Краткое содержание страницы № 1
WS-7025U
Wireless 433 MHz
Radio-controlled Weather Station
Instruction Manual
Краткое содержание страницы № 2
2
Краткое содержание страницы № 3
Topic Page Inventory of Contents/Additional Equipment 4 About WWVB 4-5 Quick Set-Up Guide 5 Detailed Set-Up Guide Battery Installation 5-6 Program Mode Function Keys 7 12/24 Hour Time Setting 7 Time Zone Setting 7-8 Daylight Saving Time Setting 8 Time Setting (WWVB & Manual) 9-10 Setting Day, Date and Year 10-11 11 Selecting °F or °C Setting the LCD Contrast 11-12 Features Back Light 12 Weather Forecast 12-13 Indoor Temperature, Humidity & C
Краткое содержание страницы № 4
INVENTORY OF CONTENTS 1. The Weather Station (Figure 1). 2. One TX3U Remote Control Sender with mounting bracket (Figure 2). 3. Three each, ½” Philips screws. 4. One strip double-sided adhesive tape. 5. Instruction Manual and Warranty Card. Time LCD Figure 2 Date LCD Forecast LCD Mounting Bracket Indoor LCD Outdoor LCD Holder Figure 1 ADDITIONAL EQUIPMENT (not included) 1. Two fresh AA 1.5V batteries. 2. Two fresh AAA 1.5V batteries. 3. One Phi
Краткое содержание страницы № 5
continually measuring every second, of every day, to an accuracy of ten billionths of a second per day. These physicists have created an international standard measuring a second as 9,192,631,770 vibrations of a Cesium-133 atom in a vacuum. QUICK SET-UP GUIDE 1. Insert two AAA batteries into the Remote Control Sender. 2. Insert two AA batteries into the WEATHER STATION. 3. Wait 5 minutes, or until the outdoor temperature is displayed in the OUTDOOR LCD (Liquid Crystal Display). 4
Краткое содержание страницы № 6
to fall away from the unit. Place the screw partially back into its hole and angle it slightly—so the threads grab the battery cover. With the screw, pull the battery cover off. 3. Observing the correct polarity install 2 AAA batteries. The batteries will fit tightly (to avoid start-up problems make sure they do not spring free). 4. Check the LCD screen of the Remote Control Sender to see if there is a temperature reading. If there is no reading, check the polarity of the batteries o
Краткое содержание страницы № 7
PROGRAM MODE If 30 seconds are allowed to pass or either the IN or Programming Note: the OUT button is pressed during programming modes, the unit will set the last information entered—the display will stop flashing and return to normal time-date readings. If you don’t leave the program mode during the programming of sections III through VIII, you can advance to step 3 of the next program setting. If you do leave the program setting (or want to program a specific setting) follow each i
Краткое содержание страницы № 8
the top of the TIME LCD. Observe the chart below, showing the corresponding abbreviations, time zones, and codes. TIME ZONES GMT 0 Atlantic -4 EST; Eastern -5 CST; Central -6 MST; Mountain -7 PST; Pacific -8 ALA; Alaska -9 HAW; Hawaii -10 Note: There are more time zones represented by numbers than there are represented by 3 letter abbreviations. If you live in North America you need only be concerned with the ones in the chart above. 4. Press the SET button to confirm and
Краткое содержание страницы № 9
V. TIME There are two methods by which the time can be set: A) Automatically via WWVB reception or B) Manually. A. WWVB (Remote Control Time) This method requires you to do nothing except wait for the signal to be received and to select a time zone. Reception usually takes approximately 6-10 minutes during optimal conditions. The best conditions for reception is at night, between midnight and 6:00 AM—when there is less atmospheric interference. To keep your time as accura
Краткое содержание страницы № 10
6. Press the SET button to confirm the minutes and to advance to the Day, Date, and Year setting mode. Note: In 12h mode, “PM” will appear to the left of the time during PM hours. If the time is not within the PM hours, nothing will be displayed. Be sure to set the time to the correct AM/PM time to ensure automatic reception at optimal times. VI. SETTING THE DAY, DATE, AND YEAR 1. Press and hold the SET button for 3 seconds, or until “12 h” or “24 h” flashes in the DATE LCD.
