Краткое содержание страницы № 1
MS502/MX503
Digital Projector
User Manual
Краткое содержание страницы № 2
Table of contents Direct power off..................................... 33 Important safety Menu operation ...................................... 34 instructions ........................... 3 Maintenance........................ 43 Introduction.......................... 7 Care of the projector............................ 43 Projector features.....................................7 Lamp information ................................... 44 Shipping contents......................................8 Trou
Краткое содержание страницы № 3
Important safety instructions Your projector is designed and tested to meet the latest standards for safety of information technology equipment. However, to ensure safe use of this product, it is important that you follow the instructions mentioned in this manual and marked on the product. Safety Instructions 1. Please read this manual before 5. In some countries, the line voltage is you operate your projector. Save NOT stable. This projector is it for future reference. designed to operate
Краткое содержание страницы № 4
Safety Instructions (Continued) 7. The lamp becomes extremely hot 10. Do not place this product on an during operation. Allow the projector unstable cart, stand, or table. The to cool for approximately 45 minutes product may fall, sustaining serious prior to removing the lamp assembly damage. for replacement. 11. Do not attempt to disassemble this 8. Do not operate lamps beyond the projector. There are dangerous high rated lamp life. Excessive operation of voltages inside which may c
Краткое содержание страницы № 5
Safety Instructions (Continued) 13. Do not place this projector in any of 14. Do not block the ventilation holes. - Do not place this projector on a the following environments. blanket, bedding or any other soft - Space that is poorly ventilated or surface. confined. Allow at least 50 cm - Do not cover this projector with a cloth clearance from walls and free flow of air or any other item. around the projector. - Do not place inflammables near the - Locations where temperatures may
Краткое содержание страницы № 6
Safety Instructions (Continued) 17. Do not step on the projector or place Ceiling mounting the projector any objects upon it. Besides probable We want you to have a pleasant physical damage to the projector, doing experience using your BenQ projector, so may result in accidents and possible so we need to bring this safety matter injury. to your attention to prevent possible damage to person and property. If you intend to mount your projector on the ceiling, we strongly recommend that y
Краткое содержание страницы № 7
Introduction Projector features The projector integrates high-performance optical engine projection and a user-friendly design to deliver high reliability and ease of use. The projector offers the following features. ® • ECO BLANK - With Philips ImageCare technology, the Eco Blank function will save up to 70% of your lamp power at the same time your image is hiding • 3D function to enjoy the 3D movies, videos, and sporting events in a more realistic way by presenting the depth of the images •
Краткое содержание страницы № 8
Shipping contents Carefully unpack and verify that you have all of the items shown below. If any of these items are missing, please contact your place of purchase. Standard accessories The supplied accessories will be suitable for your region, and may differ from those illustrated. *The warranty card is only supplied in some specific regions. Please consult your dealer for detailed information. Projector Power cord VGA cable Quick start guide User manual CD Warranty card* Remote control wi
Краткое содержание страницы № 9
Projector exterior view 1. External control panel Front/upper side (See "Controls and functions" on page 10 for details.) 1 2. Lamp cover 2 3. Vent (heated air exhaust) 5 4. Quick-release button 5. Focus and Zoom ring 6 6. Vent (cool air intake) 7 7. Speaker grill 3 8. Front IR remote sensor 8 9. Projection lens 9 4 10. AC power jack 11. USB port 12. RGB signal output jack 13. RGB (PC)/Component Video (YPbPr/ YCbCr) signal input jack 14. RS232 control port 15. S-Video input jack Rear/lower sid
Краткое содержание страницы № 10
Controls and functions 8. TEMPerature warning light Projector Lights up red if the projector's temperature becomes too high. 1 8 9. POWER indicator light 2 Lights up or flashes when the projector is 9 under operation. 3 10 10. AUTO 4 11 Automatically determines the best picture 5 12 timings for the displayed image. 6 13 11. Keystone/Arrow keys ( / Up, / 7 14 Down) 11 Manually corrects distorted images resulting from an angled projection. 1. Focus ring Adjusts the focus of the projected image
Краткое содержание страницы № 11
