Руководство по эксплуатации American Standard BERWICK 7430.801

Краткое содержание страницы № 1

Installation
Instructions
™ ™
BERWICK / BOULEVARD 7430.801
SPREAD LAVATORY FAUCET
7430.821
with Speed Connect™ Drain
7431.801
7430.821
7431.821
7431.821
Congratulations on purchasing your American Standard
7430.801
faucet with Speed Connect drain, a feature found only on
7431.801
American Standard faucets.
Certified to comply with ANSI A112.18.1
Speed Connect Drain*
M968640 REV.1.1
• Fewer parts, installs in less time
• Never needs adjustment
• Guaranteed to seal properly the first time, every

Краткое содержание страницы № 2

VALVE INSTALLATION 2 Place RUBBER RING (9) into DECK ADAPTER (10). Install LOCKNUT (11) and RUBBER WASHER (12) onto VALVE BODY (13). From under side of mounting surface, install VALVE BODY (13) through valve mounting holes. Threads of VALVE BODY (13) should extent at least 5/16 of a inch above mounting surface top. Fig. A. Thread DECK ADAPTER (10) onto VALVE BODY (13) until snug against internal stop. If necessary, adjust LOCKNUT (11). 1 10 10 9 9 MOUNTING 5/16'' MIN. SURFACE 13 12 Fig. A. 12 11

Краткое содержание страницы № 3

POP-UP DRAIN 5 Fig. A. Fig. B. Remove CLEAR PLASTIC COVER (1). 1 Remove CARDBOARD SPACER (2) from under DRAIN DRAIN POP-UP (3). 3 BODY Tighten TAILPIECE (4) on DRAIN BODY before installing DRAIN BODY. Fig. B. 2 4 REMOVE FLANGE 6 Fig. A. Fig. B. 1 Thread FLANGE (1) counter-clockwise and remove FLANGE (1) and FOAM GASKET (2) from drain body. Fig. A. Thread LOCKNUT (3) clock-wise to bottom of drain body. Push GASKET (4) down against LOCKNUT (3). Fig. B. 4 2 3 INSTALL DRAIN FROM TIGHTEN LOCKNUT 7 8

Краткое содержание страницы № 4

ATTACH CABLE CONNECTOR 10 Fig. A. Fig. B. Thread CABLE CONNECTOR (1) clockwise onto DRAIN BODY CONNECTION (2) and 1 hand tighten. Fig. A. Your new POP-UP DRAIN installation is now complete. Fig. B. Note: Tailpeice on pop-up drain is 1-1/4” O.D. Fig. B. 2 1-1/4” O.D. CHECK OPERATION OF POP-UP 11 Operate LIFT KNOB (1) to verify that STOPPER (2) opens and closes. Note: If STOPPER (2) does not open and close properly then refer to the “troubleshooting section” of these instructions. 1 2 MAKE WATER S

Краткое содержание страницы № 5

TEST INSTALLED FITTING 13 With HANDLES (1) in OFF position, turn on WATER 6 SUPPLIES (2) and check all connections for leaks. 1 Remove AERATOR (3). First loosen aerator set screw with AERATOR SET HEX WRENCH (6) supplied. Pull out AERATOR (3) with SCREW AERATOR KEY (7). 1 Operate both HANDLES (1) to flush water 3 lines thoroughly. Replace AERATOR (3) and tighten set screw. 7 5 CHECK DRAIN CONNECTIONS 14 Operate POP-UP KNOB (5) and fill Sink with water. Check that DRAIN STOPPER (4) makes a good sea

Краткое содержание страницы № 6

Speed Connect™ Drain Troubleshooting Guide If sink does not hold water even though Stopper is in the “down” position: • Follow CABLE ADJUSTMENT PROCEDURE. If Stopper does not raise up fully or sink drains too slowly: • Follow CABLE ADJUSTMENT PROCEDURE. If you need to remove the Stopper: • Follow STOPPER REMOVAL PROCEDURE. If you would like the ability to remove your Stopper simply by lifting it out of the drain: • Follow STOPPER INSTALLATION PROCEDURE for “Unlocked” mode. C

Краткое содержание страницы № 7

STOPPER INSTALLATION PROCEDURE The Stopper can be installed two ways, “Locked” Mode (Stopper cannot be removed) or “Unlock” Mode (Stopper is removable). Locked Mode: Look at the Plastic Loop at the bottom of the Stopper and notice Fig. G. that the Loop is on one side of the Stopper. Fig. G. LOGO To install the stopper in “Locked” mode, insert the Stopper into the Drain so that the Plastic Loop is facing toward the rear of the Sink and the American Standard logo is facing front. Rotate Stopper s

Краткое содержание страницы № 8

™ ™ BERWICK / BOULEVARD SPREAD LAVATORY FITTING MODEL NUMBER M962817-YYY0A SPOUT KIT 7431.801 7430.801 / 7431.821 7430.821 M962420-YYY0A POP-UP ROD M962837-YYY0A CROSS HANDLE ASSEMBLY M962832-YYY0A RIGHT LEVER HANDLE ASSEMBLY M962831-YYY0A LEFT LEVER HANDLE ASSEMBLY M962905-0070A SPOUT SET SCREW KIT M962818-0070A AERATOR KIT M962830-YYY0A ESCUTCHEON KIT A912831-0070A 918555-0070A SPOUT O-RING HANDLE SCREW 617852-0070A M962492-0070A HANDLE ADAPTER MOUNTING KIT M962544-YYY0A STOPPER ASSEMBLY 9940