Краткое содержание страницы № 1
September 2008
701P49052
8264E Color Wide Format Printer
100kg Unwinder / Winder
User Guide
1
Краткое содержание страницы № 2
Краткое содержание страницы № 3
Table of Contents 1 Safety and Warning Label Information.................................................................. 1 1.1 Safety Considerations...................................................................................... 1 1.2 Warning Labels................................................................................................. 1 1.2.1 Warning Label Locations and Types ............................................................ 2 1.3 Operating Instructions Labels
Краткое содержание страницы № 4
This page has been intentionally left blank. ii 100kg Unwinder / Winder User Guide
Краткое содержание страницы № 5
1 Safety and Warning Label Information 1.1 Safety Considerations Various procedures throughout this user guide may list 2 levels of safety indicators that need to be adhered to during the performance of a procedure. These indicators take into account the level of danger or the size of the potential incidence that can occur while performing a step in a procedure. Below is a list of these indicators and their meaning as they apply to this user guide. Used for a potentially dangerous si
Краткое содержание страницы № 6
1 Safety and Warning Label Information 1.2.1 Warning Label Locations and Types The figures below indicate the locations of the warning labels. 1 1 Figure 1. Front Warning Label Locations 1 1 Figure 2. Rear Warning Label Locations No. Types of warning label 1 2 100kg Unwinder / Winder User Guide
Краткое содержание страницы № 7
1 Safety and Warning Label Information 1.3 Operating Instructions Labels This section explains the different types of operating instructions labels and where they are located. The operating instruction labels are used in this product to briefly explain the operation method for procedures that may require special attention when operating this product. Please ensure you understand the exact locations and the contents of the labels before operating this product. Make sure you can read a
Краткое содержание страницы № 8
1 Safety and Warning Label Information This page has been intentionally left blank. 4 100kg Unwinder / Winder User Guide
Краткое содержание страницы № 9
2 Unwinder / Winder Operation 2.1 Location of Major Components This section will explain the names and functions of the major components of the Unwinder / Winder. 2.1.1 Unwinder Components 3 2 1 1 Figure 4. Location of Major Components (Unwinder) No. Part name Function 1 Unwinder Spindles Feeds paper into the printer. 2 Unwinder Tension Bar Roller Used to guide the paper after printing to the roll-in device. Tension Roller activates the Unwinder Motor to feed paper into the printer
Краткое содержание страницы № 10
2 Unwinder / Winder Operation 2.1.2 Winder Components 4 2 1 3 1 Figure 5. Location of Major Components (Winder) No. Part name Function 1 Winder Spindles Rolls in the media after printing 2 Winder Tension Bar Roller Used to guide the media after printing to the roll-in device. Tension Roller also activates the Winder motor to take up slack in the media. 3 Media Core Used to roll in the media after printing. 4 Unwinder / Winder Control Used to set the operating condition and to displa
Краткое содержание страницы № 11
2 Unwinder / Winder Operation 2.1.3 Unwinder Control Panel The Unwinder Control Panel is used to set the operating mode and to display the status of the Unwinder. 4 5 1 2 3 Figure 6. Unwinder Control Panel 2.1.3.1 Switches / Button No. Part name Function ● OUTSIDE ROLL: Used when using paper rolled in the 1 Automatic outward direction. Operation ● OFF: Feeding device does not operate. Switch ● INSIDE ROLL: Used when using roll paper rolled in the inward direction. ● NORMAL DR
Краткое содержание страницы № 12
2 Unwinder / Winder Operation 2.1.4 Winder Control Panel The Winder Control Panel is used to set the operating mode and to display the status of the Winder. 3 4 1 2 Figure 7. Winder Control Panel 2.1.4.1 Switches No. Part name Function ● OUTSIDE ROLL: Used when the roll paper is rolled in 1 Automatic the outward direction. Operation ● OFF: Roll-in device is not being operated. Switch ● INSIDE ROLL: Used when the roll paper is rolled in the inward direction. ● NORMAL DRIVE: Roll-
