Краткое содержание страницы № 1
HP JetDirect Print Servers
HP JetDirect 400N
Hardware Installation Guide
For HP Printers with MIO Slots
Краткое содержание страницы № 2
Краткое содержание страницы № 3
Hardware Installation Guide HP JetDirect 400N Print Server
Краткое содержание страницы № 4
© Copyright A copy of the specific warranty terms Hewlett-Packard Company, 2000. applicable to your Hewlett-Packard All Rights Reserved. product and replacement parts can be obtained from your HP Sales and Service Reproduction, adaptation or translation Office or authorized dealer. without prior written permission is Safety Considerations prohibited, except as allowed under the copyright laws. Prior to the installation and use of this product, review all safety markings and Publication
Краткое содержание страницы № 5
HP JetDirect Print Servers HP J4100A for Fast Ethernet 10/100TX Link Jumpers (see Appendix B) and IEEE 802.3u (10/ 100Base-TX, 10Base2) networks. An RJ-45 connector supports 10/100 Mbps network connections using unshielded twisted-pair cable. (For 100Base-TX networks, use Category 5 cable.) The BNC connector supports 10 Mbps HP J4100A operation through thin coaxial cables. Token Ring Data-Rate Switch HP J4105A for Token Ring (IEEE 802.5) networks and can be configured for 4 or 16 M
Краткое содержание страницы № 6
Quick Installation NOTE See chapter 2 for detailed information. 1. If you have a Token Ring card, Set the network Data-Rate switch to 16 Mbps (default) Token Ring data-rate switch or 4 Mbps depending on your network. If you don't know the 4 Mbps network data rate, ask your network administrator. 16 Mbps 2. Before installing the card, verify that your printer works. Print a test page or configuration plot. For instructions, see chapter 2 or refer to your printer manuals. 3. Turn off your
Краткое содержание страницы № 7
4. Verify that the card was installed correctly. Location of "I/O CARD READY" message on test page Print another test page (or configuration plot) and verify that the “I/O CARD READY” message appears. On the test page, the location of the “I/O CARD READY” message depends on your printer model. NOTE If other messages appear, see the troubleshooting sections of the HP JetDirect Print Server Administrators Guide. For HP J4100A (10/100Base-TX), see appendix B in this manual for special tro
Краткое содержание страницы № 8
6 Quick Installation
Краткое содержание страницы № 9
Contents Contents Quick Installation 1 The HP JetDirect Print Server Card Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 The HP JetDirect Print Server Cards at a Glance . . . . . . . 1-2 Supported Networks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 What You Need for Installation . . . . . . . . . . . . . . . . . . . . . . 1-4 2 Installing the HP JetDirect Print Server Card Task 1. If you have a Token Ring card, set the Dat
Краткое содержание страницы № 10
4 Using the Control Panel To Configure HP JetDirect Cards in Large-Format Printers Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1 Supported Network Protocols . . . . . . . . . . . . . . . . . . . . . . . . 4-2 Configuring Novell NetWare Frame Types . . . . . . . . . . . . . 4-6 Configuring TCP/IP Parameters . . . . . . . . . . . . . . . . . . . . . 4-9 Configuring Apple EtherTalk Phase Parameters (Ethernet Cards Only) . . . . . . . . . . . . . . .