Краткое содержание страницы № 11
10. Press the SET button to confirm and to advance to the °F or °C setting mode. VII. SELECTING °F OR °C 1. Press and hold the SET button for 3 seconds, or until “12h” or “24h” flashes in the DATE LCD. 2. Press the SET button 9 times to reach the °F or °C setting mode. 3. “°F” is the default setting, and should be flashing in the DATE LCD. 4. Press the CH button to shift °F to °C and back. 5. Press the SET button to confirm your selection and to advance to the LCD contrast sett
Краткое содержание страницы № 12
FEATURES OF THE WS-7025U WWVB Tower Icon (indicates time reception) Alarm icon Weather Tendency Arrow Forecast icon Comfort Level Indicator Satellite icon (indicates outdoor transmission) I. BACK LIGHT The WS-7026U has a backlight that can be activated by pressing any of the eight function buttons. After a button has been pressed the backlight will come on for five seconds before automatically shutting off. II. WEATHER FORECAST The weather forecasting feature is est
Краткое содержание страницы № 13
A. WEATHER ICONS There are 3 possible weather icons that will be displayed in the FORECAST LCD: Sunny—indicates that the weather is expected to improve (not that the weather will be sunny). Sun with Clouds—indicates that the weather is expected to be fair (not that the weather will be sunny with clouds). Clouds with Rain—indicates that the weather is expected to get worse (not that the weather will be rainy). The weather icons change when the unit detects a change in air pre
Краткое содержание страницы № 14
III. INDOOR TEMPERATURE, HUMIDITY, AND COMFORT LEVEL INDICATOR The current Indoor Temperature (viewed on the left) and Relative Humidity (viewed on the right) are displayed in the INDOOR LCD. The Comfort Level Indicator is located at the center of the INDOOR LCD. The indicator will display a happy face icon when the temperature is between 68°F and 79°F (20°C and 25.9°C) and the humidity is between 45% and 64%. A sad face icon will be displayed when the temperature and humidity are o
Краткое содержание страницы № 15
3. While “MAX” is still displayed press the IN button again to return to the current data display. By waiting 20 seconds during either the minimum or the maximum readings the unit will automatically return to current data readings. B. VIEWING THE OUTDOOR TEMPERATURE RECORDS 1. Press the OUT button once. “MIN” appears in the upper- center location of the flashing OUTDOOR LCD, indicating that the minimum temperature and the time and date of occurrence are displayed. The minimum reco
Краткое содержание страницы № 16
1. Press and hold the AL1 button for 5 seconds or until the alarm-time display flashes in the DATE LCD. 2. Press the IN button to set the alarm hours and the OUT button to set the alarm minutes. 3. Press the AL1 button or wait 15 seconds for the unit to automatically confirm the alarm time and return to display the date in the DATE LCD as normal. 4. The ((1)) icon, appearing in the DATE LCD, indicates that the alarm is set to sound at the programmed time. 5. Programming the alarm time
Краткое содержание страницы № 17
up of Remote Control Sender units with the WS-7025U. These extra sensors can be purchased through the same dealer as this unit, or by contacting La Crosse Technology directly. A TX3U will monitor temperature only and the TX3UP will monitor the temperature via a probe for use in pools, spas, etc. Note: When setting up multiple units it is important to remove the batteries from all existing units in operation. Then insert batteries into all the Remote Control Sender units in numeric se
Краткое содержание страницы № 18
the button twice) will display the same data for the maximum recordings. 3. To reset the Minimum/Maximum readings, it is necessary to select which Remote Control Sender you wish to reset. Press and hold the OUT button for 5 seconds, the records for the selected Remote Control Sender unit will be reset. 18
Краткое содержание страницы № 19
MOUNTING Before permanently mounting ensure that the Indoor Temperature Note: Station is able to receive WWVB signals from the desired location. Also, extreme and sudden changes in temperature will decrease the accuracy of the weather station and changes in elevation will result with inaccurate weather forecasting for the next 12 to 24 hours. These changes will require a 12 to 24 hour wait before obtaining reliable data. To achieve a true temperature reading, avoid mounting where di
Краткое содержание страницы № 20
1) With a nonabrasive solution, clean and dry the back of the mounting bracket and the mounting surface to ensure a secure hold. The mounting surface should be smooth and flat. 2) Remove the protective strip from one side of the tape. Adhere the tape to the designated area on the back of the mounting bracket. 3) Remove the protective strip from the other side of the tape. Position the Remote Control Sender in the desired location, ensuring that the Indoor Temperature Station can r