Краткое содержание страницы № 13
2 Unwinder / Winder Operation 2.2 Connecting the Power Cable This section describes the procedure for connecting the power cable. DO NOT use a damaged power cable. If the power cable is damaged, contact your local Xerox Customer Service Representative for a replacement. Use the following instructions to install the power cable. 1. Make sure the Unwinder / Winder power switches are set to OFF. 1 Figure 8. Setting Power Switch to OFF No. Part name 1 Power Switch 2. Plug the AC
Краткое содержание страницы № 14
2 Unwinder / Winder Operation 2.3 Turning the Power ON and OFF The following section provides procedures for setting the Unwinder / Winder power ON and OFF. 2.3.1 Turning the Power ON Turn the power ON by following the instructions below. 1. Set the Unwinder / Winder power switch to the ON position. The operation lamp will light. 1 Figure 10. Set the Power Switch to the ON Position No. Part name 1 Unwinder / Winder Power Switch 2.3.2 Turning the Power OFF 1. Ensure that the printer
Краткое содержание страницы № 15
2 Unwinder / Winder Operation 2.4 Loading Roll Media onto the Unwinder The following section describes how to load roll media on the Unwinder. Media core size 3 inch：Maximum media width 1625mm, Minimum media width 1000mm, media outside diameter less than 250mm, weight less than 100kg. Roll media must be loaded in the center of the of printer. 1. Set the Unwinder / Winder Power Switch to ON. 2. Set the Automatic Operation Switch to OFF. Figure 12. Set Unwinder Automatic Operation
Краткое содержание страницы № 16
2 Unwinder / Winder Operation 4. Place the roll media on top of the rear rail. 1 2 Figure 14. Install Roll Media No. Part name 1 Rear Rail 2 Roll Media 5. Set the roll media on the Left Unwinder Spindle and tighten the Left Unwinder Spindle Locking Handle. 3 1 2 Figure 15. Install Roll Media No. Part name 1 Left Unwinder Spindle 2 Roll Media 3 Left Spindle Locking Handle 12 100kg Unwinder / Winder User Guide
Краткое содержание страницы № 17
2 Unwinder / Winder Operation 6. Set the roll media on the Right Unwinder Spindle and tighten the Right Spindle Locking Handle. 3 2 1 Figure 16. Install Roll Media No. Part name 1 Right Unwinder Spindle 2 Roll Media 3 Right Spindle Locking Handle 7. Loosen the Left and Right Unwinder Spindle Locking Handles and move the roll media to the center of the rail so that the media is aligned with the center of the printer. Tighten the Left and Right Unwinder Spindle Locking Handles. 1 2
Краткое содержание страницы № 18
2 Unwinder / Winder Operation 8. Set the Printer Power Switch to ON. After an short initialization period the Printer Control Panel will display “No Media”. 9. Raise the Media Set Lever. The Printer Control Panel will display “Please Set Media”. 1 Figure 18. Install Roll Media No. Part name 1 Media Set Lever 10. Open the Printer Front Cover. 1 Figure 19. Open the Printer Front Cover No. Part name 1 Printer Front Cover 14 100kg Unwinder / Winder User Guide
Краткое содержание страницы № 19
2 Unwinder / Winder Operation 11. Set the Unwinder Automatic Operation Switch as described below: ・ If the paper will be printed on the outside of the roll media: OUTSIDE ROLL ・ If the paper will be printed on the inside of the roll media: INSIDE ROLL Figure 20. Set the Automatic Operation Switch 12. Raise the tension roller located on the rear of the product with your hands. Roll media will automatically be fed out. 2 1 Figure 21. Raise the Tension Roller No. Part name 1 Roll Med
Краткое содержание страницы № 20
2 Unwinder / Winder Operation 13. Insert the roll media into the tension roller, and then into the Rear Printer Platen. Media can be inserted either with the print surface on the outside (Figure 22) or with the print surface on the inside (Figure 23). a. When using roll paper where the print surface is on the outside. 3 3 2 2 1 1 Figure 22. Insert Paper into Tension Roller No. Part name 1 Roll Media 2 Unwinder Tension Bar Roller 3 Rear Printer Platen 16 100kg Unwinder / Winder U