Краткое содержание страницы № 11
Introduction 1 1 The HP JetDirect Print Server Card Introduction The HP JetDirect print server is a card that is installed in the modular input/output (MIO) slot of a printer and allows the printer to be connected directly to a network instead of a single PC. When you use an HP JetDirect print server, you can place your printer anywhere on a network for use by multiple clients. The HP JetDirect print server card must first be installed into the printer and then be configured for network ope
Краткое содержание страницы № 12
The HP JetDirect Print Server Cards at a Glance Network Network Types Connections Supported Ethernet, RJ-45 (unshielded IEEE 802.3 twisted-pair cable), (10/100Base- BNC (thin Ethernet J4100A TX, 10Base2) coaxial cable) Network Network Types Connections Supported Token Ring, RJ-45 (unshielded IEEE 802.5 twisted-pair cable), (4 or 16 Mbps) DB 9 (type 1, 2 or 6 J4105A shielded twisted- pair cable) Network Network Types Connections Supported Ethernet, RJ-45 (unshielded IEEE 802.3 twist
Краткое содержание страницы № 13
Introduction 1 Supported Networks Supported Network Applicable 1 Protocols Supported Networks Products IPX/SPX and Novell NetWare J4100A compatible Microsoft Windows 95/98/NT/2000 J4105A J4106A EtherTalk AppleTalk J4100A J4106A DLC/LLC Microsoft Windows NT J4100A 2 Artisoft LANtastic J4105A J4106A TCP/IP Microsoft Windows 95/98/NT/2000 J4100A Novell NetWare 5 via NDPS J4105A LPD J4106A UNIX, including: Hewlett-Packard HP-UX, Sun Microsystems Solaris (Sun SPARCsystems only), Linux 2 2 2 SCO U
Краткое содержание страницы № 14
What You Need for Installation The appropriate HP JetDirect print server, documentation, and software. A static-safe environment for handling the card. A grounding wrist strap or similar device is recommended. Appropriate network cables and connectors for connecting the card to the network. A small flat-blade screwdriver. Installing the card into the upper MIO slot of an HP LaserJet 4Si/4Si MX printer also requires a small Phillips-head screwdriver. CAUTION The HP JetDirect card co
Краткое содержание страницы № 15
Installation 2 2 Installing the HP JetDirect Print Server Card Task 1. If you have a Token Ring card, set the Data-Rate switch (if necessary) Before installing a Token Ring card, you must set the data-rate switch to either 4 Mbit/second or 16 Mbit/second (factory default). The selected setting depends on the data-rate operation of your Token Ring network. 1. Locate the Data-Rate switch on the Token Ring print server card. 2. Set the switch to 4 Mbit/s or 16 Mbit/s. Note: when switches are
Краткое содержание страницы № 16
Task 2. Before installing the card, verify the printer works The following pages show instructions for printing a self-test page or configuration plot to verify the printer is operating correctly. Locate and follow the instructions for your specific printer. If a self-test page or configuration plot does not print, see your printer manuals for troubleshooting procedures. HP LaserJet 5, 5M, and 5N printers 1. Turn on the printer. 2. Press [Menu] repeatedly until TEST MENU appears. 3. Press
Краткое содержание страницы № 17
Installation 2 HP LaserJet 5Si, 5Si MX, 5Si NX, 5Si Mopier printers 1. Turn on the printer and wait until a ready message is displayed. 2. Press [Menus] repeatedly until TEST MENU appears. 3. Press [Items] until PCL CONFIGURATION PAGE appears. 4. Press [Select*] to print the PCL configuration page. Control Panel for the HP LaserJet 5Si Series printers Installing the HP JetDirect Print Server Card 2-3
Краткое содержание страницы № 18
HP Color LaserJet and Color LaserJet 5, 5M printers 1. Turn on the printer and wait until a ready message is displayed. 2. Switch the printer offline by pressing [On Line] to turn off the On Line light. 3. Press [Menu] repeatedly until the following appears: PCL TEST MENU PCL SELF TEST 4. Press [Enter]. A self-test page will print. . Control Panel for HP Color LaserJet and Color LaserJet 5/5M 2-4 Installing the HP JetDirect Print Server Card
Краткое содержание страницы № 19
Installation 2 HP LaserJet 4, 4M, 4 Plus, and 4M Plus printers 1. Turn on the printer and wait until the Ready light is lit. 2. Switch the printer offline by pressing [On Line] to turn off the On Line light. 3. Press [Menu] repeatedly until TEST MENU appears. 4. Press [Item] repeatedly until SELF TEST appears. 5. Press [Enter]. A self-test page will print. 05 SELF TEST Control Panel for HP LaserJet 4, 4M, 4 Plus, and 4M Plus Installing the HP JetDirect Print Server Card 2-5
Краткое содержание страницы № 20
HP LaserJet 4Si and 4Si MX printers 1. Turn on the printer and wait until the Ready light is lit. 2. Switch the printer offline by pressing [On Line] to turn off the On Line light. 3. Press [Menu] repeatedly until TEST MENU appears. 4. Press [Item] repeatedly until SELF TEST appears. 5. Press [Enter]. A self-test page will print. 05 SELF TEST Control Panel for HP LaserJet 4Si and 4Si MX 2-6 Installing the HP JetDirect Print Server Card
