Руководство по эксплуатации Antec Performance TX640B

Краткое содержание страницы № 1

USER’S MANUAL
Performance TX635 / TX640B
User's Manual

Краткое содержание страницы № 2

At Antec, we continually refine and improve our products to ensure the highest quality. So it's possible that your new case may differ slightly from the descriptions in this manual. This isn't a problem; it's simply an improvement. As of the date of publication, all features, descriptions, and illustrations in this manual are correct. Disclaimer This manual is intended only as a guide for Antec's Computer Enclosures. For more comprehensive instructions on installing your motherboard and peripher

Краткое содержание страницы № 3

3. Line up your motherboard with the standoff holes, and remember which holes are lined up. Not all motherboards will match with all the provided holes; this is normal, and won't affect functionally. (In other words, there will likely be extra holes.) 4. Remove your motherboard by lifting it up. 5. Screw the brass standoffs into the threaded holes that line up with your motherboard. Do not overtighten the standoffs. Some standoffs may be pre-installed for your convenience. 6. Place your mother

Краткое содержание страницы № 4

Motherboard Pin Layout 1 2 Pin Signal Names Pin Signal Names USB Power 1 2 USB Power 2 1 3 Negative Signal 1 4 Negative Signal 2 5 Positive Signal 1 6 Positive Signal 2 7 Ground 1 8 Ground 2 9 Key (No Pin) 10 Empty Pin 9 10 CONNECTING THE IEEE 1394 (FIREWIRE®, i.LINK®) PORT You will find a single 10-pin connector on a cable attached to the front IEEE 1394 connection. This is an Intel standard connector, which is keyed so that it can’t be accidentally reversed as long as it is connected to a prop

Краткое содержание страницы № 5

6. Rear Right Speaker Out Pin: Connect the RET-R connector to this pin. 7. Rear Left Speaker Out Pin: Connect RET-L connector to this pin. 3.5" DEVICE INSTALLATION With the front bezel facing you, swing the front door out. You can see there are three 5.25" and two 3.5" external drive bays. Inside the case there are four 3.5" drive cages. 1. On the sides of the front bezel there are two tabs. Press the tabs to remove the top half of the bezel. 2. Unscrew the two thumbscrews located on the drive b

Краткое содержание страницы № 6

Specifications: Size: 120 x 120 x 25.4 mm Rated Voltage: DC 12V Input Static Acoustical Input Speed Air Flow Current Pressure Noise Power High 0.24A 2.24 m³/min. 2.54 mm-H2O 30 dBA 2.9 W 2000 RPM (Max.) (79 CFM) (0.10 inch-H2O) Medium 1.59 m³/min. 1.53 mm-H2O 0.2A 28 dBA 2.4 W 1600 RPM (56 CFM) (0.06 inch-H2O) Low 1.1 m³/min. 0.92 mm-H2O 0.13A 1.6 W 25 dBA 1200 RPM (39 CFM) (0.04 inch-H2O) This case comes with two 80mm front fan mounts, one 80mm side panel fan mount for the VGA card and one 92mm

Краткое содержание страницы № 7

Note: Lower the guide down as low as possible without touching the CPU cooler. This is the most common way to cool a CPU that comes with a stock cooler. Performance Mode If you are a high performance user and you need extra cooling for your CPU. 1. Remove the side panel from the case. 2. Install a 92 mm fan to the fan hood so that the air is blowing down on the CPU cooler. 3. Lower the lower air guide with fan down to the CPU cooler. This will bring more cool air to the CPU cooler and enhance CP

Краткое содержание страницы № 8

Antec, Inc. 47900 Fremont Blvd. Fremont, CA 94538 Tel: 510-770-1200 Fax: 510-770-1288 Antec Europe B.V. Sydneystraat 33 3047 BP Rotterdam The Netherlands Tel: +31 (0) 10 462-2060 Fax: +31 (0) 10 437-1752 Technical Support US & Canada 1-800-22ANTEC CustomerSupport@antec.com Europe +31 (0) 10 462-2060 europe.techsupport@antec.com www.antec.com © Copyright 2005 Antec, Inc. All rights reserved. All trademarks are the property of their respective owners. Reproduction in whole or in part without writt