Краткое содержание страницы № 1
Wireless Router RNX-EasyN400
User Manual
Краткое содержание страницы № 2
Wireless RouterRNX-EasyN400 User Manual Safety Warning • Place connecting cables carefully so that no one will step on them or stumble over them. • Always disconnect all cables from this device before servicing or disassembling. • Use ONLY an appropriate power adaptor or cord for your device. • Connect the power adaptor or cord to the right supply voltage (for example, 110V AC i
Краткое содержание страницы № 3
Wireless RouterRNX-EasyN400 User Manual Table of Contents TABLE OF CONTENTS .......................................................................................................................2 BEFORE WE BEGIN ............................................................................................................................4 1 INTRODUCTION ............................
Краткое содержание страницы № 4
Wireless RouterRNX-EasyN400 User Manual 3.7.1 Advanced .................................................................................................................................. 58 3.7.2 Demilitarized Zone (DMZ)....................................................................................................... 58 3.7.3 Denial of Service (DoS)..............................
Краткое содержание страницы № 5
Wireless RouterRNX-EasyN400 User Manual Before We Begin • Please configure RNX-EasyN400 with the computer that was last connected directly to your modem. • You can only use the Ethernet port on your modem. If you were using the USB connection before using RNX-EasyN400, then you must turn off your modem, disconnect the USB cable and connect an Ethernet cable to the Internet por
Краткое содержание страницы № 6
Wireless RouterRNX-EasyN400 User Manual 1 Introduction 1.1 Overview Congratulations on your purchase of RNX-EasyN400 Wireless Network Broadband Router. RNX-EasyN400 is compatible with 802.11g & 802.11b and draft 802.11n v2.0. RNX-EasyN400 is not only a Wireless Access Point, but also doubles as a 4-port full- duplex Switch that connects your wired-Ethernet devices together at in
Краткое содержание страницы № 7
Wireless RouterRNX-EasyN400 User Manual enhance security Make wireless AP and Bridge mode WDS (Wireless Distribution System) simultaneously as a wireless repeater ** Theoretical wireless signal rate based on IEEE standard of 802.11a, b, g, n chipset used. Actual throughput may vary. Network conditions and environmental factors lower actual throughput rate. All specifications a
Краткое содержание страницы № 8
Wireless RouterRNX-EasyN400 User Manual 1.4 Product Layout and LED Signal LED Color Status Description RNX-EasyN400 is receiving power and functioning On POWER properly. Amber Blinking RNX-EasyN400 is performing test or reset Off RNX-EasyN400 is not receiving power RNX-EasyN400 is ready, but not sending/receiving On wireless signals RNX-EasyN400 is sending/recei
Краткое содержание страницы № 9
Wireless RouterRNX-EasyN400 User Manual Blinking RNX-EasyN400 is sending/receiving data through WAN Off The WAN is not ready or fail On RNX-EasyN400 has a successful Ethernet connection. RNX-EasyN400 is sending/receiving data through LAN LAN 1~4 port Blue Blinking port Off The LAN is not ready or fail Press this button for 1 second to set up a wireless connection via WiFi Prot
Краткое содержание страницы № 10
Wireless RouterRNX-EasyN400 User Manual 1.7 RNX-EasyN400’s LAN & WAN Cable Connection Setup WAN connection: Connect Ethernet cable between WAN ports of your ADSL/CABLE modem & INTERNET port of RNX-EasyN400. Make sure your ADSL/CABLE modem is working well. Contact your ISP if you have any questions. RNX-EasyN400 Rear View + Intnernet plugin RNX-EasyN400 WAN Connection
Краткое содержание страницы № 11
Wireless RouterRNX-EasyN400 User Manual RNX-EasyN400 LAN Connection Diagram 10
Краткое содержание страницы № 12
Wireless RouterRNX-EasyN400 User Manual 2 Setup Wizard We will introduce the Smart Wizard in this section. Please make sure the following before insert the CD into the CD/DVD drive: • Internet connection should be setup & ready to use (ADSL or cable modem). • Modem must provide a RJ45 port to connect with RNX-EasyN400. Please refers to previous page’s “RNX-EasyN400 LAN Connect
Краткое содержание страницы № 13
Wireless RouterRNX-EasyN400 User Manual Click User Manual to open user manual. Click Adobe Reader to install Adobe Acrobat reader on your PC/Notebook. Click EXIT anytime you want to abort. 2.2 Setup Wizard – Configuration Click to proceed. Click to abort. RNX-EasyN400 should be setup as depicted above. 12
Краткое содержание страницы № 14
Wireless RouterRNX-EasyN400 User Manual Make sure your DSL/CABLE modem is setup and working. Else take the help of your internet service provider. Click to proceed. Check the MODEM and RNX-EasyN400 connection. It should be as shown below. Check power connection for modem as well as RNX-EasyN400. Click to proceed. 13
Краткое содержание страницы № 15
Wireless RouterRNX-EasyN400 User Manual Notice the LED will light up at this stage. If not, check your procedures again. Click to configure WAN & Wireless settings. The Wizard page will show up as below: 14
Краткое содержание страницы № 16
Wireless RouterRNX-EasyN400 User Manual Then, you will be prompt to RNX-EasyN400 login page User name and password are admin/admin. Click . Your default browser will connect to RNX-EasyN400 Web Server http://192.168.0.1 . 15
Краткое содержание страницы № 17
Wireless RouterRNX-EasyN400 User Manual Click to enter mode selection. 2.3 Setup Wizard – Connect Mode Selection This is where you select the mode that RNX-EasyN400 is going to be use and set its configurations. You can choose AP Router Mode is when you want to set RNX- EasyN400 as a wireless LAN administrator for your computer or gaming console to connect to. Or you can
Краткое содержание страницы № 18
Wireless RouterRNX-EasyN400 User Manual Depending on your Network setting, Wizard will show you either one of the pages below, the best detecting option will be selected, please click unless you want to manually configure your connecting option. 2.3.1.1 DHCP Mode Selection Smart Wizard has detected DHCP client. Click , you will see the page show below which ask
Краткое содержание страницы № 19
Wireless RouterRNX-EasyN400 User Manual LABEL DESCRIPTION Host Name This is optional. Depending on if your ISP require you to provide this information. Please leave this blank, if you are not sure. MAC address The default value when Click is set to the WAN’s physical interface of the broadband router. Smart Wizard has finished setting up WAN Configuration.
Краткое содержание страницы № 20
Wireless RouterRNX-EasyN400 User Manual Please choose your security level, and enter your desired name for your wireless network (SSID) and security key (Key); Click to proceed. Depending on how you set up RNX-EasyN400, you will see different result pages before you reboot your RNX-EasyN400. 19
