Краткое содержание страницы № 1
ZyXEL
TOTAL INTERNET ACCESS SOLUTION
Prestige 100MH
PSTN Router/Hub
Quick Start Guide
Краткое содержание страницы № 2
Prestige 100MH Quick Start Guide Prestige 100MH PSTN Router/Hub Copyright Copyright © 1998 by ZyXEL Communications Corporation. The contents of this publication may not be reproduced in any part or as a whole, transcribed, stored in a retrieval system, translated into any language, or transmitted in any form or by any means, electronic, mechanical, magnetic, optical, chemical, photocopying, manual, or otherwise, without the prior written permission of ZyXEL Communications Corporation
Краткое содержание страницы № 3
Prestige 100MH Quick Start Guide Table of Contents Chapter 1 Before You Begin 1.1 Purpose Of This Guide.................................................................................... 1 1.2 Who Should Not Use This Guide: .................................................................... 1 1.3 Package Contents .......................................................................................... 1 1.4 Information From Your ISP .....................................................
Краткое содержание страницы № 4
Краткое содержание страницы № 5
Prestige 100MH Quick Start Guide Chapter 1 Before You Begin 1.1 Purpose Of This Guide This guide provides instructions on how to setup your new Prestige and Windows 95/NT workstations for Internet access using the Prestige Web Configurator (PWC). The Prestige Web Configurator provides a quick, simple, and intuitive way to configure your Prestige. Using a “point-and-click” Web-based Graphical User Interface (GUI), you can configure, save, monitor, and diagnose your Prestige from any works
Краткое содержание страницы № 6
Prestige 100MH Quick Start Guide θ One Telephone Cable with RJ-11 Connectors θ One DB-25(male)/DB-9(female) Converter θ One Console RJ-45/DB-25(female) Cable θ One Ethernet 10Base-T cable θ One Prestige Web Configurator CD ROM θ One Prestige Series User's Manual θ One Warranty Registration Card θ One Prestige Web Configurator User’s Guide θ This Prestige Quick Start Guide 1.4 Information From Your ISP Your Internet Service Provider (ISP) should provide information needed to setup your
Краткое содержание страницы № 7
Prestige 100MH Quick Start Guide 1.5 Prestige’s Default TCP/IP Settings 1.5.1 IP Address and Subnet Mask Your Prestige is pre-configured in the factory with IP Address of 192.168.1.1 and subnet mask of 255.255.255.0 (Class C). 1.5.2 DHCP Setting Your Prestige has a built-in DHCP (Dynamic Host Configuration Protocol) server. DHCP allows the individual workstations on a network to obtain their TCP/IP configuration at start-up from a centralized DHCP server (in this case, the Prestige). Th
Краткое содержание страницы № 8
Краткое содержание страницы № 9
Prestige 100MH Quick Start Guide Chapter 2 Cabling & Installation The following diagrams depict the cabling for the Prestige. After you have completed the cabling, proceed to Chapter 3: Windows 95 Quick Start or Chapter 4: Windows NT Quick Start. 2.1 Prestige 100MH Power Power Adapter Outlet PSTN Network (Telephone Line) Computer ETHERNET 4 3 2 1 LINEPHONE CONSOLE POWER Telephone Abcdefg ghijkl Abcdefg mmn ghijkl opqr mmn opqr stuvw xyzasdsad stuvw aa s xyzasdsad aa s dddd . rrrr ddddttt
Краткое содержание страницы № 10
Краткое содержание страницы № 11
Prestige 100MH Quick Start Guide Chapter 3 Windows 95 Quick Start This chapter shows you the step-by-step instructions to configure your Windows 95 workstations for Internet access. 3.1 TCP/IP Installation You must first install TCP/IP protocol on each Windows 95 workstation before you can use it to access the Internet. If you have already installed TCP/IP, skip to the TCP/IP Configuration section on page 9; otherwise, follow these steps: Step 1. From the Start Menu, select Settings the
Краткое содержание страницы № 12
Prestige 100MH Quick Start Guide Step 4. Select the Protocol item and click Add. Step 5. Choose Microsoft from the Manufacturers, and TCP/IP from the Network Protocols. Then click OK. This will install the TCP/IP protocol on your workstation. 8
Краткое содержание страницы № 13
Prestige 100MH Quick Start Guide 3.2 TCP/IP Configuration Follow these steps to setup your TCP/IP configuration for Windows 95. Step 1. From the Start Menu, select Settings then open Control Panel. Step 2. Double-click the Network icon to open the Network control panel. A list of installed components is displayed. Click on TCP/ IP selection for the installed network card to highlight as shown below, then click the Properties button. 9
Краткое содержание страницы № 14
Prestige 100MH Quick Start Guide Step 3. The TCP/IP Properties dialog with IP Address tab will appear as shown below. Step 4. Select Obtain an IP address automatically if your ISP did not assign you a block of registered IP addresses (most cases); otherwise, select Specify an IP address and enter the IP address and subnet mask for this workstation from the block provided by your ISP. Note: Do not assign arbitrary IP address and subnet mask to your workstations. Otherwise, you will not
Краткое содержание страницы № 15
Prestige 100MH Quick Start Guide Step 5. Select the WINS Configuration tab, and click Disable WINS Resolution. Step 6. On the Gateway tab, highlight any installed gateways and click the Remove button until there are none listed. 11
Краткое содержание страницы № 16
Prestige 100MH Quick Start Guide 12
Краткое содержание страницы № 17
Prestige 100MH Quick Start Guide Step 7. On the DNS Configuration tab, select Enable DNS. Enter a unique name for the workstation in the Host box. Enter your domain name in the Domain box if you have one. This field is optional and can be left blank. Leave the DNS Server Search Order box blank if you plan to get the DNS server address(es) from a DHCP server. Otherwise enter the DNS server address of your ISP in the third box and click Add. Click OK to save and close TCP/IP dialog. Step
Краткое содержание страницы № 18
Краткое содержание страницы № 19
Prestige 100MH Quick Start Guide Chapter 4 Windows NT Quick Start This chapter shows you the step-by-step instructions to configure your Windows NT workstations for Internet access. 4.1 TCP/IP Installation You must first install TCP/IP protocol on each Windows NT workstation before you can use it to access the Internet. If you have already installed TCP/IP, skip to the TCP/IP Configuration section on page 15; otherwise, follow these steps: Step 1. From the Start Menu, select Settings th
Краткое содержание страницы № 20
Prestige 100MH Quick Start Guide Step 4. Choose TCP/IP Protocol from the Network Protocol list. Then click OK. This will install the TCP/IP protocol on you workstation. 4.2 TCP/IP Configuration Follow these steps to setup your TCP/IP configuration for Windows NT. Step 1. From the Start Menu, select Settings then open Control Panel. Step 2. Double-click the Network icon to open the Network control panel. 16
