Краткое содержание страницы № 1
hp LaserJet 9000
9000n•9000dn•9000hns
start
Краткое содержание страницы № 2
Краткое содержание страницы № 3
HP LaserJet 9000, 9000n, 9000dn, and 9000hns printers Start
Краткое содержание страницы № 4
Copyright © Hewlett-Packard Warranty Trademark Credits Company 2001 The information contained in Microsoft, MS Windows, All Rights Reserved. this document is subject to Windows and Windows NT are Reproduction, adaptation, or change without notice. U.S. registered trademarks of translation without prior written Microsoft Corporation. Hewlett-Packard makes no permission is prohibited, except warranty of any kind with All other products mentioned as allowed under the copyright respect to thi
Краткое содержание страницы № 5
Printer Setup Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Installation checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Prepare printer location. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Check package contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Locate printer parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Remove internal packaging. . . . . .
Краткое содержание страницы № 6
Introduction Congratulations on your purchase of the HP LaserJet 9000 Series printer. This series of printers is available in four configurations. HP LaserJet 9000 printer The HP LaserJet 9000 printer (product number C8519A) comes standard with 64 Megabyte (MB) RAM, wide-format printing, and two 500-sheet trays. Note The HP LaserJet 9000 requires an optional enhanced input/ output (EIO) card to connect to a network. HP LaserJet 9000n printer The HP LaserJet 9000n printer (product number C8520
Краткое содержание страницы № 7
Installation checklist This guide will help you set up and install your new printer. For proper installation, please complete each section in order: Unpack the printer steps 1-4 Install the printer steps 5-12 Install printing software step 13 Verify printer setup step 14 WARNING! The printer is heavy. HP recommends that four people move it to avoid injury to you and damage to the printer. ENWW Installation checklist 5
Краткое содержание страницы № 8
368 mm (17.8 in) 633 mm (24.9 in) 600 mm (23.6 in) Step 1 Prepare printer location Printer size Prepare a location for the printer that allows for these physical and environmental requirements: 352.8 mm (13.9 in) 638 mm (25.1 in) 352.8 mm (13.9 in) 638 mm (25.1 in) HP LaserJet 9000 Printer Dimensions (top and side views) 6 Printer Setup ENWW
Краткое содержание страницы № 9
Location requirements for the printer A level area on the floor Adequate power supply (15A, 110V or 220V circuit located near the printer) Space allowance around the printer A stable environment—no abrupt temperature or humidity A well-ventilated room changes No exposure to direct sunlight Relative humidity 20 percent to or chemicals, including 80 percent ammonia-based cleaning solutions Room temperature 50°F to 91° F (10° C to 32.5° C) Printer weight (without print car
Краткое содержание страницы № 10
Step 2 Check package contents power cord face-up output bin printer control panel overlay printer documentation (this manual) print cartridge printer software CD-ROM (including user manual) Package contents 8 Printer Setup ENWW
Краткое содержание страницы № 11
Step 3 Locate printer parts The following illustrations give the location and names of the important printer parts. E A B F C D G I J H K L M Printer parts (front and rear views) A Face-up bin F Front door J Foreign interface harness (AUX) B Control panel G Tray 3 K HP Fast InfraRed (FIR) C Tray 2 H EIO slots (3) Connect D Power switch I Parallel cable L HP Jet-Link connector connector E Standard output bin M Power cord connector (Face-down bin) ENWW Locate printer parts 9
Краткое содержание страницы № 12
Step 4 Remove internal packaging Remove all packaging from the printer. WARNING! This printer weighs approximately 63.5 kg (140 lb). HP recommends that four people move it to avoid injury to you and damage to the printer. To remove internal packaging 1 Remove all orange packing material from the exterior of the printer and remove any cardboard or styrofoam material that is not orange. 2 Remove all orange packing material from the standard output bin and the protective film from the display.
Краткое содержание страницы № 13
Step 5 Install accessories Install any paper-handling accessories that you purchased with the printer or separately. Use the installation instructions that are packaged with the accessories. If you have a 3,000-sheet stapler/stacker (or stacker) and a duplexer, Tray 4, or both, install the duplexer and Tray 4 before trying to install the 3,000 sheet stapler/stacker (or stacker). HP Fast InfraRed Connect 3,000-sheet stapler/stacker 3,000-sheet stacker Tray 4 (2,000- Duplex printing sheet i
Краткое содержание страницы № 14
Step 6 Install print cartridge Use this procedure to install the print cartridge. If toner gets on your clothing, wipe it off with a dry cloth and wash the clothing in cold water. Hot water sets toner into fabric. To install the print cartridge 1 1 Before removing the print cartridge from its packaging, set the print cartridge on a sturdy surface. Gently slide the print cartridge out of the packaging. CAUTION To prevent damage to the print cartridge, 2 use two hands when removing it from
Краткое содержание страницы № 15
5 Press the button on the green lever, 5 and turn the lever clockwise to the locked position. 6 Close the front door. 6 ENWW Install print cartridge 13
Краткое содержание страницы № 16
Step 7 Load Trays 2 and 3 This section describes how to load A4- 1 or letter-size paper. For instructions on loading and configuring other sizes and types of media, see the HP LaserJet 9000 Introduce manual (user guide) that came on the CD-ROM. CAUTION To avoid a paper jam, never open a tray while the printer is printing from that tray. 2 To load Tray 2 and Tray 3 1 Pull the tray open until it stops. 2 Load a stack of Letter- or A4-size paper with the top of the stack toward the rear of
Краткое содержание страницы № 17
4 Adjust the front (X) paper guide by 4 pressing the tab on the guide and sliding it to the mark for A4- or letter- size paper. 5 Close the tray until it stops. 6 Repeat steps 1 through 6 to load the other tray. 5 ENWW Load Trays 2 and 3 15
Краткое содержание страницы № 18
Step 8 Connect printer cables The printer can connect to a computer using a parallel cable, or to the network using an optional HP Jetdirect print server. Connection to a Token Ring network is available through an optional Token Ring card. For printers equipped with an optional HP Jetdirect print server, a twisted-pair network cable connection is provided through a 10/100Base-TX (RJ-45) connector. The printer also has a connector for HP Fast InfraRed Connect, a Foreign Interface Harness, an
Краткое содержание страницы № 19
Connecting a parallel cable Use a parallel cable if you want to connect the printer directly to a computer. To ensure reliability, use an IEEE-1284 bidirectional C-type parallel cable. These cables are clearly marked with “IEEE-1284.” Only IEEE- 1284 cables support all of the advanced printer features. To connect a parallel cable 1 1 Make sure the printer and the computer power are turned off. 2 Connect the parallel cable to the printer parallel port. Press the locking release levers while
Краткое содержание страницы № 20
Connecting to Ethernet 10/100Base-TX network Use the RJ-45 connector if you want to connect the printer to an Ethernet 10/100Base-TX network. The HP Jetdirect print server is an optional accessory for the base model and standard on the n, dn, and hns models. HP Jetdirect print servers are available for many different network connections. To connect to Ethernet 10/ 1 100Base-TX network 1 Locate the power switch on the front of the printer. Press the power switch to turn the printer off (o
