Краткое содержание страницы № 1
MX815ST/MX815ST+/MX816ST/
MW817ST
Digital Projector
User Manual
Краткое содержание страницы № 2
Table of contents Direct power off..................................... 34 Important safety Menu operation ...................................... 35 instructions ........................... 3 Maintenance........................ 45 Introduction.......................... 7 Care of the projector............................ 45 Projector features.....................................7 Lamp information ................................... 46 Shipping contents......................................8 Trou
Краткое содержание страницы № 3
Important safety instructions Your projector is designed and tested to meet the latest standards for safety of information technology equipment. However, to ensure safe use of this product, it is important that you follow the instructions mentioned in this manual and marked on the product. Safety Instructions 1. Please read this manual before 5. In some countries, the line voltage is you operate your projector. Save NOT stable. This projector is it for future reference. designed to operate
Краткое содержание страницы № 4
Safety Instructions (Continued) 7. The lamp becomes extremely hot 10. Do not place this product on an during operation. Allow the projector unstable cart, stand, or table. The to cool for approximately 45 minutes product may fall, sustaining serious prior to removing the lamp assembly damage. for replacement. 11. Do not attempt to disassemble this 8. Do not operate lamps beyond the projector. There are dangerous high rated lamp life. Excessive operation of voltages inside which may caus
Краткое содержание страницы № 5
Safety Instructions (Continued) 13. Do not place this projector in any of 14. Do not block the ventilation holes. - Do not place this projector on a the following environments. blanket, bedding or any other soft - Space that is poorly ventilated or surface. confined. Allow at least 50 cm - Do not cover this projector with a cloth clearance from walls and free flow of air or any other item. around the projector. - Do not place inflammables near the - Locations where temperatures may
Краткое содержание страницы № 6
Safety Instructions (Continued) 17. Do not step on the projector or place Ceiling mounting the projector any objects upon it. Besides probable We want you to have a pleasant physical damage to the projector, doing experience using your BenQ projector, so may result in accidents and possible so we need to bring this safety matter injury. to your attention to prevent possible damage to person and property. If you intend to mount your projector on the ceiling, we strongly recommend that y
Краткое содержание страницы № 7
Introduction Projector features The projector integrates high-performance optical engine projection and a user-friendly design to deliver high reliability and ease of use. The projector offers the following features. • Network Settings allowing management of projector status from a computer using a web browser ® • ECO BLANK - With Philips ImageCare technology, the Eco Blank function will save up to 70% of your lamp power at the same time your image is hiding • 3D function to enjoy the 3D movi
Краткое содержание страницы № 8
Shipping contents Carefully unpack and verify that you have all of the items shown below. If any of these items are missing, please contact your place of purchase. Standard accessories The supplied accessories will be suitable for your region, and may differ from those illustrated. *The warranty card is only supplied in some specific regions. Please consult your dealer for detailed information. Projector Power cord VGA cable Quick start guide User manual CD Warranty card* Remote control wi
Краткое содержание страницы № 9
Projector exterior view 1. Lamp cover Front/upper side 2. External control panel 2 (See "Controls and functions" on page 10 for details.) 1 3. Vent (heated air exhaust) 3 4. Quick-release button 5 5. Focus ring 6 6. Vent (cool air intake) 7 4 7. Speaker grill 8. Front IR remote sensor 8 9. Projection lens 9 10. Lens cap 11. AC power jack 10 12. Rear adjuster foot 13. Ceiling mount holes 14. Front adjuster foot 15. RS232 control port 16. RJ45 LAN input jack Rear/lower side 17. USB port 23 24 18.
Краткое содержание страницы № 10
Controls and functions 6. TEMPerature warning light Projector Lights up red if the projector's temperature becomes too high. 1 7. POWER indicator light 6 Lights up or flashes when the projector is 7 under operation. 8. Keystone/Arrow keys ( / Up, / 2 8 Down) 9 3 10 Manually corrects distorted images 4 11 resulting from an angled projection. 12 5 9. Auto 13 Automatically determines the best picture 8 timings for the displayed image. 1. Focus ring Adjusts the focus of the projected image. 10.
