Краткое содержание страницы № 1
CP60 Printer Guide
558871-201 Rev. E
July 2005
11111 Bren Road West
Dealer information:
Minnetonka, MN 55343-9015
952.933.1223
952.933.7971 FAX
Datacard is a registered trademark of DataCard Corporation.
July 2005 558871-201 Rev. A
Краткое содержание страницы № 2
Information resources for the CP60 Card Printer CP60 Quick The Quick Install Guide, packed at the top of the printer Install Guide carton, shows you the steps to install the printer. For detailed installation information, see e-Guide/ InfoCent.chm on the driver CD-ROM. CP60 Printer The Printer Guide (this document) contains operating Guide information for the printer. It also tells you how install the printer. Info Central For in-depth information about using the printer, install Info Cen
Краткое содержание страницы № 3
About the printer . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Set up the network printer . . . . . . . . . . . . . . .30 The outside of the printer . . . . . . . . . . . . . . . . 1 Set the Data Format. . . . . . . . . . . . . . . . . . . .34 The inside of the printer. . . . . . . . . . . . . . . . . . 3 Set up for your card design . . . . . . . . . . . . . .35 Features and options. . . . . . . . . . . . . . . . . . . . 3 SNMP Support . . . . . . . . . . . . . . . . . . . . . . . .36
Краткое содержание страницы № 4
Page iv Set LCD Backlighting . . . . . . . . . . . . . . . 53 SY-01310 Flash Error . . . . . . . . . . . . . . 73 Set the Data Format. . . . . . . . . . . . . . . . 54 SY-01312 Flash error . . . . . . . . . . . . . . 74 Set the Address Mode . . . . . . . . . . . . . . 55 SY-01314 Flash Error . . . . . . . . . . . . . . 75 Set the IP Address, Subnet Mask, SY-01317 Memory Error . . . . . . . . . . . . 76 and Gateway Address. . . . . . . . . . . 57 SY-01325 Data Error . . . . . . . . . . . . . . .
Краткое содержание страницы № 5
MS-01425 Mag Stripe Error . . . . . . . . . . 91 PR-01721 EEPROM Error. . . . . . . . . . 106 MS-01426 EEPROM Error . . . . . . . . . . . 92 PR-01723 Hardware Error. . . . . . . . . . 107 MS-01427 or MS-01428 Mag PR-01724 Ribbon Break . . . . . . . . . . . 109 Stripe Error . . . . . . . . . . . . . . . . . . . 93 PR-01726 Ribbon Out . . . . . . . . . . . . . 111 MS-01429 Mag Stripe Data . . . . . . . . . . 94 PR-01730 Printhead Error . . . . . . . . . . 112 MS-01430 Mag Stripe Error . . . . . .
Краткое содержание страницы № 6
Page 1 About the printer This guide applies to CP60 Card Printer. The information also applies to the SP60 Card Printer. The printers include the Built-in Ethernet feature and can include the Open Card option. The outside of the printer Duplex Module: Optional module at the back of the printer that turns the card to print the other side. Printer Cover. Latch: Lift the latch to open the printer cover. Input Hopper: Open the cover to load blank cards. LCD Panel: Shows the printer status and any
Краткое содержание страницы № 7
Ports are located on the left side of the printer. Network Port: Use the Ethernet port to connect a printer with the Built-in Ethernet feature. USB Data Port: Connect the data cable to the printer. ALL printers have this port. Manual Advance Knob: Use to move a card in the printer or to turn rollers. Power Receptacle: Plug in the power supply to power on the printer. Security Lock Receptacle: Connect the optional security lock to the opening under the ledge of the printer (not visible
Краткое содержание страницы № 8
Page 3 The inside of the printer Cover Arm: Holds the cover and printhead cartridge in place. Printhead Cartridge: Applies the image to the card. The label includes”YMC” for color or “K” for monochrome printheads. Print Ribbon Cartridge (shown with color print ribbon). Printer Label: Includes the serial number and model information (located on the left side of the printer and not visible in this drawing). Cleaning Roller (not visible in this drawing): Removes dust and debris from cards. Fea
Краткое содержание страницы № 9
• Printers with “U” printing can print one color (monochrome) only. “C” printing is full-color or monochrome (with specific ribbons). • All CP60 printers have a USB data connection. They also have one of the following: — Built-in Ethernet (Net) connection — Open Card (OC) data format and Built-in Ethernet • Printers can include a duplex (2) module. •A magnetic stripe module can be a three-track (IAT) module. • Printers can have a 100-card (H1) or 200-card (H2) input hopper. The input hopp
Краткое содержание страницы № 10
Page 5 Loading cards 1 Open the input hopper cover. 2 Remove cards from the original package. Tips: Handling cards • Cards can stick together: Slide or fan cards to separate the edges. • Do not touch the surface of cards before printing them. (Oils on hands will reduce printing quality.) • Handle cards by the edges or wear gloves. • Orient all cards the same way.
