Краткое содержание страницы № 1
Installation Free-Standing
Electric Ranges
Instructions
Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: www.GEAppliances.com
EER3000, EER3001, JBP24, JBP25, JBP26, JBP35, JBP48, JBP64, JBP66, JBP67, JBP68, JBP69,
JBP71, JBP78, JBP80, JBP82, JBP83, JBP84, JBP99, JB600, JB710, JB905, JB968, JB988, JBS55
BEFORE YOU BEGIN ANTI-TIP DEVICE
Read these instructions completely
WARNING — To reduce the risk
and carefully.
of tipping, the appliance must be secured by
properly installe
Краткое содержание страницы № 2
Installation Instructions PREPARE TO INSTALL THE RANGE FOR YOUR SAFETY: MATERIALS YOU MAY NEED All rough-in and spacing dimensions must be met for safe use of your range. Electricity to the range can be disconnected at the outlet Tin Snips Lag Bolts Anchor Sleeves without moving the range if the outlet is in the preferred location (remove lower drawer). (For Anti-Tip Bracket Mounted on Concrete Floors Only) To reduce the risk of burns or fire when reaching over hot surface elements, cabinet sto
Краткое содержание страницы № 3
Installation Instructions PREPARE THE OPENING 2 See illustrations for all rough-in and spacing dimensions. The range may be placed with 0” clearance (flush) at the back wall and side walls of **30” Min. the cabinet. ***6” Min. **15” Min. Acceptable electrical outlet area. 1 2 ⁄2” Orient the electrical receptacle so the length 25” is parallel to the floor. 1 2 ⁄2” *0” *0” MINIMUM DIMENSIONS BETWEEN COOKTOP, 1 7 ⁄2” 36” WALLS AND ABOVE THE COOKTOP: *** Make sure the wall covering, countertop and
Краткое содержание страницы № 4
Installation Instructions ELECTRICAL CONNECTIONS Use only a 3-conductor or a 4-conductor ELECTRICAL REQUIREMENTS UL-listed range cord. These cords may be provided with ring terminals on wire and CAUTION: For personal safety, a strain relief device. do not use an extension cord with this appliance. Remove house fuse or open circuit A range cord rated at 40 amps with 125/250 breaker before beginning installation. minimum volt range is required. A 50 amp range cord is not recommended but if used,
Краткое содержание страницы № 5
Installation Instructions C For power cord installations only (see 3 POWER CORD AND the next step if using conduit), assemble STRAIN RELIEF INSTALLATION the strain relief in the hole. Insert the power cord through the strain relief and A Remove the wire cover (on the back of tighten. Allow enough slack to easily the range) by removing five (5) screws attach the cord terminals to the terminal using a 1/4” nut driver. block. If tabs are present at the end of Do not discard these screws. the winge
Краткое содержание страницы № 6
Installation Instructions ELECTRICAL CONNECTIONS (CONT.) 4 3-WIRE POWER CORD 5 4-WIRE POWER CORD INSTALLATION INSTALLATION The neutral or ground The neutral wire of WARNING: WARNING: wire of the power cord must be connected the supply circuit must be connected to the to the neutral terminal located in the neutral terminal located in the lower center center of the terminal block. The power of the terminal block. The power leads must leads must be connected to the lower left be connected to the
Краткое содержание страницы № 7
Installation Instructions 6 3-WIRE CONDUIT INSTALLATION 7 4-WIRE CONDUIT INSTALLATION A Loosen the 3 lower terminal screws from A Loosen the three lower terminal screws the terminal block. Insert the center bare from the terminal block. Remove the ground wire (white/neutral) tip through the bottom screw and ground plate and retain them. center terminal block opening. On certain Cut and discard the ground strap. DO NOT models, the wire will need to be inserted DISCARD ANY SCREWS. through the gro
Краткое содержание страницы № 8
Installation Instructions INSTALL THE RANGE 8 REPLACE THE WIRE COVER 10 REMOVE STORAGE DRAWER Replace the wire cover on the range back A Pull the drawer out until it stops. by sliding its left edge under the retaining B Lift the front of the drawer until the tabs and replacing the five screws removed stops clear the guide. earlier. Make sure that no wires are pinched between the cover and the range back. 5 screws to replace wire cover Stop Retaining tabs C Remove the drawer. Back of Wire range
Краткое содержание страницы № 9
Installation Instructions 11 LEVEL THE RANGE 13 FINAL INSTALLATION CHECKLIST A Install the oven shelves in the oven and position the range where it will be installed. • Check to make sure the circuit breaker is closed (RESET) or the circuit fuses are Check for levelness by B replaced. placing a spirit level or Spirit level a cup, partially filled • Be sure power is in service to the building. with water, on one of the oven shelves. If • Check to be sure that all packing materials using a spirit
Краткое содержание страницы № 10
Notes 10
Краткое содержание страницы № 11
Notes 11
Краткое содержание страницы № 12
Printed in the United States 12
