Краткое содержание страницы № 1
OWNER’S MANUAL
3LCD DATA PROJECTOR
TLP-X2000
TLP-XC2000 (With Document Camera)
TLP-X2000
Others Maintenance Operations Preparations Before Using
Краткое содержание страницы № 2
Before Using SAFETY PRECAUTIONS The lightning flash with arrowhead symbol, within an equilateral triangle, is intended - Reorient or relocate the receiving antenna. to alert the user to the presence of uninsulated "dangerous voltage" within the product's - Increase the separation between the equipment and receiver. enclosure that may be of sufficient magnitude to constitute a risk of electric shock to - Connect the equipment into an outlet on a circuit different from that to which the receiver i
Краткое содержание страницы № 3
IMPORTANT SAFETY INSTRUCTIONS CAUTION:PLEASE READ AND OBSERVE ALL WARNINGS AND 5. Heat 8. Power-Cord Protection INSTRUCTIONS GIVEN IN THIS OWNER'S MANUAL AND THOSE The product should be situated Power-supply cords should be MARKED ON THE UNIT. RETAIN THIS BOOKLET FOR FUTURE away from heat sources such as routed so that they are not likely to REFERENCE. radiators, heat registers, stoves, or be walked on or pinched by items other products (including placed upon or against them, This unit is fully
Краткое содержание страницы № 4
IMPORTANT SAFETY INSTRUCTIONS (Continued) e) If the product has been dropped or 10. Lightning storms 12. Do not place the product 15. Accessories damaged in any way (If the cabinet For added protection for this vertically Do not place this product on an should break, please handle with product during storm, or when it is unstable cart, stand, tripod, Do not use the product in the care to avoid injury) . left unattended and unused for bracket, or table. The product may upright position to proje
Краткое содержание страницы № 5
IMPORTANT SAFETY INSTRUCTIONS (Continued) POWER SUPPLY CORD SELECTION If your line voltage is 220 to 240V, use one of the following types of cable. 19. Replacement Parts 23. Do not look into the laser When replacement parts are light source of the remote Plug Plug required, be sure the service control or direct the laser configuration Plug type Line voltage configuration Plug type Line voltage technician has used replacement pointer toward a person or Australian 200 – 240V parts specified by th
Краткое содержание страницы № 6
IMPORTANT PRECAUTIONS (Continued) Avoid Volatile Liquid Disposal Do not use volatile liquids, such as an insect spray, near the unit. Do not leave rubber or This product contains substances which are harmful to humans and the environment. plastic products touching the unit for a long time. They will leave marks on the finish. • The lamp contains mercury. If cleaning with a chemically saturated cloth, be sure to follow the product's precautions. Please dispose of this product or used lamps in
Краткое содержание страницы № 7
CONTENTS Before Using Maintenance SAFETY PRECAUTIONS .................................................................................. 2 About lamp ......................................................................................................... 49 IMPORTANT SAFETY INSTRUCTIONS ........................................................... 4 Lamp replacement ............................................................................................. 50 POWER SUPPLY CORD SELECTION ........
Краткое содержание страницы № 8
Preparations Checking the package contents Names of each part on the main unit Please make sure that the following items are included in the box, along with the main unit. (4) (8) (5)(6) (3) (2)(16)(1) If any item is missing, please contact the store immediately where you purchased the product. (1) (5) (8) (6) (2) (10) (9) (7) (7) (12) (13) (11) (12) (14)(15) (3) Back Front (4) Name : Function p.20 (1) Infrared remote sensor : Senses commands from the remote control. p.28 (2) Foot adjuster
Краткое содержание страницы № 9
Names of each part on the control panel and remote control Name : Main Function Control panel Remote Control (TLP-X2000) (13)AUTO SET button : Sets up input from computer. p.29 (9) (5) (10) Remote control Warning label (14) Laser indicator : Lights when laser is on. Laser light transmitter p.21 source (15) Mouse control button : Controls a mouse pointer. ® p.21 (16)PAGE+ button : Proceeds PowerPoint slides. (1) (14) p.31 (4) (17) MUTE button : Cuts off the picture and sound temporarily. (13)
Краткое содержание страницы № 10
Names of the terminals on the rear panel Names of each part on the document camara (models with a document camera) (1) (2) (3) (4) (6) (8) (9) (1) (2) (3) (4) (9) (6) (10) (7) (11) (8) (8) (5) (7) (5) Name : Main Function Name : Main Function (1) CONTROL terminal : When operating the projector via a computer, connect Camera p.59 this to the controlling computer’s RS-232C port. (1) LED illumination : The illumination LED for referring documents. p.46 (2) AUDIO (L/R) terminal : Input audio signal
Краткое содержание страницы № 11