Remote control 9. Keystone/Arrow keys ( / Up, /Down) 8 Manually corrects distorted images 1 9 resulting from an angled projection. 10 2 10. AUTO 11 Automatically determines the best 3 picture timings for the displayed image. 12 4 11. Right 13 5 When the On-Screen Display (OSD) 9 6 menu is activated, the #3, #9, and #11 14 keys are used as directional arrows to 7 select the desired menu items and to 15 make adjustments. 16 12. SOURCE Displays the source selection bar. 13. MODE/ENTER 1. POW
Краткое содержание страницы № 12
Approx. +15º Remote control effective range Infra-Red (IR) remote control sensor is located on the front of the projector. The remote control must be held at an angle within 30 degrees perpendicular to the projector's IR remote control sensor to function correctly. The distance between the remote control and the sensor should not exceed 8 meters (~ 26 feet). Make sure that there are no obstacles between the remote control and the IR sensor on the projector that might obstruct the infra-red b
Краткое содержание страницы № 13
Positioning your projector Choosing a location Your projector is designed to be installed in one of four possible installation locations: 1. Front Table 3. Rear Ceiling Select this location with the projector Select this location with the projector placed on the table in front of the screen. suspended upside-down from the ceiling This is the most common way to position behind the screen. the projector for quick setup and Note that a special rear projection screen portability. and the BenQ P
Краткое содержание страницы № 14
Obtaining a preferred projected image size The distance from the projector lens to the screen, the zoom setting, and the video format each factors in the projected image size. For example, if you are using an 120-inch screen, the recommended projection distance is 4755 mm and the vertical offset is 183 mm. If your measured projection distance is 6.0 m (6000 mm), the closest match in the "Distance from screen (mm)" column is 5943 mm. Looking across this row shows that a 150'' (about 3.8 m) sc
Краткое содержание страницы № 15
Connection When connecting a signal source to the projector, be sure to: 1. Turn all equipment off before making any connections. 2. Use the correct signal cables for each source. 3. Ensure the cables are firmly inserted. • In the connections shown below, some cables may not be included with the projector (see "Shipping contents" on page 8). They are commercially available from electronics stores. • The connection illustrations below are for reference only. The rear connecting jacks available o
Краткое содержание страницы № 16
• If you wish to use this connection method when the projector is in standby mode, make sure the Monitor Out function is turned on in the SYSTEM SETUP: Advanced menu. See "Standby Settings" on page 41 for details. Connecting video source devices You need only connect the projector to a video source device using just one of the connecting methods, however each provides a different level of video quality. The method you choose will most likely depend upon the availability of matching terminals
Краткое содержание страницы № 17
Operation Starting up the projector 1. Plug the power cord into the projector and into a power outlet. Turn on the power outlet switch (where fitted). Check that the POWER indicator light on the projector lights orange after power has been applied. Please use the original accessories (e.g. power cord) only with the device to avoid possible dangers such as electric shock and fire. 2. Press POWER to start the projector. As soon as the lamp lights up, a "Power On Tone" will be heard. The POW
Краткое содержание страницы № 18
Adjusting the projected image Adjusting the projection angle The projector is equipped with 1 quick-release adjuster foot and 1 rear adjuster foot. These adjusters change the image height and projection angle. To adjust the projector: 1. Press the quick-release button and lift the front of the projector. Once the image is positioned where you want it, release the quick-release button to lock the foot in position. 2. Screw the rear adjuster foot to fine-tune the 2 horizontal angle. 1 To ret
Краткое содержание страницы № 19
Correcting keystone Keystoning refers to the situation where the projected image is noticeably wider at either the top or bottom. It occurs when the projector is not perpendicular to the screen. To correct this, you will need to manually correct it following ONE of these steps. • Using the remote control Press / on the projector or remote control to display the Keystone correction page. Press to correct keystoning at the top of the image. Press Press /. Press /. to correct keystoning at t
Краткое содержание страницы № 20
Using the menus The projector is equipped with On-Screen Display (OSD) menus for making various adjustments and settings. The OSD screenshots below are for reference only, and may differ from the actual design. Below is the overview of the OSD menu. Main menu icon DISPLAY Main menu Off Wall Color Auto Aspect Ratio Keystone ENTER Position Status 0 Phase Sub-menu 0 H. Size Digital Zoom 3D Sync Frame Sequential Press MENU/ 3D Sync Invert Disable EXIT to the Teaching Template previous page or to
