Краткое содержание страницы № 1
Curved Planer
82 mm (3-1/4") MODEL 1001
INSTRUCTION MANUAL
Planing depth No load speed
Planing width Overall length Net weight
IRPMI
82 mm 13~114")
3 mm 1118"l 12,000 370 mm 1,14~1/2"1 6.0 kg 113.2 lbsl
Краткое содержание страницы № 2
IMPORTANT SAFETY INSTRUCTIONS WARNING: When using electric tools, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and personal injury, includ- ing the following: READ ALL INSTRUCTIONS. 1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. 2. CONSIDER WORK AREA ENVIRONMENT. Don't use power tools in damp or wet locations. Keep work area well lit. Don't expose power tools to rain. Don't use tool in presence of flammable liquids
Краткое содержание страницы № 3
17. STAY ALERT. Watch what you are doing, use common sense. Don’t operate tool when you are tired. 18. CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard or other part that is damaged should b
Краткое содержание страницы № 4
ADDITIONAL SAFETY RULES 1. Rags, cloth, cord, string and the like should never be left around the work area. 2. Avoid cutting nails. Inspect for and remove all nails from the workpiece be- fore operation. 3. Handle the blades very carefully. 4. Be sure the blade installation bolts are securely tightened before operation. 5. Hold the tool firmly with both hands. 6. Keep hands away from rotating parts. 7. Before using the tool on an actual workpiece, let it run for a while. Watch for vib
Краткое содержание страницы № 5
Removing or installing planer blades WARNING : Always be sure that the tool is switched off and unplugged before removing or installing the blades. To remove the blades on the drum, un- screw the three installation bolts with the socket wrench. The drum cover comes off together with the blades. To install the blades, first clean out all chips or foreign matter adhering to the I Eo1 t drum or blades. Use blades of the same dimensions and weight, or drum oscilla- tionhibration will res
Краткое содержание страницы № 6
Adjusting depth of cut Depth of cut may be adjusted by simply turning the knob on the front of the tool. Adjusting front base 1. To create a curved surface, loosen the wing nut. For a concave planing job, I Convex w raise the front base; for a convex plan- I Cutting line \ ing job, lower the front base. In either case, the front base must be aligned with the cutting line. Then tighten the I WlnO nut wing nut securely. NOTE : As explained later, although the objec- tive is to cut
Краткое содержание страницы № 7
2. To create a flat surface, loosen the wing I nut after setting the tool on a level sur- face. Turn the front knob on the tool Wing nut until the front base is perfectly level with the rear base. Then tighten the wing nut securely. F Switch action To start the tool, simply pull the trigger. Release the trigger to stop. For continuous operation, pull the trigger and then push in the lock button. To stop the tool from the locked position, pull the trigger fully, then release it. WA
Краткое содержание страницы № 8
NOTE : I First take down both *When beginning the planing of a flat ends of the workpiece workpiece to obtain eventually a convex shape, first take down both ends of the workpiece, gradually planing until the ultimate convex shape is achieved. *When beginning the planing of a flat First take down the workpiece to obtain eventually a concave middle of the workpiece shape, first take down the middle of the workpiece, gradually planing until the ultimate concave shape is achieved. Sh
Краткое содержание страницы № 9
Sharpening planer blades I Always keep your blades sharp for the best performance possible. Use the sharpening holder to remove nicks and produce a fine edge. First, loosen the two wing nuts on the holder and insert the blades (A) and (B), so that they contact the sides (C) and (D). Then tighten the wing nuts. Immerse the dressing stone in water for 2 or 3 minutes before sharpening.' Hold the holder so that the blades both contact the dressing stone for simultaneous sharpening at t
Краткое содержание страницы № 10
MAINTENANCE CAUTION : Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. Replacing carbon brushes Remove and check the carbon brushes regularly. Replace when they wear down to the limit mark. Keep the carbon brushes clean and free to slip in the holders. Both carbon brushes should be replaced at the same time. Use only Makita carbon brushes. / Limit mark Use a screwdriver to remove the brush holder caps. Take out the wo
Краткое содержание страницы № 11
ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. 0 Planer blade 0 Planer blade (Material : Tungsten-carbide) Width : 82 mm (3-1/4") Width : 82 mm (3-1 /4") Part No. 793004-6 Part No. 793007-0 0 Blade gauge assembly 0 Sharpening holde
Краткое содержание страницы № 12
Jan 26-89 EN 82 mm (3-1/4") CURVED PLANER Model 1001 Note The switch, noise suppressor and other part configuratlons may differ from country to country 12
Краткое содержание страницы № 13
MODEL 1001 Jan -26-'89 EN ITEM NO z:, DESCRIPTION DESCRIPTION NO USED MACHINE ~ 1 4 Pan Head Screw M5x25 IWith Washer1 33 1 Set Bo11 M8 2 1 Bracket 34 1 Knob 50 1 Ball Bearing 6200LLB 1 3 35 Flaf Washer IO 4 1 Fan 80 36 1 Noise Suppressor 5 1 ARMATURE ASSEMBLY 31 1 Swttch !With lfem 3 71 38 1 Pan Head Screw M4x8 IWith Washer1 6 1 Flaf Washer 12 3Y 1 Handle Cover 1 1 Ball Bearing 6201LLB 40 3 Countersunk Head Screw M4x30 IWith Washer] 8 2 Pan Head Screw M5x60 IWifh Washer) 41 2
Краткое содержание страницы № 14
14
Краткое содержание страницы № 15
Краткое содержание страницы № 16
Makita Corporation 3-11 -8, Sumiyoshi-cho, Anjo, Aichi 446 Japan 883000A0 PRINTED IN JAPAN I991 -1 0 E
