Краткое содержание страницы № 1
Installation/Operating Instructions
220 V Revelation Video Projector Mount by Draper
These Installation/Operating Instructions are available in the offi cial language
Where to install the Revelation
of the country where you purchase the product. Please contact your
To determine where to mount the Revelation, you need to know the fol low ing:
distributor to request a copy.
➀ The projector manufacturer’s rec om mend ed throw distance (TD). Typically,
Vous pourriez demander les instructions d’inst
Краткое содержание страницы № 2
220 V Revelation by DRAPER Page 2 of 8 ➃ Bottom of unit must be unobstructed after installation. 432mm minimum sary connections and plug the power cord of the pro jec tor into the receptacle clearance is required below the door. provided in the electrical chas sis. Power to the Revelation should be turned off any time electrical connections or mechanical ad just ments are made ➄ Access should be provided to electrical control box in case service is to the Revelation! Cycle the mir rored door
Краткое содержание страницы № 3
220 V Revelationby DRAPER Page 3 of 8 should be secured into place using the eight projector stand offs pro vid ed. Two Important: Once the adhesive is placed onto the surface of the inner pan it is of the standoffs have a removable hook and loop material to be used at the very diffi cult to remove. It is very important to plan ahead when placing these rear of the projector for ease of removing the projector. The stand offs will en- standoffs around the projector. sure proper re lo ca tion o
Краткое содержание страницы № 4
220 V Revelation by DRAPER Page 4 of 8 Revelation Dimensions 6 Mounting 3/ holes 9.525mm ( 8") dia. TB1 Electrical 252 hook-up mm *1 8 Projector 972 standoffs mm 946 462mm mm Lens and mirror 603 *4 centerline mm Projector 165 mm 65 mm 25 4" 51mm *2 *2 mm *3 248 mm Model A Model B *1 232mm 475mm Minimum rough opening *2 330mm 457mm 597mm x 597mm *3 864mm 1118mm *4 546mm 630mm Minimum clearance (Includes allowance for housing in plenum) Minimum clearance Models A & B-346mm without Plenum 33
Краткое содержание страницы № 5
1 2 3 45 67 8 9 10 12 3 4 5 679 8 10 1 23 4 56 7 89 10 11 12 Red Brown Yellow Green White 12 3 456789 10 11 12 Black Eye Port for IR Eye, RF Receiver or LED Switch. If more than one of these three is used with one LVC-III, a splitter is required. 3 Button Wall Switch DOWN - Black COM - White UP - Red Aux Port for connecting additional LVC-III modules (up to six total-connect from Aux to Eye). 220 V Revelation by DRAPER Page 5 of 8 Wiring Diagrams for Revelation without Plenum Single Station Co
Краткое содержание страницы № 6
1 10 CB1A CB1B 1 10 1 12 1 235 4 6 7 8 9 10 I 12 346 5 7 8 9 10 11 12 220 V Revelation by DRAPER Page 6 of 8 Field Installation of Plenum Kit Caution! Disconnect power from the Revelation before installing ple- FIGURE #1 num. TB1 T2 transformer ➀ Remove the covers from the electrical chassis in the Revelation. T2 Nylon tape 43" long TB1 F4 CR1 F5 TB2 ➁ Disconnect the black 14 awg. wire that runs from the T2 trans form er to CR2 T1 Wire
Краткое содержание страницы № 7
1 2 34 5 6 78 9 10 I 1 2 34 5 6 7 8 9 10 1 2 3 4 5 6 781 9 0 11 12 I 1 2 3 4 5 6 7 8 9 10 11 12 220 V Revelation by DRAPER Page 7 of 8 Plenum Operating Instructions The Revelation plenum features a unique design that allows easy access to in the Revelation circuitry turns on the fans anytime the projector is op erat ing virtually anywhere inside the unit. Access is achieved by removing either end and circulates fresh air through the unit. Two 4" duct fl anges are located on panel. End panels f
Краткое содержание страницы № 8
220 V Revelation by DRAPER Page 8 of 8 VIC12 Kit Installation Instructions The VIC 12 KIT includes all the components necessary for the VIC 12 to work with the Revelation. Follow these steps to install the components in this KIT. FIGURE #1 ➀ Close the door to the Revelation. ➁ DISCONNECT POWER TO THE REVELATION. ➂ Remove the covers from the electrical enclosure. CR 1 TB 2 ➃ Attach the pre-wired limit switch [1] to the shaft mounting bracket which Motor CR 2 is closest to the motor as shown