Краткое содержание страницы № 11
3 Place the cards in the input hopper. The diagram shows the typical locations for the magnetic stripe and smart card chip. 4 Push the input hopper cover closed until it latches. Magnetic stripe Smart card chip See Info Central for current information about cards to use in the printer. Page 6
Краткое содержание страницы № 12
Page 7 Loading print ribbon 1 Open the printer cover. 2 Remove the ribbon cartridge. 3 Remove both used ribbon spools from the cartridge (if present). Tips: Handling print ribbon • Keep unused ribbon in the original package. • Don’t place ribbon on a dusty or dirty surface–dirt could damage the printhead. 4 Run a cleaning card and replace the cleaning sleeve at the same time that you load a new print ribbon. See "Cleaning the printer" on page 39 for the steps to follow.
Краткое содержание страницы № 13
5 Load the new roll of print ribbon on the cartridge. — Put the full spool of ribbon on the supply spindle of the ribbon cartridge. Push until the spool clicks onto the spindle. — Put the empty take-up spool on the spindle with the solid black gear. Push until the spool clicks onto the spindle. 6 Replace the loaded ribbon cartridge in the printer. — Make sure both spindles rest in the black supports on the left side of the printer. — Make sure the ribbon cartridge handle rests in the suppo
Краткое содержание страницы № 14
Page 9 Power on the printer Plug in the printer to power it on. The printer does not have a power switch. 1 Make sure the power supply cord connects to the printer power receptacle (1). 2 Connect the power cord to the power supply (2). 3 Connect the power cord to the power outlet (3). 4 The printer powers on and the Status Light is amber. 5 When the printer is ready to print cards, the Status Light displays steady green. The printer must be connected to a computer (locally or through a netw
Краткое содержание страницы № 15
The LCD panel The CP60 Card Printer with built-in Ethernet includes an LCD panel. The LCD panel has a 2-line display, four keys, and the Status light. This section describes what you need to know when printing cards. See "Printer LCD settings" on page 45 for detailed information about viewing and changing network settings. The LCD panel provides the following: • Current State (line 1): Shows whether the printer is ready to print, is busy, or is paused. — Press the Ready key to pause or res
Краткое содержание страницы № 16
Page 11 — See "Printer messages" on page 65 for details about messages. • Status: Information about the printer, including printer card counts and network settings. To view status details: — Press the Enter key to move to the Main Menu. — Press the Enter key again to enter the Status Menu. — Press the Up Arrow or Down Arrow key to scroll through the Status Menu choices. — Press the Enter key to view the data.
Краткое содержание страницы № 17
— Press the Enter key again to return to the menu. — Scroll to “Exit” and press the Enter key to leave a choice. Repeat as needed to leave the menus. See "Printer LCD settings" on page 45 for details about viewing and changing settings. Page 12
Краткое содержание страницы № 18
Page 13 Make a printer test card 1 Power off the printer. 2 Confirm that cards and print ribbon are loaded in the printer. — If the printer has a magnetic stripe module, the card for a printer test card must have a magnetic stripe. — If it is a three-track module, be sure to use blank cards with the correct coercivity (the default is high coercivity cards, which are shipped in the Starter Kit.) — If the printer has been installed previously and has used a custom magnetic stripe format,
Краткое содержание страницы № 19
5 After it is printed, remove the card from the output hopper. Tips for success • Allow 30 to 60 seconds for the printer to begin printing the test card. • The status light will flash green while the printer is processing the data. • If the status light is steady amber and the printer beeps, the printer is paused. Press the Ready key once to un-pause the printer. • If the printer test card did not print successfully, try the procedure again, making sure you follow the instructions. If the te
Краткое содержание страницы № 20
Page 15 Data formats for the CP60 Card Printer All CP60 printers are shipped with the CP Driver CD-ROM, and can print cards sent by the CP Driver (when the Data Format is set to CP Driver). The printer can also be purchased with the Open Card option. Printers with the Open Card option can also print cards using the Open Card data format (when the Data Format is set to Open Card). This section describes the requirements and functionality of each format.