Approx. 5m Preparing and using the remote control Operating a computer using the remote control A computer can be operated using the projector’s remote control. This function is available ■ Loading dry-cell batteries ■ Operating the remote ® ® ® on any computer with the Windows 98/98SE, Windows Me, Windows 2000, or Win- into the remote control control ® dows XP OS, that is equipped with a USB port which can support USB1.1 (The mouse q Remove the battery cover. Turn on the ON/OFF switch of the r
Краткое содержание страницы № 12
Placement Connection Placement Styles Before connection As shown in the figures below, this device can be placed in 4 different styles. • Read the owner’s manual of the device you are connecting to the projector. The factory setting is “floor-mounted front projection.” Set the [Projection mode] in the • Some types of computer cannot be used or connected to this projector. p.43 p.57 Default setting 2 menu, in accordance with your needs. Check for an RGB output terminal, supported signal , etc. •T
Краткое содержание страницы № 13
Operations Connection (Continued) Turning the power on and off Notes ■ Connecting the power cord • When COMPUTER 2 IN terminal (also used for MONITOR OUT terminal) is used as Insert the power cord connector into 1 MONITOR OUT terminal, the signal which is input to COMPUTER 1 IN terminal is output. the AC IN socket of the projector. • Signals are output from MONITOR OUT terminal even in standby mode. However, from AUDIO OUT terminal, no audio signal is output. Insert the power cord plug into a
Краткое содержание страницы № 14
Turning the power on and off (Continued) Basic operations Notes Turn on the power. 1 p.25 Turn on the power by following the instructions in “Turning the power on” . • The start-up screen will disappear after a moment. You can dismiss the start-up screen before this by performing any operation. You can also configure the start-up screen not to p.39 appear via the Display setting menu . 2 Select the language and the lamp power (When using the • The first time you use the projector after purchase,
Краткое содержание страницы № 15
Basic operation (Continued) Using handy features 5 Projector placement angle adjustments ■ Using auto setting (Only for input from computer) Remote This function sets up the projector to the optimum state such as The placement angle and the height of the projected image can be adjusted by the foot Control sampling phase, frequency, screen position, and clamp for each adjuster. type of the input signal by using simple operations. q Lift up the front of the projector to the desired angle, then pre
Краткое содержание страницы № 16
Using handy features (Continued) Adjusting Keystone distortion [Auto] Notes • The icon appears while resizing. 2 Press the button. • Operating a function other than Mute will release resizing. The keystone distortion is automatically corrected. The icon appears during this • As zooming is processed digitally, the image quality is degraded in larger zoom correction. ratio. When adjustment is finished, the Keystone menu appears again. For fine adjust- • During resizing or moving the zooming are
Краткое содержание страницы № 17
Using handy features (Continued) ■ Changing screen size ■ Setting the password Remote The screen size for the projected image can be changed. How to change password Control The default password is 0000. Press the remote control’s SCREEN SIZE button. 1 Select [Password] in the Default setting 2 menu and press the or Pressing the button switches Full/Thru/Wide in turn. button. Notes 2 • Thru display is available for computer-input images. Select [Password registration] in the password registrati
Краткое содержание страницы № 18
Using handy features (Continued) How to set password (from [Off] to [On]) How to set password (from [On] to [Off]) 1 1 Select [Password] in the Default setting 2 menu and press the or Select [Password] in the Default setting 2 menu and press the or button. button. The password entry screen is displayed. 2 Select [Password setting] in the password registration, setting menu, 2 Enter the password using numeric keys of the remote control. and press the or button. 3 Select [Password setting] in
Краткое содержание страницы № 19
Using the menus You can call up on-screen menus, and conduct a number of adjustments and settings using ■ The image adjustment menu p.16 the operation buttons on the control panel (main unit side) and remote control. Use this menu to set or adjust image-related items. Items that can be set or adjusted are marked with “Yes”, and those that cannot are marked with “No”. (When an item is masked, ■ How to use the menus it indicates that you cannot select for the current input.) The menu shown below
Краткое содержание страницы № 20
Using the menus (Continued) ■ The display setting menu Camera Item Description Computer Y/PB/PR Video S-video (XC2000) Use this menu to set screen display-related items. (The items in gray color cannot be set with the current input selection.) Position V-position Yes No No No No Adjust the vertical position of the image. Description Item Clamp 1 Yes No No No No Screen size Adjusts the clamp pulse position. (Full): Display with 1024 × 768 dot resolution Clamp 2 Yes No No No No (Thru): Disp