Краткое содержание страницы № 11
Remote control 9. Keystone/Arrow keys ( / Up, /Down) 8 Manually corrects distorted images 9 1 resulting from an angled projection. 2 10 10. Auto Automatically determines the best 11 3 picture timings for the displayed image. 4 12 11. Right 5 13 When the On-Screen Display (OSD) 6 9 menu is activated, the #3, #9, and #11 keys are used as directional arrows to 14 7 select the desired menu items and to 15 make adjustments. 16 12. SOURCE Displays the source selection bar. 13. MODE/ENTER 1. POW
Краткое содержание страницы № 12
Approx. +15º Approx. +15º Remote control effective range Infra-Red (IR) remote control sensors are located on the front and back of the projector. The remote control must be held at an angle within 30 degrees perpendicular to the projector's IR remote control sensors to function correctly. The distance between the remote control and the sensors should not exceed 8 meters (~ 26 feet). Make sure that there are no obstacles between the remote control and the IR sensors on the projector that mig
Краткое содержание страницы № 13
Positioning your projector Choosing a location Your projector is designed to be installed in one of four possible installation locations: 1. Front Table 3. Rear Ceiling Select this location with the projector Select this location with the projector placed on the table in front of the screen. suspended upside-down from the ceiling This is the most common way to position behind the screen. the projector for quick setup and Note that a special rear projection screen portability. and the BenQ P
Краткое содержание страницы № 14
Obtaining a preferred projected image size The distance from the projector lens to the screen, the zoom setting, and the video format each factors in the projected image size. Projection dimensions Refer to "Dimensions" on page 54 for the center of lens dimensions of this projector before calculating the appropriate position. MX815ST/MX815ST+/MX816ST (a) Screen Center of lens (c) (b) The screen aspect ratio is 4:3 and the projected picture is 4:3 (a) Screen size (b) Distance from screen (c) Ve
Краткое содержание страницы № 15
MW817ST (a) Screen Center of lens (c) (b) The screen aspect ratio is 16:10 and the projected picture is 16:10 (a) Screen size (b) Distance from screen (c) Vertical offset Diagonal Height Width (mm) (mm) Inches mm (mm) (mm) 80 2032 1077 1723 842 54 100 2540 1346 2154 1053 67 120 3048 1615 2585 1263 81 150 3810 2019 3231 1579 101 180 4572 2423 3877 1895 121 200 5080 2692 4308 2105 135 220 5588 2962 4739 2316 148 240 6096 3231 5169 2526 162 270 6858 3635 5816 2842 182 300 7620 4039 6462 31
Краткое содержание страницы № 16
Connection When connecting a signal source to the projector, be sure to: 1. Turn all equipment off before making any connections. 2. Use the correct signal cables for each source. 3. Ensure the cables are firmly inserted. • In the connections shown below, some cables may not be included with the projector (see "Shipping contents" on page 8). They are commercially available from electronics stores. • The connection illustrations below are for reference only. The rear connecting jacks available o
Краткое содержание страницы № 17
• Many notebooks do not turn on their external video ports when connected to a projector. Usually a key combo like FN + F3 or CRT/LCD key turns the external display on/off. Locate a function key labeled CRT/ LCD or a function key with a monitor symbol on the notebook. Press FN and the labeled function key simultaneously. Refer to your notebook's documentation to find your notebook's key combination. • The D-Sub output only works when an appropriate D-Sub input is made to the COMPUTER 1 jack. •
Краткое содержание страницы № 18
Operation Starting up the projector 1. Plug the power cord into the projector and into a power outlet. Turn on the power outlet switch (where fitted). Check that the POWER indicator light on the projector lights orange after power has been applied. Please use the original accessories (e.g. power cord) only with the device to avoid possible dangers such as electric shock and fire. 2. Press POWER on the projector or ON on the remote control to start the projector. As soon as the lamp light
Краткое содержание страницы № 19
Adjusting the projected image Adjusting the projection angle The projector is equipped with 1 quick-release adjuster foot and 1 rear adjuster foot. These adjusters change the image height and projection angle. To adjust the projector: 1. Press the quick-release button and lift the front of the projector. Once the image is positioned where you want it, release the quick-release button to lock the foot in position. 2. Screw the rear adjuster foot to fine-tune the horizontal angle. 1 2 To ret
Краткое содержание страницы № 20
Correcting keystone Keystoning refers to the situation where the projected image is noticeably wider at either the top or bottom. It occurs when the projector is not perpendicular to the screen. To correct this, you will need to manually correct it following ONE of these steps. • Using the remote control Press / on the projector or remote control to display the Keystone correction page. Press to correct keystoning at the top of the image. Press Press /. Press /. to correct keystoning at t
