-7 Turbo Timer Mode……………………………….……………………………………...……………….…………..…8-9 Convenience and Safety Features……………………………….………………………………….…...……..…10-11 Transmitter Programming….…………….…………………………………………….……………….…………....…12 2 Veh
Краткое содержание страницы № 3
USING THE REMOTE TRANSMITTER UP SLIDE COVER FLASHLIGHT 2nd VEHICLE DOWN For RS-3DP II The transmitter supplied with this system has 3 buttons, a flashlight and a car 2 side button. The button configuration is Factory-set and unchangeable. See Page 13 for additional information on how to use your remote to operate a second vehicle equipped with an RS-3 series system. For RS-4DP II The transmitter supplied with this system has 4 buttons, a flashlight and a car 2 side butt
Краткое содержание страницы № 4
STATUS LED LED Operation: (Optional, requires Installation of LED) LED will flash when locking your doors with remote. LED will remain solid in Valet Service Mode. REMOTE ENGINE CONTROL Remote Start & Auxiliary Output – Button Press Selection (Option # 6): To eliminate the possibility of accidentally opening the trunk or starting the vehicle, there are (3) options for button press selection. This option will allow you to change whether the Remote starter and Trunk release activate
Краткое содержание страницы № 5
REMOTE ENGINE CONTROL REMOTE ENGINE STARTING - UNSUCCESSFUL START In the event that the engine does not start on the first attempt, the system shuts down for a few seconds, then nd rd attempts to restart the engine a 2 and 3 time. For hard starting engines, the unit will allow a starter crank time of up to13 seconds maximum. This should provide ample cranking time for difficult starts, but is limited to 13 seconds to help prevent damage to the starter from over cranking. nd rd 1) If en
Краткое содержание страницы № 6
REMOTE ENGINE CONTROL IDLE DOWN MODE: This mode allows the unit to take over operation of the parked vehicle while the ignition key is removed and you exit the vehicle. The vehicle is put into a remote running condition before you exit and it will remain running for the programmed run time or until you come back. Examples: • You pull up to a convenience store for a quick stop, "Idle Down" mode keeps engine running when you exit the vehicle, (with keys in hand) remote lock doors or ar
Краткое содержание страницы № 7
REMOTE ENGINE CONTROL INFINITY RUN MODE This mode can only be activated with "Idle Down" procedure. The Infinity Run mode allows the vehicle engine to remain running INDEFINITELY after the programmed run time elapses. This mode will allow the vehicle to be left running and unattended without the ignition key in the switch preventing the vehicle from being stolen. This mode can be beneficial to law enforcement or commercial trucks that need to remain running unattended for long periods
Краткое содержание страницы № 8
TURBO TIMER MODE (OPTION #22) The optional Turbo Timer mode allows the CoolStart system to keep a Turbo or Turbo Diesel vehicle running for 1 to 5 minutes [selectively] after you remove the key and exit the vehicle. This is handy for turbo cool-down without the need for expensive turbo timers. This mode requires the use of an extra part called a momentary switch/button that is not included with the kit. There are (3) modes of operation for the Turbo Timer Mode 1. Brake Pedal Set Mo
Краткое содержание страницы № 9
SETTING THE TURBO TIMER RUN TIME PRESS TURBO RELEASE PRESS TIMER BUTTON RUNNING BRAKE AND HOLD 1-5 TIMES BRAKE LIGHTS REMOVE KEY FLASH 1-5X REMAIN RUNNING 1-5 MIN. EXIT VEH. 9
Краткое содержание страницы № 10
CONVENIENCE AND SAFETY FEATURES KEYLESS ENTRY (POWER DOOR LOCK CONTROL, Optional) This system enables you to remotely lock and unlock the vehicle’s doors (if equipped with power locks) via remote control for safety and convenience. Note: This feature may require extra labor and/or parts to install. Press the Lock or Unlock transmitter button as you leave or come near the vehicle. Parking lights will flash once for lock and twice for unlock. If vehicle is running by the remote start s
Краткое содержание страницы № 11
CONVENIENCE AND SAFETY FEATURES VALET MODE / REMOTE START DISABLE (Requires Installation of Valet Switch) Before servicing your vehicle or handing the keys over to a Valet we recommend putting the unit into Valet Mode. The remote start function WILL NOT operate when in Valet Mode. To enter Valet mode, turn the key to the ON position, press and hold Program/Valet switch for 5-6 seconds. The LED will turn on solid when the system is in Valet Mode. To exit Valet Mode, perform this proced
Краткое содержание страницы № 12
TRANSMITTER PROGRAMMING Note: All transmitter codes must be learned at time of programming!! The RS-4 learns up to 4 different transmitter codes. 1. Turn key to the ON position. (Pink wire must be connected.) 2. Press Programming button 4 times, then after a few seconds the unit flashes the parking lights 4 times. 3. Press button #1 of the transmitter to be coded. You should get 2 light flashes indicating the unit is waiting for a nd rd 2 code, then press button #1 of a second t
Краткое содержание страницы № 13
2-VEHICLE OPERATION & PROGRAMMING A single Remote Control can control two different vehicles. SETUP: Follow the “Transmitter Programming” steps on the second vehicle below. Program Car #2’s existing remotes, then quickly press the Car #2 side button on your remote before pressing the lock button on your remote to program it to Car #2. Once your remote is programmed to the second vehicle, press the car #2 side button on your remote first, and within 3 seconds press any of the 4 funct
Краткое содержание страницы № 14
NO FACTORY KEYLESS ENTRY AFTER REMOTE START Most new cars Do Not allow the factory Remote Keyless Entry to function with the Ignition ON. This means you can’t use the factory remote to lock or unlock the doors. After remote start you have to use the keys to unlock the door. Also, many new vehicles unlock the doors when disarming the factory alarm. This leaves the doors unlocked while Remote Started. To resolve this problem, have your installer connect the door locks to the Remote Start Key
Краткое содержание страницы № 15
BATTERY REPLACEMENT To replace the battery: Simply remove the 3 screws on back of the transmitter and open the case. Remove the battery and replace. The replacement battery is GP23A. Remove 3 Screws 15
Краткое содержание страницы № 16
2-Way DATA PORT Some vehicles require a Databus Module to Bypass the factory Immobilizer and operate the keyless entry Databus modules are used to communicate with the vehicles computer at the OBD2 Data connector or Canbus wires. This reduces installation error. Crimestopper Systems with DP Series have a direct Data Port Plug-In for the Databus bypass module. This eliminates conventional wiring between the Alarm/Remote Starter and the bypass interface module. Features Include • Tran
